Mercedes-Benz Metris Service Bulletins (2021)
40 manufacturer communications on file.
- July 1, 2026•Document ID: 11035563Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- LI54_30-N-080701
- Date Added:
- August 3, 2026
- Manufacturer:
- MERCEDES-BENZ
SummaryASSYST PLUS service reminder appears earlier than expected due to vehicle operating conditions Complaint The ASSYST PLUS service reminder appears earlier than expected. The customer or dealer may report that the vehicle did not reach the starting maintenance interval shown in vehicle documentation, option coding, sales literature, or the Owner's Manual. The service reminder may appear significantly earlier than anticipated even though no faults are stored and no malfunction is present in the vehicle. The remaining distance and remaining time continue to decrease normally until the service reminder is displayed. Cause This condition is not caused by a malfunction of ASSYST PLUS. ASSYST PLUS is a dynamic maintenance management system that continuously evaluates vehicle usage and opera-ting conditions to determine maintenance requirements. The starting maintenance interval specified by variant coding represents a maximum interval that may only be achieved under favorable operating conditions. Actual maintenance intervals may be significantly shorter depending on vehicle use. Vehicle operating conditions such as driving conditions, engine load, engine operating conditions, idling, short-trip operation, environmental influences, oil aging, and Diesel Particulate Filter (DPF) regeneration activity may reduce the maintenance interval from its starting value. These conditions may accelerate engine oil aging through increased soot loading, fuel dilution, moisture accumulation, and additional engine operating stress. As a result, the remaining distance and remaining time until the next service may be reduced from the starting maintenance interval. Remedy Do not replace any parts. A due service must be assumed if the maintenance data calculated by ASSYST PLUS indicates that service is required.
Associated Products (3)Associated Documents - June 8, 2026•Document ID: 11034417Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- LI80.20-N-079697
- Date Added:
- July 2, 2026
- Manufacturer:
- MERCEDES-BENZ
SummaryAcoustic Warning or message occurring when a closed sliding door is not recognized Complaint Customer may state the warning message or indicator accompanied by acoustic tone alerting the sliding door is ajar when the door is completely closed Cause There are several reasons that lead to the failure occurring: - Mechanical damage through bending when loading and unloading - Worn contact plates --> After detachment of silver plating, the coper plate is corroded - Movement of sliding door/body when driving --> Contact pins do not always make contact with contact plate --> Central locking system fault message in instrument cluster Remedy In a problem case, replace contact switch for vehicles with +T50/+T55/+EL9 or contact plate with A4478201903. Remember to check the fit of the sliding doors and make any necessary adjustments as per AR72.16-S-1023E (447/448) and AR72.16-D-1023TS (907/910). Further valid damage codes: 82326 Contact switch for central locking system on sliding door 82347 Contact plate for central locking system on sliding door 53196 K/Z contact plate for central locking system on sliding door 82645 Contact switch for sliding door
Associated Products (3)Associated Documents - June 3, 2026•Document ID: 11034416Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- LI49.10-N-080528
- Date Added:
- July 2, 2026
- Manufacturer:
- MERCEDES-BENZ
SummaryOM642 DPF Filter Cracked or Broken Complaint Vehicle will not start or exhibits noisy exhaust. Check Engine Lamp (CEL) is on. Multiple control unit communication and system faults may be present, including but not limited to: 134800, 134900, 11B300, 11EC00, 15E100, 155700, 162500. Additional events codes may include: 134300, 102200, 163400, 16CE00. In many cases, multiple unrelated faults are stored due to electrical disruption from wiring damage rather than indivi-dual component failure. Cause The DPF filter is cracked, broken, or leaking, allowing hot exhaust gas to escape from the exhaust system. Depending on the location of the break or leak, hot exhaust gas may be directed toward the main wiring harness and/ or the SCR (Selective Catalytic Reduction) dosing valve assembly. This heat exposure can result in: • Internal melting of wiring insulation within the harness • Short to ground conditions and loss of communication between control units • Damage to the dosing valve and/or heated AdBlue line Damage to the wiring harness may not be visible externally, as the outer tape can remain intact while the internal wires are melted and fused together. Remedy Inspect the DPF assembly for cracks, separation, or leakage. Do not proceed with further diagnosis or component replacement until the exhaust leak source has been identified and confirmed. If any damage is found, replace the DPF filter assembly. Based on the location of the failure, inspect all components in the path of the exhaust leak, including the dosing valve assembly and main wiring harness. The wiring harness must be opened in any area exposed to the exhaust leak to visually inspect the individual wires. External inspection alone is not sufficient to determine harness condition. Repair or replace any damaged wiring in accordance with approved repair procedures. Replace any dosing system components that show signs of heat damage. Failure to identify and repair all heat-affected components will result in repeat faults or no-start conditions.
