Mercedes-Benz C-Class Service Bulletins (2022)

425 manufacturer communications on file.

• February 19, 2025•Document ID: 11014399

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI07.70-P-078547

  Date Added:

  February 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Engine idle fluctuates or stumbles at approximately 7 second interval. No relevant fault codes are stored. If fault codes are stored or check engine light illuminated, this should be diagnosed separately. Cause Torque signal mismatch between MRG and PTCU control units. Only effects version 20B of PTCU. Remedy Software solution in development and LI will be updated once an ETA is available. Replacing parts will not resolve this symptom. Vehicle can be released to owner if there are no other symptoms present. The idle fluctuation typically resolves after several trips and will not cause other drivability symptoms or damage to the vehicle. Create an informational TIPS case and submit to the powertrain team with the below information: -Video showing the "engine data" from head unit while symptom active -N3/10 MRG2 control unit log

  Associated Products (7)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLE-Class
  Associated Documents

  • DownloadMC-11014399-0001.pdf↗
• February 12, 2025•Document ID: 11014255

  Service Bulletin/Repair Instructions
  VISIBILITY/WIPER; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-078762

  Date Added:

  February 14, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Please note that the exact quick test conditions must be met as seen below. If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: • Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. • See attachment "LI Criteria" for an example. • Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

  Associated Products (52)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class+ 32 more
  Associated Documents

  • DownloadMC-11014255-0001.pdf↗
• February 7, 2025•Document ID: 11014606

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA- 24P5497747

  Date Added:

  February 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-25 A-Class, C-Class, CLA, CLS, E-Class, G-Class, GLA, GLB, GLC, GT, and S-Class (118, 177, 205, 213, 217, 222, 238, 247, 253, 257, 290, 463 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. Parts Parts are not required

  Associated Products (58)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT+ 38 more
  Associated Documents

  • DownloadMC-11014606-0001.pdf↗
• February 7, 2025•Document ID: 11014596

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 24P5497745

  Date Added:

  February 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-25 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLB, GLE, GLS, AMG GT 4-Door, and S-Class (118, 167, 177, 205, 213, 222, 238, 243, 247, 257, 290 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

  Associated Products (38)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class+ 18 more
  Associated Documents

  • DownloadMC-11014596-0001.pdf↗
• February 6, 2025•Document ID: 11014223

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI20.10-P-078510

  Date Added:

  February 12, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Red cooling system malfunction warning due to overheat. Low engine performance. Check engine light on. Fault codes may be stored: P21814B The cooling system has a malfunction. There is a fault due to overtemperature. P2B8500 The rpm of the coolant pump is too low. Cause Various Remedy Check for loose plug at electrical connectors of high temp coolant pump (M43/10 or M75/11) by gently pulling on connector housings. Create a TIPS case and submit to powertrain team inbox if a loose plug is found at the coolant pump. Include: -Initial quick test -Details on any damage found to engine or cooling system. Include photos if applicable. -Any other relevant details.

  Associated Products (6)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11014223-0001.pdf↗
• February 3, 2025•Document ID: 11013996

  Service Bulletin/Repair Instructions
  LANE DEPARTURE: ASSIST; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI46.10-P-078012

  Date Added:

  February 7, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the note "reproducible". If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. New coding parameters (SCN) will be available in Q2/2025 for the HOSWD control unit.

  Associated Products (57)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class+ 37 more
  Associated Documents

  • DownloadMC-11013996-0001.pdf↗
• February 3, 2025•Document ID: 11014412

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  February 22, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

  Associated Products (157)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 137 more
  Associated Documents

  • DownloadMC-11014412-0001.pdf↗
• January 31, 2025•Document ID: 11013847

  Other
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  CL - Comm Module OTA

  Date Added:

  February 6, 2025

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC ("MBUSA"), thank you for being a part of the Mercedes-Benz family. We hope that you're enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air ("OTA") Service Campaign to update the communication module software on certain Model Year 2019-2025 A-Class, C-Class, CLA, CLE, CLS, E-Class, EQB, EOE, EQS, G-Class, GLA, GLB, GLC, GLE/GLS, AMG GT 4-Door, and S-Class vehicles. This update includes quality-enhancing optimizations and product improvements.

