Mercedes-Benz G-Class Service Bulletins (2024)

129 manufacturer communications on file.

• January 2, 2026•Document ID: 11026968

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.70-P-079903

  Date Added:

  January 5, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noise interference when using the hands-free system (phone call). Cause The noise is caused by electromagnetic interference (EMC fault) affecting the microphone lines and thus impacting voice quality. The severity of these faults may vary depending on the vehicle. Remedy To avoid EMC-related interference noise, the SOS microphone line is no longer routed through the rear-installed head unit (A26/17) but is instead routed directly from the new double microphone to the telematics control unit (N112/9). The work instruction for implementation is attached to this document and must be completed in full. Operation steps from the attachment: • Slide 6: Unpin connector A at the head unit (A26/17) pin 19 and pin 6, insulate them, and tie them back. These lines are no longer needed. • Slide 8: Replace front left microphone with double microphone (A213 820 2801) (AR82.70-P-8969XG). Info: The installation location of the double microphone is always front left. There is no difference here between the righthand drive or left-hand drive versions. • Slide 10: Pin the double microphone wiring harness to connector X58/3X1 at pin 1 (white) and pin 14 (screen). • Slide 12: Unpin the Hermes wiring harness at connector X58/3X1 pin 1 (black line) and pin the white line in its place. Connect to pin 14 (brown line). Insulate the black line and tie it back. • Slide 18: Unpin pin 29 (brown), pin 30 (white), and pin 31 (black) from connector 1 on the HERMES (N112/9). Pin the screen (black line) to pin 31. Pin brown to pin 29 and signal (white) to pin 30. Note on parts availability: In December 2025 and January 2026, there may be limited availability of repair wiring harnesses.

  Associated Products (6)

  2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11026968-0001.pdf↗
• December 20, 2025•Document ID: 11026833

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.35-P-080160

  Date Added:

  December 24, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint (Original LI document #: LI27.35-P-079039) Clicking noises from the electro-hydraulic control unit (EHS) when the vehicle is stationary and ECO Start/Stop is active (combustion engine is off). The noise is more noticeable outside the vehicle and in acoustically shielded areas such as closed rooms or garages. Cause The noise in the valve body (EHS) is caused by superimposed pressure peaks acting on the valves. This phenomenon occurs only after a certain running-in period due to the influence of micro-contamination in the valve bores. Remedy A hardware modification of the electro-hydraulic control unit (EHS) is currently being implemented (no change to the part number). This will be incorporated into series production and as a spare part starting from 12/2025. This is only a comfort-related complaint and has no impact on the functionality or service life of the transmission. For sensitive customers, the following measures can be performed: 1. Replace the electro-hydraulic control unit (EHS), the oil pan, and the transmission fluid. - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See attached location guide)

  Associated Products (104)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class+ 84 more
  Associated Documents

  • DownloadMC-11026833-0001.pdf↗
• December 11, 2025•Document ID: 11026593

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI54.71-P-078112

  Date Added:

  December 11, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The concern is characterized by BOTH of the following. 1. "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND 2. Stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cause Missing wire between Drive Unit (N145) and Supercap (C8). Remedy Please reference the following attachments prior to starting work to familiarize and verify the locations of the components: • Drive Unit (N145) - See attachment "Location of Drive Unit in the vehicle". • Supercap (C8) - See attachment "Location of Supercap C8 in the vehicle". Professionally create a new connection by: • Using a red/white cable with cross-section 0.35 mm² and overall length of approximately 2m. • Connect Drive Unit (N145) plug A pin 18 to the 3-pin plug of the Supercap (C8) terminal 15 pin 2. Reference the new wire routing location as shown by the red line in "Picture 1 - Connection from Supercap to Drive Unit". • The new wire should be added to the existing wiring harness as shown by the red line "Picture 1 - Connection from Supercap to Drive Unit". • Z-Splice is the preferred method using A 000 982 91 10 for the Supercap (C8) connection. NOTE: All WIS instructions must be followed for wiring modifications. Damage code: 0 - 51422 - ** - 7 (for ** please state the following: "missing connection ex factory"). If the vehicle has had the modification completed and returns with an exact matching "complaint", please open a TIPS case.