Associated Products (3)Associated Documents - May 7, 2026•Document ID: 11033163Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; FUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- LI47.50-N-072080_4
- Date Added:
- June 2, 2026
- Manufacturer:
- MERCEDES-BENZ
SummaryCheck engine light on and FC P146264 stored in engine and fuel pump control units Complaint Check engine light active and FC P146264 Temp. and pressure sensor B4/15 is stored in Engine control unit and Fuel pump control unit. Cause Software parameter in Fuel pump control unit. Remedy Update fuel pump control unit (FSCU) to software version A0009024488 A0009030664. Clear fault codes and check for any additional symptoms.
Associated Products (3)Associated Documents - October 6, 2025•Document ID: 11024928Over The AirUNKNOWN OR OTHER
- Mfr Comm. #:
- 24V5497749
- Date Added:
- November 4, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryThe software for the communication module does not correspond to the latest series production configuration. For this reason, a remote software update to update the software for the communication module is planned for the affected vehicles. This update includes quality-enhancing optimizations for the communication module to improve the system stability and accessibility of connected services. MBUSA is conducting a service campaign. The update is downloaded and installed in the background. This process takes approximately 10 minutes. During installation, the system can be used without restrictions. The new software will become active after the vehicle's ignition cycle.
Associated Products (3)Associated Documents - September 16, 2025•Document ID: 11023982Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI27.19-N-079793
- Date Added:
- October 7, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns. If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.
Associated Products (3)Associated Documents - April 3, 2025•Document ID: 11017558Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI01.20-N-079115_1
- Date Added:
- May 2, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryCheck engine light illuminated - Fault code current P04D-B79 The crankcase ventilation system is interrupted. Complaint: Check engine light on. Fault code P04DB79 is current in the engine control module (N3/10). Cause: Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for S208 vent line contact switch. Refer to attached photo of connection location. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found.
Associated Products (3)Associated Documents - March 10, 2025•Document ID: 11016430Service Bulletin/Repair InstructionsVISIBILITY/WIPER
- Mfr Comm. #:
- LI82.35-N-078930
- Date Added:
- April 3, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryWarning Lamp "Washer Fluid Empty" Yet Reservoir Is Not Empty Complaint: Warning lamp "washer fluid empty", even thought the washer fluid reservoir is full Cause: Insufficient electrical conductivity of the washer fluid, as the washer fluid was mixed with distilled water. Tip: The washer fluid sensor detects the electrical conductivity. If air is present without electrical conductivity between the measuring points, as is the case with an empty tank, an empty tank is detected by the sensor. Distilled water also does not have electrical conductivity, meaning that the sensor detects an empty tank, even if this is not the case. Remedy: Fill reservoir with standard washer fluid and water (no distilled water) in an adequate ratio in order to ensure electrical conductivity. Exchange of the reservoir with a welded-in sensor is only required if filling with conductive washer fluid has not provi- ded a remedy. This can be made certain by utilizing water with a light amount of salt dissolved in to it for stronger con- ductivity.
Associated Products (3)Associated Documents - February 28, 2025•Document ID: 11014718Service CampaignSTRUCTURE:BODY
- Mfr Comm. #:
- VS2SPANBA
- Date Added:
- March 4, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz Metris Vans, has determined that the weld nuts on the longitudinal member were not installed according to current production specifications. An authorized Mercedes-Benz dealer will replace and install new weld nuts on the longitudinal member.
Associated Products (1)Associated Documents - February 12, 2025•Document ID: 11014726Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- LI07.70-N-078824
- Date Added:
- March 4, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Cause Various causes Remedy Up to Model year 2018: Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the gui- ded test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. Model year 2019 and later: Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
Associated Products (3)Associated Documents - February 6, 2025•Document ID: 11013887Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI13.22-N-078825_1
- Date Added:
- February 6, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryM274 poly-V belt squeaking noises, falls off, not aligned, broken
Associated Products (3)Associated Documents - November 28, 2024•Document ID: 11011223Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI49.00-N-078608
- Date Added:
- December 4, 2024
- Manufacturer:
- MERCEDES-BENZ
SummarySMOG/Emissions Test fail due to one or more Readiness Monitors not set Complaint: The vehicle has failed the State Emissions Certification because one or more of the OBDII readiness monitors are not completely set. Cause: One or more of the following Readiness Monitors are not fully set within XENTRY: Misfire Monitoring - Injection System Fuel System Monitoring - Injection System, Fuel System, EGR Valve, O2 Sensor NMHC Catalyst Monitoring - NMHC/Diesel Oxidation Catalyst NOx Aftertreatment Monitoring - SCR Catalyst System Boost Pressure System Monitoring - Turbocharger, Charge Air System Exhaust Gas Sensor Monitoring - O2 Sensor, NOx Sensors Diesel Particulate Filter Monitoring - Diesel Particulate Filter System Exhaust Gas Recirculation System Monitoring - EGR Valve and system Remedy: Please complete the required driving conditions to fully set the incomplete Readiness Monitor. DO NOT: - Erase any fault codes. If fault codes are present, process these and allow the readiness drives to clear fault codes. - Flash or SCN code the CDI or SCR control units. - Perform a manual DPF regeneration, unless instructed below. - Disconnect the main battery.
