Jeep Grand Cherokee Service Bulletins (2017)
352 manufacturer communications on file.
- June 21, 2017•Document ID: 10138863Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 9003357
- Date Added:
- June 4, 2018
- Manufacturer:
- FIAT
SummaryPentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - [email protected] Ron Dallison Cell (248-292-9510) [email protected] Joe Lovell Cell (734) 309-6467 - [email protected] If a response is not received within 15 mins, then proceed with the necessary repair.
Associated Products (57)2017 Chrysler 2002017 Chrysler 3002017 Chrysler 300C2017 Chrysler Pacifica2017 Chrysler Town and Country2017 Dodge Challenger2017 Dodge Charger2017 Dodge Durango2017 Dodge Grand Caravan2017 Dodge Journey2017 Dodge Viper2017 Fiat 124 Spider2017 Fiat 5002017 Fiat 500e2017 Fiat 500X2017 Jeep Cherokee2017 Jeep Compass2017 Jeep Grand Cherokee2017 Jeep Patriot2017 Jeep Renegade+ 37 moreAssociated Documents - June 21, 2017•Document ID: 10138859Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 9003726
- Date Added:
- June 4, 2018
- Manufacturer:
- DODGE
SummaryFuel Tank Before replacing this part due to Hard to Fill condition, check the Fuel Filler Tube for restriction after the second door of the capless unit. Replace the Fuel Filler Tube if the second door of the capless unit does not open properly. Contact Sylvia Lopez at (248) 520-9734 if a Tank needs to be replaced.
Associated Products (2)Associated Documents - June 14, 2017•Document ID: 10219831Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:ACCELERATOR PEDAL
- Mfr Comm. #:
- 9003413
- Date Added:
- September 15, 2022
- Manufacturer:
- JEEP
SummaryAccelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
Associated Products (86)2017 Alfa Romeo Stelvio2017 Chrysler 2002017 Chrysler 3002017 Chrysler 300C2017 Chrysler Pacifica2017 Chrysler Town and Country2017 Dodge Challenger2017 Dodge Charger2017 Dodge Durango2017 Dodge Grand Caravan2017 Dodge Journey2017 Dodge Viper2017 Fiat 124 Spider2017 Fiat 5002017 Fiat 500e2017 Fiat 500X2017 Jeep Cherokee2017 Jeep Compass2017 Jeep Grand Cherokee2017 Jeep Patriot+ 66 moreAssociated Documents - June 14, 2017•Document ID: 10138856Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:ACCELERATOR PEDAL
- Mfr Comm. #:
- 9003413
- Date Added:
- June 4, 2018
- Manufacturer:
- ALFA
SummaryAccelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
Associated Products (85)2017 Chrysler 2002017 Chrysler 3002017 Chrysler 300C2017 Chrysler Pacifica2017 Chrysler Town and Country2017 Dodge Challenger2017 Dodge Charger2017 Dodge Durango2017 Dodge Grand Caravan2017 Dodge Journey2017 Dodge Viper2017 Fiat 124 Spider2017 Fiat 5002017 Fiat 500e2017 Fiat 500X2017 Jeep Cherokee2017 Jeep Compass2017 Jeep Grand Cherokee2017 Jeep Patriot2017 Jeep Renegade+ 65 moreAssociated Documents - June 9, 2017•Document ID: 10219882Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 18-057-17
- Date Added:
- September 15, 2022
- Manufacturer:
- JEEP
SummaryFlash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following software enhancements are available:Allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Improved vehicle acceleration at low speed while towing. Allows transmission gear shifting while in limp-in mode, rather than a fixed gear.
Associated Products (1)Associated Documents - June 9, 2017•Document ID: 10219881Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 21-002-17 REV. A
- Date Added:
- September 15, 2022
- Manufacturer:
- JEEP
SummaryFlash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory:P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. In addition, customers may also experience the following condition:During an engine limp mode condition, the transmission remains in a fixed gear. This update allows transmission gear shifting while in limp-in mode, rather than a fixed gear. Bumps on 2-1 and 6-5 down-shift while braking. This software update also includes an enhancement:Improved 5-4 down-shift.
Associated Products (1)Associated Documents - June 9, 2017•Document ID: 10138907Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 18-057-17
- Date Added:
- June 4, 2018
- Manufacturer:
- JEEP
SummaryFlash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following software enhancements are available:Allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Improved vehicle acceleration at low speed while towing. Allows transmission gear shifting while in limp-in mode, rather than a fixed gear.