  Associated Products (14)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11026593-0001.pdf↗
• December 11, 2025•Document ID: 11026611

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  December 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (116)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class+ 96 more
  Associated Documents

  • DownloadMC-11026611-0001.pdf↗
• November 10, 2025•Document ID: 11025471

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.35-P-079971

  Date Added:

  November 11, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Possible complaints about shift quality, issues with learning the park lock, and slipping/rinse entries in the EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under “Cause”), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)

  Associated Products (94)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class+ 74 more
  Associated Documents

  • DownloadMC-11025471-0001.pdf↗
• November 6, 2025•Document ID: 11025544

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI68.20-P-080012

  Date Added:

  November 14, 2025

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

  Associated Products (67)

  2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class+ 47 more
  Associated Documents

  • DownloadMC-11025544-0001.pdf↗
• November 3, 2025•Document ID: 11025100

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.10-P-075869

  Date Added:

  November 6, 2025

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right 7. Perform an extended 200mi road test to ensure the clutches are properly conditioned with the new oil. 8. Reassess the concern and release the vehicle if no longer present. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

  Associated Products (103)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class+ 83 more
  Associated Documents

  • DownloadMC-11025100-0001.pdf↗
• October 20, 2025•Document ID: 11024405

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-079904

  Date Added:

  October 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

  Associated Products (98)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class+ 78 more
  Associated Documents

  • DownloadMC-11024405-0001.pdf↗
• September 25, 2025•Document ID: 11023347

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-071499

  Date Added:

  September 25, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

  Associated Products (114)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE+ 94 more
  Associated Documents

  • DownloadMC-11023347-0001.pdf↗
• September 17, 2025•Document ID: 11023193

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-072588

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

  Associated Products (143)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class+ 123 more
  Associated Documents

  • DownloadMC-11023193-0001.pdf↗
• August 15, 2025•Document ID: 11022058

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI09.10-P-079599

  Date Added:

  August 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light illuminated. Fording not available message in instrument cluster. Fault code stored - P153073 Left air flap 'Air intake" has a malfunction. Cause Flap sticking inside air duct of cold air intake Remedy Replace air duct segment of cold air intake. Clear fault codes and check for any further symptoms.

  Associated Products (2)

  2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11022058-0001.pdf↗
• August 14, 2025•Document ID: 11021966

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.15-P-076223

  Date Added:

  August 18, 2025

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint: Creaking or humming noise during adjustment of the electric steering column, see video. Cause: The noises occur due to insufficient greasing of the steering column adjustment guide. Remedy: Disassemble bellows of steering column tube module. Move steering column entirely out and entirely down. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). Move column up 1/4 of the way and grease again. Continue until upper limit stop is reached. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. If noise does not resolve, perform above procedure again. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. If noise still does not resolve, please open a TIPS case.

  Associated Products (14)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11021966-0001.pdf↗
• August 5, 2025•Document ID: 11021898

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI72.10-P-079446

  Date Added:

  August 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint: Customer complaint concerns wind/clattering noises upwards of 20mph in the area of the A-pillar, the outside mirror or at the front doors (cf. attachment). Cause: Cover trim on the underside of the outside mirror. Remedy: For troubleshooting, mask off the cover trim on the underside of the outside mirror (see attachment) and perform a test drive. If the problem can no longer be perceived, seal the cover trim with a butyl/sealing cord or replace if necessary.