Associated Products (3)Associated Documents - October 25, 2024•Document ID: 11009854Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI08.10-N-078545
- Date Added:
- November 5, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint: Noises when reversing slowly <5 km/h (squeaking) Cause: There is a seal in the electric drivetrain that seals off the coolant system from the electric motor. This seal is moistened with coolant during forward travel. As a result of the change in rotational direction when reversing slowly, it may be the case that this sealing ring is no longer moistened. Squeaking noises may occur as a result of the so-called "stick-slip effect". This behavior does not impact the function or durability of the sealing ring and electric drivetrain. Remedy: Do not replace any parts. Explain the cause of the noises to the customer.
Associated Products (4)Associated Documents - July 12, 2024•Document ID: 11005572Service CampaignUNKNOWN OR OTHER
- Mfr Comm. #:
- VS2RADREI
- Date Added:
- August 3, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz Vans, has determined that on certain Sprinter and Metris vehicles, the B-pillar certification label might not contain information on the vehicle's rim size, tire size, and cold tire inflation pressure required under FMVSS 110 or, as applicable, FMVSS 120. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this non-compliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes- Benz dealer will replace the Certification Label on the affected vehicles.
Associated Products (3)Associated Documents - December 19, 2023•Document ID: 10249334Service Bulletin/Repair InstructionsEQUIPMENT; VISIBILITY; STRUCTURE
- Mfr Comm. #:
- PDAGLACKHA
- Date Added:
- January 29, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG has determined that on certain Metris (447 platform) vehicles, the fuel pump impeller might not meet specifications in regards to material characteristics. As a consequence, the impeller might deform. It might therefore come into contact with the fuel pump housing, leading to a mechanical resistance. In some instances, this could lead to a shutdown of the fuel pump. As a result, the vehicle could lose propulsion, and increase the risk of a crash or injury.
Associated Products (3)Associated Documents - December 13, 2023•Document ID: 10249331Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 2023100006
- Date Added:
- January 29, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Metris vans, has determined that on certain Metris (447 platform) vehicles the fuel pump impeller might not meet specifications in regards to material characteristics. As a consequence, the impeller might deform and come into contact with the fuel pump housing, leading to a mechanical resistance. In some instances, this could lead to a shutdown of the fuel pump. As a result, the vehicle could lose propulsion, which could increase the risk of a crash or injury.
Associated Products (2)Associated Documents - July 13, 2023•Document ID: 10240168Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- LI46.35-N-076604
- Date Added:
- August 2, 2023
- Manufacturer:
- MERCEDES-BENZ
SummaryVarious concerns in relation to electric power steering including Rattling/humming noise from electric power steering when steering fully turned (see video recordings 01 and 02).
Associated Products (2)Associated Documents - July 6, 2023•Document ID: 10240175Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:INFOTAINMENT
- Mfr Comm. #:
- LI82.85-N-074054
- Date Added:
- August 2, 2023
- Manufacturer:
- MERCEDES-BENZ
SummaryThe connection of the customer's smartphone connected via the original USB cable is disconnected after an undefined period of time for no apparent reason. The Apple iPhone 12 and subsequent models are primarily affected by this. Hardware for radio control unit (Audio) (N87/15) Modification to hardware for radio control unit (Audio) (N87/15). Note: In isolated cases, the replacement chain is not depicted correctly in XENTRY Parts Information (XPI). Please ensure that one of the following replacement part numbers (suitable for the vehicle equipment) is ordered: ⢠Audio30 - A4479002421 ⢠Audio40 - A4479002721 Note: Please refer to this LI in the "Notes" section of the warranty claim
Associated Products (2)Associated Documents - July 5, 2023•Document ID: 10241385Service Bulletin/Repair InstructionsFUEL SYSTEM, OTHER:DELIVERY
- Mfr Comm. #:
- MB Initial NCU
- Date Added:
- August 28, 2023
- Manufacturer:
- MERCEDES-BENZ
SummaryReplace Fuel Delivery Module.
Associated Products (2)Associated Documents - November 9, 2022•Document ID: 10228605Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NCU-VS2SIMKOM
- Date Added:
- January 3, 2023
- Manufacturer:
- MERCEDES-BENZ
Summary(RC)Update Hermes Communication Module Software
Associated Products (1)Associated Documents