  Associated Products (49)

  2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz EQB-Class+ 29 more
  Associated Documents

  • DownloadMC-11013847-0001.pdf↗
• January 31, 2025•Document ID: 11013297

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; POWER TRAIN

  Mfr Comm. #:

  LI27.60-P-076554

  Date Added:

  January 31, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint • Hard 1-2 shift • Jerky shifting • Jolting when moving off Cause Insufficient data points for the adaptation limits algorithm Remedy Problem will be rectified with a new SW release Until the SW release is available, (No current ETA) please carry out the following: • Check the transmission oil level and correct if necessary • Rinse the valves a minimum of 3 times via XENTRY • Perform a stationary standstill adaptation, then collect EEPROM data If the problem persists, please perform driving adaptations of 4-5 at least ten to fifteen times: : • Level track (no incline/decline) • Slippery drive program • Display the torque in the instrument cluster: The torque must be between 100 and 250 Nm, preferably closer to the maximum torque • Constant engine torque • Engine speed under 2500 rpm • Do not shift via paddle • Collect a new EEPROM data after all adaptions are complete If the problem persists, please create a TIPS case. With both EEPROM files

  Associated Products (5)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11013297-0001.pdf↗
• January 29, 2025•Document ID: 11013190

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-077250

  Date Added:

  January 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint For the potentially affected vehicles, excessively high aging of the battery was calculated at cold battery temperatures (<50°F) and the MIL activated accordingly, even though there is no corresponding high level of aging physically. In this regard, the fault code P0A7F00 "The age limit of the hybrid/high-voltage battery module has been reached" is displayed in the N127 PTCU control unit and/or A66 battery module control unit (48 V battery). Cause Faulty computation of the age limit of the 48 V battery. Remedy Do not replace any parts!! Step 1: Perform the software update of A66 battery module (48 V battery) After SW has been updated, perform the following reset procedure: Step 1: Read the State of Health Resistance - (SOH-R) Step 2: If SOH-R <=125%: Clear fault memory in PTCU(N127) and 48V battery (A66). Procedure finished. If SOH > 125%: Drive for a duration of 60 minutes to retrain the SOH-R value. Step 3: Read the State of Health Resistance - (SOH-R) If SOH-R <=125%: Clear fault memory in PTCU(N127) and 48V battery (A66). Procedure finished. If SOH > 125%: Park vehicle in Workshop for >12 hours in warm ambient temperature >60F, afterwards drive for a duration of 60 minutes. Step 4: Read the State of Health Resistance - (SOH-R) If SOH-R <=125%: Clear fault memory in PTCU(N127) and 48V battery (A66). Procedure finished. If SOH-R is still >125%, open a TIPS case.

  Associated Products (12)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11013190-0001.pdf↗
• January 28, 2025•Document ID: 11013183

  Service Bulletin/Repair Instructions
  SUSPENSION

  Mfr Comm. #:

  LI33.20-P-078406

  Date Added:

  January 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles in the below FIN range. FIN range up to: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). • NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range above): 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

  Associated Products (73)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class+ 53 more
  Associated Documents

  • DownloadMC-11013183-0001.pdf↗
• January 24, 2025•Document ID: 11013186

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078070

  Date Added:

  January 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint - Digital light pop-up messages (warnings, notes, spotlight and dyn. low beam) appear in the instrument cluster (picture in attachment), even though the same digital light settings are stored in all MBUX profiles Note: The pop-up messages are intended to indicate different settings when changing MBUX profiles Cause - ECU software Remedy - Reset MBUX to manufacturer default settings. Software update available as of December 2024. - A26/17 - MBUX multimedia system (head unit)

  Associated Products (10)

  2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11013186-0001.pdf↗
• January 24, 2025•Document ID: 11013184

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI68.10-P-070572

  Date Added:

  January 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noise from area of instrument panel Noise might occur in the following conditions: - At engine speeds of 1500 rpm to 2000 rpm. - In the speed range up to 45mph - Type of noise: "rattling" / "whirring" / "creaking" Cause Attachment points between strut on shock absorber tower and firewall. Remedy Proceed as described below: 1. Measure the current torque at the rear screws/bolts (strut to bulkhead) and document the result 2. Loosen screw/bolt and move vehicle forwards and backwards approx. 2-3 m (to remove tension) 3. Re-tighten screws/bolts to specified torque (35Nm +/-3.5Nm) 4. Perform test drive and if noise issue is rectified, OK => No further measures required. 5. If the noise complaint is still present after the test drive then measure and document the current torque at the front screws/bolts (strut to spring tower mounting console) 6. Re-tighten to the specified torque value (50Nm+/-5Nm) 7. Perform test drive and if noise issue is rectified, OK => No further measures required. 8. If the noise issue is still present after the test drive, then it is more than likely not related to the mounting of the struts on the body-in-white.

