Audi A4 allroad Service Bulletins
2,517 manufacturer communications on file.
- April 7, 2015•Document ID: 10119999Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- A741521 2036572-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 74 number 14-19 dated May 9, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damaged is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. This occurs when the rear seat is folded down with the headrests installed, and the front seat is moved back far enough to make contact with the rear seat headrest.
Associated Products (32)2017 Audi A32017 Audi A4 allroad2017 Audi A52017 Audi allroad2016 Audi A32016 Audi A4 allroad2016 Audi A52016 Audi allroad2015 Audi A32015 Audi A4 allroad2015 Audi A52015 Audi allroad2014 Audi A32014 Audi A4 allroad2014 Audi A52014 Audi allroad2013 Audi A32013 Audi A4 allroad2013 Audi A52013 Audi allroad+ 12 moreAssociated Documents - March 27, 2015•Document ID: 10119962Service Bulletin/Repair InstructionsLANE DEPARTURE; LANE DEPARTURE: ASSIST
- Mfr Comm. #:
- A961594 2035047-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 96 number 13-79 dated December 5, 2013. Audi side assist deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information panel. The system can be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Workshop finds that sporadic DTCs are stored in the lane change assistance control module, Audi side assist can be activated without issue, no obstructions found on the outside or inside of the bumper, no rework of the bumper can be found, the control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found on the inside or on the outside rear bumper area, and the control module mounting brackets are not broken or loose.
Associated Products (6)Associated Documents - March 25, 2015•Document ID: 10119961Service Bulletin/Repair InstructionsLANE DEPARTURE: BLIND SPOT DETECTION; ELECTRICAL SYSTEM:SOFTWARE; LANE DEPARTURE: ASSIST
- Mfr Comm. #:
- A961593 2031095-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 96 number 13-51 dated February 15, 2013. Audi side assist deactivates immediately after the engine is started. DTC C1115F2 (Lane change assistance control module 2 Function limitation due to insufficient voltage) is logged in the lane change assistance control module. The software of the lane change assistance control module, J769 (3C), has been optimized to remove this condition.
Associated Products (3)Associated Documents - March 24, 2015•Document ID: 10120679Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- A661549 2030471-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate-length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
Associated Products (66)Associated Documents - March 23, 2015•Document ID: 10119947Service Bulletin/Repair InstructionsSTEERING:COLUMN; STEERING
- Mfr Comm. #:
- A481565 2034351-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 48 number 14-57 dated January 29, 2014. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
Associated Products (25)Associated Documents - March 20, 2015•Document ID: 10119957Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- A911580 2036575-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. This profile will be used each time the voice recognition system is used without a phone being paired to the MMI. This TSB is informational only and not applicable to any Audi warranty.
Associated Products (37)Associated Documents - March 20, 2015•Document ID: 10119956Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- A911579 2038824-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
Associated Products (207)Associated Documents - March 17, 2015•Document ID: 10119945Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- A101511 2018288-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
Associated Products (191)Associated Documents - March 12, 2015•Document ID: 10120675Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:COOLING SYSTEM
- Mfr Comm. #:
- A191557 2040043-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummaryCustomer states that engine overheats. No MIL. No related DTCs are stored. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the overheat condition for the vehicles listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above. No changes to production have been made, as no issue has been identified.
Associated Products (14)Associated Documents - March 11, 2015•Document ID: 10067937Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- 03-11-2015-US
- Date Added:
- May 23, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - March 10, 2015•Document ID: 10119955Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- A911578 2011500-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
Associated Products (177)Associated Documents - March 9, 2015•Document ID: 10119940Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- A011514 2014753-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
Associated Products (182)Associated Documents - March 6, 2015•Document ID: 10119946Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- A171557 2010043-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
Associated Products (198)Associated Documents - March 4, 2015•Document ID: 10119958Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- A941564 2017806-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 15-60 dated February 12, 2015. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
Associated Products (42)Associated Documents - March 3, 2015•Document ID: 10120672Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- A151526 2039995-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummaryRattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner.
Associated Products (48)Associated Documents - March 3, 2015•Document ID: 10119953Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- A911576 2039476-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummaryThe customer complains that the Audi Connect Online service only reaches 2G service within the Indianapolis metropolitan area. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and Q7 vehicles. For 2012-2013 A6 and A7 vehicles, see TSB 2039515. A telephone module that supports 3G service on the 1900MHZ band was installed beginning with model year 2014 vehicles.
Associated Products (7)Associated Documents - February 23, 2015•Document ID: 10120689Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:COOLING SYSTEM
- Mfr Comm. #:
- A191555 2039891-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummaryHeating performance is low. Air bubble noises are heard from coolant and/or heat exchanger area. The check valve in the breather line can come loose. As a result, air may get into the coolant system. Modified parts in production starting with production date 2/5/2015.
Associated Products (11)Associated Documents - February 19, 2015•Document ID: 10120707Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- A941562 2032852-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 13-09 dated February 26, 2013. Only vehicles with xenon headlights (PR No 8Q3 or 8Q5) are affected. Customer complains that the headlights appear to be adjusted too low and the overall illumination pattern on the road is too short, particularly when driving on non-highway roads. Workshop finds that the illumination pattern on the road is the same when compared to similarly-equipped xenon headlight vehicles.
Associated Products (4)Associated Documents - February 19, 2015•Document ID: 10120699Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS; SERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES
- Mfr Comm. #:
- A461505 2038056-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit.
Associated Products (37)Associated Documents - February 17, 2015•Document ID: 10120684Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- A011509 2037307-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 01 number 14-78 dated May 28, 2014. MIL is on due to DTC P013E00 being stored in the ECM. ECM software needs to be updated.
Associated Products (4)Associated Documents