GMC Yukon Complaints

6,462 consumer complaints on file.

#11760432August 28, 2026
ENGINE
At approximately 58,565 miles, my 2023 GMC Yukon Denali equipped with the 6.2L L87 V8 experienced an internal engine failure. The vehicle had previously completed the applicable L87 engine recall remedy earlier in 2026. The vehicle developed a thumping noise and was inspected by an authorized GMC dealership. The dealer confirmed metal contamination in the engine oil and diagnosed a main thrust bearing failure. The condition was confirmed by the dealer and required complete engine replacement rather than a minor repair. The vehicle was out of service for approximately 31 days while the engine replacement was completed. GM authorized and covered installation of a complete factory replacement engine. The failed engine is available for inspection if requested. The failure created a significant safety concern because an internal engine failure of this type can result in loss of motive power while driving, potentially creating a hazard for the occupants and other motorists. I am aware that NHTSA is currently investigating L87 engine failures occurring after recall remedies. I am submitting this complaint because my vehicle experienced a documented internal engine failure after the vehicle had already received the applicable recall remedy and subsequently required a complete engine replacement. The replacement engine has not currently failed, and I am not reporting a failure of the replacement engine. However, I am concerned about the effectiveness of the remedy and whether the replacement engine incorporates updated or revised components intended to address the underlying failure condition. I have requested documentation from the dealership regarding the exact replacement engine assembly and whether it incorporates engineering or production changes related to the original bearing failure. That information has not yet been provided. No crash or injury occurred as a result of this failure.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760441August 28, 2026
ENGINE
Driving about 75 mph car shuttered and motor quit running had to pull off of the highway and get towed to dealership. Motor had to be replaced due to 1,2,6,7 rod bearings spun on the crankshaft. 34367 miles
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760467August 28, 2026
ENGINE
Driving down the interstate and lost all power, it said start engine and didn’t start coasted to the side of the road. It sounded like locked up engine, confirmed at dealership locked up engine.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760473August 28, 2026
ENGINE
Hello, I own a 2024 GMC Yukon Denali with the 6.2L V8. Car currently has 35,000 miles on it. At about 30,000 miles we started to feel a very aggressive vibration in the passanger seat, as well as the 2nd row seats, and driver seat. We took the vehicle in for the recall on the engine where we were instructed to put 0W-40 oil in. Much higher vescocity. After we did this recall the vehicle has not stopped shaking. We went for another service visit in July where we were told " this is the engine pistons trying to conserve fuel, and are firing causing the vibration." I have worked in the auto industry for 12 years, this is not a normal vibration. This should also not be caused by an engine. We then took it in again where they then proceeded to replace fuel manifold on August 18th. The vehicle shakes a bit less but still has a aggressive shake to it. I do not believe this is normal and if it is the engine pistons firing or the crank shafts misfiring, this could cause the engine to have catistrophic failure. This shake happens at speeds anywhere from 18 MPH to 50 MPH. My concern is with my wife and kids in this vehicle as the daily driver and this engine fails.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760484August 28, 2026
ENGINE
Complete engine failure, recall was performed before engine failed on highway with family inside.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759996August 27, 2026
ENGINE AND ENGINE COOLING
The contact owns a 2021 GMC Yukon. The contact stated that while driving at 70 MPH with family members in the vehicle, the transmission independently shifted into neutral. No warning lights illuminated. The contact was able to steer the vehicle into a residential driveway, where the vehicle failed to restart. The contact requested towing services; however, the initial tow driver failed to arrive after nearly three hours, requiring the contact to call a second tow company. The vehicle was towed to a dealer, where it was diagnosed with engine failure, and it was determined that the engine needed replacement. The vehicle was not repaired, but replacement parts were ordered. The contact associated the failure with NHTSA Campaign Number: 25V274000 (Engine and Engine Cooling). The contact stated that in January 2026, the vehicle was taken to the dealer for the recall repair, but the contact was informed that the vehicle had passed the recall inspection. The manufacturer was notified of the failure, and a case was opened. The manufacturer offered a 90% discount on the repair costs; however, the contact declined the offer and requested a full refund for both towing service fees. The failure mileage was approximately 151,017.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759946August 27, 2026
ENGINE
Engine failure due main bearing and rod failure. Engine had heavy knocking.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760157August 27, 2026
ENGINE