  Associated Products (28)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLC-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLC-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz GLC-Class2019 Mercedes-Benz C-Class2019 Mercedes-Benz E-Class2019 Mercedes-Benz GLC-Class+ 8 more
  Associated Documents

  • DownloadMC-11013184-0001.pdf↗
• January 24, 2025•Document ID: 11013179

  Service Bulletin/Repair Instructions
  FUEL/PROPULSION SYSTEM

  Mfr Comm. #:

  LI47.50-P-078804

  Date Added:

  January 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customer-perceived problem: • Fuel gauge reading implausible • MIL ON (market-dependent) N118/3 Fault codes in control units FSCM_GEN4/5/6 • For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 • For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for the listed fault codes in the FSCM (N118) and document the monitor graphics for the primary/ secondary lever-type sensors.

  Associated Products (57)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLC-Class+ 37 more
  Associated Documents

  • DownloadMC-11013179-0001.pdf↗
• January 24, 2025•Document ID: 11013177

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI07.70-P-078520

  Date Added:

  January 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light on. Engine in limp-home mode. Rough running. Low fuel rail pressure fault code P008700 stored in MRG2 control unit. Additional faults below may be stored in MRG2 control unit: Misfire- P030000, P030100, P030200, P030300, P030400, P030084, P030004 Mixture adaptation- P217800 P218762, P017100, P017200, P217700 Injector malfunction- P02EE00, P02EF00, P02F000, P02F100, P214601, P214901 Cause Gas bubbles forming in low pressure fuel system due to fuel boiling. Remedy C300, CLE300, E350, Model year 2024-2025 GLC300 and GLE350 -Check engine control unit N3/10 for software update. -Proceed with software update if versions 2549032303, 2549032403, 2549032503 or 2549032603 are found. -Clear faults and check for any symptoms on road test 2023 GLC300 and early 2024 GLE350 Check if symptom can be reproduced during normal drive cycle. -If reproducible, diagnose the cause of low pressure in fuel system. -If not reproducible, drain and refill fuel tank with top tier premium gasoline. Clear faults and check vehicle operation. Software solution release for remaining models/model years to prevent fuel boiling in low pressure system ETA in Q1 2025. **Do not replace parts unless clear part malfunction is determined**

  Associated Products (5)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz C-Class2022 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11013177-0001.pdf↗
• January 24, 2025•Document ID: 11013192

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI88.60-P-072093

  Date Added:

  January 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Fuel door may require several attempts to open. Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required.

  Associated Products (113)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class+ 93 more
  Associated Documents

  • DownloadMC-11013192-0001.pdf↗
• January 18, 2025•Document ID: 11013077

  Service Bulletin/Repair Instructions
  ENGINE; FUEL/PROPULSION SYSTEM

  Mfr Comm. #:

  LI07.70-P-078520

  Date Added:

  January 24, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light on. Engine in limp-home mode. Rough running. Low fuel rail pressure fault code P008700 stored in MRG2 control unit. Additional faults below may be stored in MRG2 control unit: Misfire- P030000, P030100, P030200, P030300, P030400, P030084, P030004 Mixture adaptation- P217800 P218762, P017100, P017200, P217700 Injector malfunction- P02EE00, P02EF00, P02F000, P02F100, P214601, P214901 Cause Gas bubbles forming in low pressure fuel system due to fuel boiling. Remedy Model year 2024-2025 GLC300 and GLE350 -Check engine control unit N3/10 for software update. -Proceed with software update if versions 2549032503 or 2549032603 are found. -Clear faults and check for any symptoms on road test For all other models or if software is not found in above steps Check if symptom can be reproduced during normal drive cycle. -If reproducible, diagnose the cause of low pressure in fuel system. -If not reproducible, drain and refill fuel tank with top tier premium gasoline. Clear faults and check vehicle operation. Software solution release for remaining models/model years to prevent fuel boiling in low pressure system ETA in Q1 2025. **Do not replace parts unless clear part malfunction is determined**

  Associated Products (7)

  2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz C-Class2022 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11013077-0001.pdf↗
• January 16, 2025•Document ID: 11013298

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI33.30-P-056665

  Date Added:

  January 31, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (174)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class+ 154 more
  Associated Documents

  • DownloadMC-11013298-0001.pdf↗
• January 16, 2025•Document ID: 11012904

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  January 16, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

  Associated Products (150)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class+ 130 more
  Associated Documents

  • DownloadMC-11012904-0001.pdf↗
• January 15, 2025•Document ID: 11013332

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  January 31, 2025

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (158)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class+ 138 more
  Associated Documents

  • DownloadMC-11013332-0001.pdf↗