Associated Products (1)Associated Documents - June 9, 2017•Document ID: 10138906Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 21-002-17 REV. A
- Date Added:
- June 4, 2018
- Manufacturer:
- JEEP
SummaryFlash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory:P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. In addition, customers may also experience the following condition:During an engine limp mode condition, the transmission remains in a fixed gear. This update allows transmission gear shifting while in limp-in mode, rather than a fixed gear. Bumps on 2-1 and 6-5 down-shift while braking. This software update also includes an enhancement:Improved 5-4 down-shift.
Associated Products (1)Associated Documents - June 7, 2017•Document ID: 10219830Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD WIPER/WASHER
- Mfr Comm. #:
- 9003109
- Date Added:
- September 15, 2022
- Manufacturer:
- RAM
SummaryWasher Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
Associated Products (183)2018 Alfa Romeo 4C2018 Alfa Romeo Stelvio2018 Chrysler 2002018 Chrysler 3002018 Chrysler Pacifica2018 Chrysler Town and Country2018 Dodge Challenger2018 Dodge Charger2018 Dodge Durango2018 Dodge Grand Caravan2018 Dodge Journey2018 Fiat 124 Spider2018 Fiat 5002018 Fiat 500X2018 Jeep Cherokee2018 Jeep Compass2018 Jeep Grand Cherokee2018 Jeep Patriot2018 Jeep Renegade2018 Jeep Wrangler+ 163 moreAssociated Documents - June 7, 2017•Document ID: 10219828Service Bulletin/Repair InstructionsBACK OVER PREVENTION: SENSING SYSTEM: CAMERA
- Mfr Comm. #:
- 9003718
- Date Added:
- September 15, 2022
- Manufacturer:
- JEEP
SummaryRear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
Associated Products (4)Associated Documents - June 7, 2017•Document ID: 10219826Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- 9003530
- Date Added:
- September 15, 2022
- Manufacturer:
- RAM
SummaryBrake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
Associated Products (13)Associated Documents - June 7, 2017•Document ID: 10219825Service Bulletin/Repair InstructionsBACK OVER PREVENTION; ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SENSORS
- Mfr Comm. #:
- 9003624
- Date Added:
- September 15, 2022
- Manufacturer:
- JEEP
SummaryBlind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
Associated Products (2)Associated Documents - June 7, 2017•Document ID: 10138855Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD WIPER/WASHER
- Mfr Comm. #:
- 9003109
- Date Added:
- June 4, 2018
- Manufacturer:
- CHRYSLER
SummaryWasher Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
Associated Products (77)2018 Alfa Romeo Stelvio2018 Chrysler 2002018 Chrysler 3002018 Chrysler Pacifica2018 Dodge Challenger2018 Dodge Charger2018 Dodge Durango2018 Dodge Grand Caravan2018 Dodge Journey2018 Jeep Cherokee2018 Jeep Compass2018 Jeep Grand Cherokee2018 Jeep Renegade2018 Jeep Wrangler2018 Ram 15002018 Ram 25002018 Ram 35002018 Ram 45002018 Ram 55002018 Ram Promaster City+ 57 moreAssociated Documents - June 7, 2017•Document ID: 10138853Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 9003718
- Date Added:
- June 4, 2018
- Manufacturer:
- DODGE
SummaryRear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
Associated Products (4)Associated Documents - June 7, 2017•Document ID: 10138851Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- 9003530
- Date Added:
- June 4, 2018
- Manufacturer:
- JEEP
SummaryBrake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
Associated Products (13)Associated Documents - June 7, 2017•Document ID: 10138850Service Bulletin/Repair InstructionsLANE DEPARTURE: BLIND SPOT DETECTION
- Mfr Comm. #:
- 9003624
- Date Added:
- June 4, 2018
- Manufacturer:
- JEEP
SummaryBlind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
Associated Products (2)Associated Documents - March 31, 2017•Document ID: 10217587Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 21-009-17 REV. A
- Date Added:
- August 8, 2022
- Manufacturer:
- JEEP
SummaryFlash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
Associated Products (2)Associated Documents - March 31, 2017•Document ID: 10217586Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; BACK OVER PREVENTION; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; AIR BAGS
- Mfr Comm. #:
- 18-024-17 REV. A
- Date Added:
- August 8, 2022
- Manufacturer:
- JEEP
SummaryFlash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Associated Products (4)Associated Documents - March 31, 2017•Document ID: 10140055Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 21-009-17 REV. A
- Date Added:
- June 11, 2018
- Manufacturer:
- JEEP
SummaryFlash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
Associated Products (2)Associated Documents - March 31, 2017•Document ID: 10140054Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 18-024-17 REV. A
- Date Added:
- June 11, 2018
- Manufacturer:
- DODGE
SummaryFlash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Associated Products (4)Associated Documents