My vehicle is making a knocking sound and has the L87 6.2 V8 engine that is under recall for catastrophic failure. It has been evaluated by 2 mechanics that say it needs a new engine. Yes it is available for inspection upon request. Although it has not shutdown yet, both mechanics have said it is eventually going to be a catastrophic failure. My safety and families safety is at risk of it shuts down and causes an accident. There is no warning light currently displayed.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760143August 27, 2026
ENGINE
Once we learned about the 6.2L Engine Failure we took the vehicle to Mckinney GMC in [XXX], test were run and were told the engine needed to be replaced, but would take several months to repair. We could not wait months for the vehicle so we had the vehicle towed to Sewell GMC in [XXX] (we bought the vehicle CPO from there) they ran test and said we didn't need a new engine but that they would just replace the oil weight and it would be fine. The engine has not run right since, it shakes and idles hard, and was never given a clear answer as to how metal shavings were found in the oil at McKinney GMC but magically disappeared at the Sewell dealership. Its very unsettling that at any moment while driving the engine could seize and blow. I feel like we have a lemon vehicle and the oil weight change is simply a band aid for this situation. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760118August 27, 2026
ENGINE, ELECTRICAL SYSTEM, FUEL/PROPULSION SYSTEM
This vehicle has been towed into GMC service 3 times to date. #1. 2/2024 (mil 22,662) would not start, low voltage msg, replaced battery. #2. 4/2026 (mil 57,854) vehicle went into N on its own while I was driving down the road, msg on dash "function not available", I stopped and the engine died & would not restart, no engagement from starter motor, found P0615 present, found blown fuse on battery distribution fuse block, replaced. #3. 7/2026 (mil 63,041) vehicle went into N on its own while I was driving down interstate, msg on dash "function not available", I stopped, the engine died and would not restart, found main battery fuse blown, engine seized, found spun rod bearing full of metal debris, replaced engine, radiator, cooler lines, seals, gaskets, bolts, & fluids. My safety was at risk as I was driving down a highway and the interstate 2 of the times the vehicle put itself in N. The problem has been confirmed by the dealer. The vehicle has been inspected by the dealer's service dept. Prior to these incidents I did not notice any symptoms that would have alerted me of what was to come. **This report is referring to my latest incident which was engine seizure. *Two recalls have been performed, #1. 5/2025 "reprogrammed serial data module" & #2. 11/2025 "engine loss of propulsion recall", replaced oil with 0W-40 & "ECM software update recall", replaced ECM with SPS.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11760082August 27, 2026
ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN
My 2023 GMC Yukon AT4 with the 6.2L V8 has experienced multiple serious engine-related failures. The original engine previously was making a whining / knocking noise, then seized and required complete engine replacement under a GM recall/campaign involving 6.2L engine failures. The replacement engine later developed a lifter/valvetrain failure and required lifter replacement. The vehicle is now again exhibiting a pronounced rhythmic mechanical knocking/tapping noise, primarily during cold starts after sitting for an extended period. The noise occurs on most cold starts and has been documented in multiple videos. The vehicle is currently at a GMC dealership for inspection. I provided the dealer with several videos clearly demonstrating the noise. The dealer has stated that it has not yet been able to reproduce the condition and is attempting additional cold-start testing. The exact cause is currently UNKNOWN. No consistent warning lights or dashboard messages have appeared with the current knocking condition. My concern is that this vehicle has already experienced a catastrophic engine seizure, followed by internal valvetrain/lifter failure in the replacement engine, and is now again exhibiting abnormal mechanical engine noise. I am concerned this may indicate another developing internal engine failure that could potentially result in engine seizure or sudden loss of power while driving, including at highway speeds or in traffic. The vehicle and engine remain available for inspection, and multiple video recordings of the recurring cold-start knocking are available.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759987August 27, 2026
POWER TRAIN
The powertrain malfunctioned and it at the dealership for an engine replacement. The vehicle lost propulsion on a 2-lane road while passing another vehicle. It cut off completely and started to decelerate. There was no warning or indication that this would happen and was dangerous in that I was accelerating to pass another vehicle when the event occurred. I was able to safely pull into a driveway, but the vehicle would not crank as it could not detect what gear it should be in. It was towed to a GMC dealership locally who confirmed 2 days later that the engine would have to be replaced. It is under warranty and will take 3-4 weeks.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759923August 27, 2026
ENGINE
As my wife was driven she heard some noise and notice she was losing power. She pull off the side of the road and the car shut off. Could not restart. This happen about 11:30 am on 8/14/26 Got towed to Salida Dealer called Faricy GMC about 3:30 pm. Dealer said it was a complete engine failure and engine needed to be replaced.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759661August 26, 2026
ENGINE