  Associated Products (6)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11021898-0001.pdf↗
• July 25, 2025•Document ID: 11021141

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  August 1, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: • Driving style • Brake pressure and application style (stop-and-go traffic with consistent low brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). • Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and brake paste as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". If adhesive is already installed on backing plate, you may gently scrape off and re-apply a new adhesive. In some instances the adhesive may be very carefully removed and Molykote applied instead. 4. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 5. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

  Associated Products (122)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 102 more
  Associated Documents

  • DownloadMC-11021141-0001.pdf↗
• July 16, 2025•Document ID: 11020807

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI01.40-P-079518

  Date Added:

  July 22, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customer complains of oil use, oil leaking or oil smell. Upon inspection oil will be seen at or around the rear of the engine and at the engine/transmission interface. Cause Oil leaking from rear main seal and/or rear main seal plate. Remedy If the rear main seal plate has been previously replaced per the instructions in this LI, open a TIPS case before proceeding. Inspect the rear main seal very carefully. Make sure the seal is not sucked in, rolled, or cut (see pictures in attachments). Confirm the leak location is at the rear main seal and/or rear main seal plate by cleaning the area thoroughly and applying trace powder to the suspected area. Allow the vehicle to run either on a lift or at low speed in a controlled environment (do not attempt at high speed or in wet areas as this will make the results difficult to assess). If the leak is emanating from the seal: replace both air/oil separators. Then clean the bellhousing area completely and test with trace powder again to see if the leak remains. If it doesn't, release the car. If the leak remains pull the rear main seal plate, clean the block mating surface completely and replace the rear main seal plate and rear main seal. When the new seal is installed make sure the sealant path is followed exactly as it is shown per the drawing in the attachments. Apply the sealant to the BLOCK instead of the plate to ensure adequate coverage is attained. After installation lubricate a feeler gauge with oil and run it between the rear main seal and the crank to clear any small debris that may be present and to break any binding or stiction.

  Associated Products (58)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class+ 38 more
  Associated Documents

  • DownloadMC-11020807-0001.pdf↗
• July 11, 2025•Document ID: 11020698

  Service Bulletin/Repair Instructions
  FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-078112

  Date Added:

  July 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The concern is characterized by BOTH of the following. 1. "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND 2. Stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cause Missing wire between Drive Unit (N145) and Supercap (C8). Remedy Please reference the following attachments prior to starting work to familiarize and verify the locations of the components: • Drive Unit (N145) - See attachment "Location of Drive Unit in the vehicle". • Supercap (C8) - See attachment "Location of Supercap C8 in the vehicle". Professionally create a new connection by: • Using a red/white cable with cross-section 0.35 mm² and overall length of approximately 2m. • Connect Drive Unit (N145) plug A pin 18 to the 3-pin plug of the Supercap (C8) terminal 15 pin 2. Reference the new wire routing location as shown by the red line in "Picture 1 - Connection from Supercap to Drive Unit". • The new wire should be added to the existing wiring harness as shown by the red line "Picture 1 - Connection from Supercap to Drive Unit". • Z-Splice is the preferred method using A 000 982 91 10. • Crimp Contact Pin (MLK) for the Drive Unit (N145) is A0485450328. NOTE: All WIS instructions must be followed for wiring modifications. Damage code: 0 - 51422 - ** - 7 (for ** please state the following: "missing connection ex factory"). If the vehicle has had the modification completed and returns with an exact matching "complaint", please open a TIPS case.

  Associated Products (6)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11020698-0001.pdf↗
• July 8, 2025•Document ID: 11020643

  Service Bulletin/Repair Instructions
  FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-078112

  Date Added:

  July 10, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The concern is characterized by BOTH of the following. 1. "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND 2. Stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cause Missing wire between Drive Unit (N145) and Supercap (C8). Remedy Please reference the following attachments prior to starting work to familiarize and verify the locations of the components: • Drive Unit (N145) - See attachment "Location of Drive Unit in the vehicle". • Supercap (C8) - See attachment "Location of Supercap C8 in the vehicle". Professionally create a new connection by: • Using a red/white cable with cross-section 0.35 mm² and overall length of approximately 2m. • Connect Drive Unit (N145) plug A pin 18 to the 3-pin plug of the Supercap (C8) terminal 15 pin 2. Reference the new wire routing location as shown by the red line in "Picture 1 - Connection from Supercap to Drive Unit". • The new wire should be added to the existing wiring harness as shown by the red line "Picture 1 - Connection from Supercap to Drive Unit". • Z-Splice is the preferred method using A 000 982 91 10. • Crimp Contact Pin (MLK) for the Drive Unit (N145) is A0485450328. NOTE: All WIS instructions must be followed for wiring modifications. Damage code: 0 - 51422 - ** - 7 (for ** please state the following: "missing connection ex factory"). If the vehicle has had the modification completed and returns with an exact matching "complaint", please open a TIPS case.

