BMW ActiveHybrid 3 Service Bulletins
601 manufacturer communications on file.
- September 1, 2015•Document ID: 10147262Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryIHKA - Recirculation Function Changes from Manual to Automatic. While driving, the air recirculation button on IHKA changes by itself from manual to automatic or automatic to manual mode. CAUSE The IHKA operating software is too sensitive.
Associated Products (34)Associated Documents - September 1, 2015•Document ID: 10147259Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:BACK UP LIGHTS
- Mfr Comm. #:
- B630515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Reverse Light is Intermittently Inoperative. CCM (Check control message) is displayed indicating a ""reverse light"" is out. CAUSE There is a weak spring in bulb socket or bulb carrier (on the luggage compartment lid) which is causing a bad contact with the bulb."
Associated Products (24)Associated Documents - September 1, 2015•Document ID: 10147251Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- B512615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDriver or Passenger's Front Doors Handles Inoperable. Sporadically it is not possible to open the driver or passenger's front door from the outside or inside door handle. Multiple attempts will eventually open the door. Comfort access operation of the outside door handle works properly. This situation occurs at temperatures below 37 °F. CAUSE Incorrect routing of the Bowden cable.
Associated Products (24)Associated Documents - September 1, 2015•Document ID: 10147243Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- B360115
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCheck Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Associated Products (49)Associated Documents - September 1, 2015•Document ID: 10147242Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC
- Mfr Comm. #:
- B340414
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Associated Products (100)Associated Documents - September 1, 2015•Document ID: 10147241Service Bulletin/Repair InstructionsWHEELS; POWER TRAIN:DRIVELINE
- Mfr Comm. #:
- B270415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryShudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Associated Products (176)Associated Documents - September 1, 2015•Document ID: 10147240Service Bulletin/Repair InstructionsPOWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- B240712
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This Service Information bulletin supersedes SI B24 07 12 dated November 2012 SUBJECT Hybrid Automatic Transmission: Fluid Maintenance Service Interval. INFORMATION Only properly trained personnel, who have passed all applicable technical training courses, should perform any maintenance or repairs on any Hybrid or Electric Vehicle. Work performed by unqualified persons may result in severe injury or damage to the vehicle. Additional information may be found in REP 61 00... Observe safety instructions when handling electric vehicles. This requirement is due to the hybrid-specific components that are contained in the transmission. Refer to Repair Instruction 00 00 630, ""Automatic transmission fluid service (GA8P70Z) N55 hybrid,"" for the proper servicing procedure. Refer to SI B00 09 12 for BMW Maintenance Program claim-related information."
Associated Products (8)Associated Documents - September 1, 2015•Document ID: 10147235Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE
- Mfr Comm. #:
- B111615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
Associated Products (73)Associated Documents - August 1, 2015•Document ID: 10151415Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- B620515
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"Instrument Cluster: CBS ""Running-in Check"" is Displayed. After replacing and / or programming the instrument cluster with ISTA/P 3.55.0 or higher (integration Level F020-15-03-501 or higher), the CBS (Condition Based Service) displays ""running-in check"" or ""1200 mile service is due"". The parameters of the CBS scopes for oil service, brake fluid, etc, can also be implausible or invalid. CAUSE Error in the CBS mapping data in the FEM (Front Electronics Module) and corrupt data in the instrument cluster during programming."
Associated Products (34)Associated Documents - August 1, 2015•Document ID: 10151404Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B270315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryVibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
Associated Products (142)Associated Documents - August 1, 2015•Document ID: 10151399Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryThe plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
Associated Products (67)Associated Documents - July 1, 2015•Document ID: 10147211Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- B651015
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryNAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
Associated Products (132)Associated Documents - July 1, 2015•Document ID: 10147204Service Bulletin/Repair InstructionsEQUIPMENT; VISIBILITY:WINDSHIELD WIPER/WASHER; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN
- Mfr Comm. #:
- B610415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryHorn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
Associated Products (32)Associated Documents - July 1, 2015•Document ID: 10147202Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:LABELS
- Mfr Comm. #:
- B511615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
Associated Products (143)Associated Documents - July 1, 2015•Document ID: 10147200Service Bulletin/Repair InstructionsPOWER TRAIN:AXLE ASSEMBLY; WHEELS:HUB; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC
- Mfr Comm. #:
- B340814
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryTicking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
Associated Products (42)Associated Documents - July 1, 2015•Document ID: 10147198Service Bulletin/Repair InstructionsSTRUCTURE; POWER TRAIN
- Mfr Comm. #:
- B330115
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCracking in Rear Differential Mount Bushing. During inspection, the rear differential mount in the rear axle support shows signs of cracking.
Associated Products (60)Associated Documents - July 1, 2015•Document ID: 10147197Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC:POWER ASSIST; STEERING; STEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING:HYDRAULIC POWER ASSIST SYSTEM
- Mfr Comm. #:
- B320314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryPower-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues. The following codes may be stored in the fault memory of the Electric Power Steering (EPS): Scenario 1: 0x4823E1 Scenario 2: 0x4823CB/0x4823CC Scenario 3: 0x4823D2 and/or 0x4823EC Scenario 4: 0x48239C (DSC warning lamp lights up in the instrument cluster) Scenario 5: No communication with the EPS is possible (not accessible using diagnostics) Scenario 6: 0x4823EE and 0x4823C2
Associated Products (38)Associated Documents - July 1, 2015•Document ID: 10147192Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- B130215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."
Associated Products (96)Associated Documents - July 1, 2015•Document ID: 10147189Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryEngine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (74)Associated Documents - July 1, 2015•Document ID: 10146945Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; EQUIPMENT
- Mfr Comm. #:
- B111315
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryThe plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
Associated Products (67)Associated Documents