The contact owns a 2026 GMC Yukon. The contact stated that while driving approximately 15-20 MPH and approaching a stop in Nebraska, there was an abnormal sound coming from the vehicle. The vehicle was shaking and vibrating abnormally. The contact called the local dealer, and an appointment was scheduled. The failures persisted while waiting for the appointment. While driving at an undisclosed speed, the vehicle lost motive power and stalled. The driver alerted OnStar about the failure. The vehicle failed to restart. The vehicle was towed to the local dealer, where it was diagnosed with complete engine failure. The contact was informed that the engine needed to be replaced. The vehicle was repaired; however, the contact no longer wanted the vehicle. The manufacturer was contacted and opened a case and escalated the concerns. The failure mileage was approximately 4,700.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759643August 26, 2026
FUEL/PROPULSION SYSTEM, ELECTRICAL SYSTEM
1. What component or system failed or malfunctioned. The Fuel Pump Module failed unexpectedly while the vehicle was being driven. Failure caused the engine to stall, resulting in a complete loss of power and mobility. Unsure if part is available for inspection. 2021 GMC Yukon have a recall N252516900, but our VIN is not included in this. Can our VIN be added to this recall please? 2. How was your safety or the safety of others put at risk? The vehicle abruptly stalled while being driven through a parking lot, causing a complete loss of power and leaving the vehicle disabled in an active traffic area. Because the vehicle could not be shifted out of PARK, it became an obstruction, creating a hazard for other drivers navigating the parking lot and increasing the risk of a collision. 3. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes. After the vehicle was towed to a local mechanic on a flatbed truck, the dealer diagnosed and confirmed that the Fuel Pump Module had failed, which caused the vehicle to stall and lose power. 4. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? The vehicle was inspected by a local repair shot, which diagnosed the failed Fuel Pump Module. The vehicle was also evaluated during the towing process. To my knowledge, the manufacturer, police, or insurance representatives have not separately inspected the vehicle or component. 5. Were there any warning lamps, messages, or other symptoms of the problem prior to the failure, and when did they first appear? Prior to the failure, there were no significant symptoms indicating an imminent fuel system failure. When the incident occurred, the vehicle abruptly stalled, lost all power, and displayed a message indicating that the vehicle was "not in a condition to shift," preventing it from being shifted out of PARK. This message first appeared immediately following event.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759639August 26, 2026
ENGINE, ENGINE AND ENGINE COOLING
The contact owns a 2024 GMC Yukon. The contact stated that while her husband was driving at approximately 45–50 MPH, the vehicle stalled. No warning light was illuminated. The driver pulled over to the side of the road, and the vehicle was towed to the dealer, where it remained for five weeks before being diagnosed. The dealer determined that the engine was blown and needed to be replaced. The vehicle was repaired at the owner's expense. The contact associated the failure with NHTSA Action Number: EA25007 (Engine, Engine and Engine Cooling). The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 63,073.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759549August 25, 2026
ENGINE
Engine locked up and seized traveling 75mph on interstate with only 28,000 miles
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759547August 25, 2026
ENGINE
Vehicle became disabled. GM service center determined that the crankshaft failed and lifter rods bent causing total engine failure. GM service center unable to determine cause and the engine is being replaced at a significant out of pocket cost.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759361August 25, 2026
ENGINE, FUEL/PROPULSION SYSTEM, ELECTRICAL SYSTEM
This is a supplemental report to my original complaint (NHTSA ID XXX) regarding my 2024 GMC Yukon (VIN [XXX]). I am providing additional detail: prior to GM's recall being issued, I contacted Hatchett Buick GMC by phone and visited in person on multiple occasions reporting engine sputtering, stalling, hesitation, and total loss of power and electrical shutdown while driving. I was repeatedly told these were minor issues not affecting anyone and not to worry about them. As a result, the vehicle was not formally serviced for these issues until September 2025 — roughly three months after the recall was finally announced, more than a year after I purchased the vehicle. Since that recall repair and a subsequent "best guess" repair performed by GM technicians (their own description, not mine), the vehicle continues to sputter, hesitate, stall, and intermittently lose power. I have ongoing safety concerns driving this vehicle INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11759054August 24, 2026
SERVICE BRAKES, HYDRAULIC
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that there was an abnormal sound coming from the vehicle and the ABS warning light was illuminated. The contact stated that after several attempts, the vehicle stopped. The vehicle was taken to the dealer; however, the vehicle was waiting to be inspected. The contact stated that an unknown recall repair with a similar description was completed in 2024; however, the contact was informed that the repair was not covered under warranty. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 136,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to GMC Yukon