  Associated Products (6)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11020643-0001.pdf↗
• June 17, 2025•Document ID: 11019639

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-078112

  Date Added:

  June 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The concern is characterized by BOTH of the following. 1. "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND 2. Stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cause Missing wire between Drive Unit (N145) and Supercap (C8). Remedy Please reference the following attachments prior to starting work to familiarize and verify the locations of the components: • Drive Unit (N145) - See attachment "Location of Drive Unit in the vehicle". • Supercap (C8) - See attachment "Location of Supercap C8 in the vehicle". Professionally create a new connection by: • Using a red/white cable with cross-section 0.35 mm² and overall length of approximately 2m. • Connect Drive Unit (N145) plug A pin 18 to the 3-pin plug of the Supercap (C8) terminal 15 pin 2. Reference the new wire routing location as shown by the red line in "Picture 1 - Connection from Supercap to Drive Unit". • The new wire should be added to the existing wiring harness as shown by the red line "Picture 1 - Connection from Supercap to Drive Unit". • Z-Splice is the preferred method using A 000 982 91 10. • Crimp Contact Pin (MLK) for the Drive Unit (N145) is A0485450328. NOTE: All WIS instructions must be followed for wiring modifications. Damage code: 0 - 51422 - ** - 7 (for ** please state the following: "missing connection ex factory"). If the vehicle has had the modification completed and returns with an exact matching "complaint", please open a TIPS case.

  Associated Products (7)

  2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11019639-0001.pdf↗
• June 12, 2025•Document ID: 11020009

  Emissions
  ENGINE; ELECTRICAL SYSTEM

  Mfr Comm. #:

  Emissions - 2025040001

  Date Added:

  July 1, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control software might not meet current specifications. As a result, the diagnosis routine for monitoring the air-fuel ratio might not be activated as intended and a malfunction in the oxygen sensor could be erroneously detected causing the “check engine” Malfunction Indicator Lamp (‘MIL’) to illuminate. MBUSA will conduct a voluntary emissions recall. An authorized Mercedes-Benz dealer will update the engine control unit software.

  Associated Products (4)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11020009-0001.pdf↗
• June 9, 2025•Document ID: 11019747

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.15-P-063353

  Date Added:

  June 26, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2. Steering column height adjustment transmission Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Perform software update of driver's seat control unit 2. Replace repair kit for steering column height adjustment Procedure 1: Perform software update of driver seat control unit. ALL models except 205/253/293/222/217/231/463/213/238/257/290 up to special equipment code 801. • Move out the fore/aft adjustment to the end position. • Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward • After releasing the jam, perform a software update of the driver's seat control unit If procedure 1 is not effective, there is no new software available for the driver seat control unit, or the chassis is not listed above (167, 223, 294, 206, 294, 295, 296, 297,232,214,254) then use procedure 2. Procedure 2: Replace repair kit for steering column height adjustment. • Move out the fore/aft adjustment to the end position. • Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward • Remove footwell trim on driver's side. • Determine type version of height adjustment in XENTRY Parts Information and order appropriate replacement part (refer to attachment). 1. Version A: A 231 460 77 00 2. Version B: A 205 460 38 03 • Remove steering column. • Remove height adjustment (adjustment repair kit). • Install repair kit (adjustment repair kit) (observe tightening torque for screws in attachment). • Install steering column. • If possible, flash driver seat control unit to latest software release or code SCN again. • Commission driver seat control unit (normalization of limit stops is deleted and learning process repeated).

  Associated Products (84)

  2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class+ 64 more
  Associated Documents

  • DownloadMC-11019747-0001.pdf↗