BMW 335is Service Bulletins (2013)
120 manufacturer communications on file.
- February 1, 2015•Document ID: 10147067Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - February 1, 2015•Document ID: 10057707Service Bulletin/Repair InstructionsAIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE; INTERIOR LIGHTING
- Mfr Comm. #:
- SI B65 04 14
- Date Added:
- June 22, 2015
- Manufacturer:
- BMW
SummaryBMW:SOME BMW MODELS MAY OR MAY NOT DISPLAY AIRBAG WARNING LIGHT. *TA
Associated Products (39)Associated Documents - January 1, 2015•Document ID: 10147624Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 651009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (222)Associated Documents - January 1, 2015•Document ID: 10147623Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 650509
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
Associated Products (216)Associated Documents - January 1, 2015•Document ID: 10147595Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- 120415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
Associated Products (191)Associated Documents - December 1, 2014•Document ID: 10148194Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840412
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
Associated Products (204)Associated Documents - October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149361Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 280114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDCT Transmission: Oil Leakage Diagnosis. INFORMATION Incorrect diagnosis of DCT (Double-clutch Transmission) oil leaks may lead to unnecessary part replacements and repeat customer repair visits. When diagnosing complaints related to DCT fluid leaks, please use the attached diagnostic procedure. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B280114_DCT_Oil_Leak_Diagnosis. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16672.2.B28011... 12/24/2014
Associated Products (63)Associated Documents - October 1, 2014•Document ID: 10149286Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 120212
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryINFORMATION This section only applies to vehicles that require cleaning the intake valve and intake ports. Refer to the applicable Service Information bulletin or ETK if carbon cleaning was not the root cause for the complaint. Reuse the strut brace bolts. Part Number Carbon Blaster Walnut Shells: Replacement media, 20/30 SAE or 0.45-0.80 mm walnut shells can be sourced locally or through one of the following distributors: MARCO(r) Corporate - (800) 252-7848, ext. 284 - marcousa.com/index.cfm Trinity Tool Company - (800) 587-4626 - www.trinco.com McMASTER-CARR(r) - www.mcmaster.com Refer to EPC for applicable gaskets and bolts.
Associated Products (31)Associated Documents - October 1, 2014•Document ID: 10149279Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 070314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - October 1, 2014•Document ID: 10057568Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH
- Mfr Comm. #:
- SIB-63-11-14
- Date Added:
- June 10, 2015
- Manufacturer:
- BMW
SummaryBMW: ON SOME VEHICLES, WHEN STARTING, LOW BEAM, WITH 0552 OPTION, WOULD BRIEFLY FLASHES, DUE TO A FAULTY LED MAIN LIGHT MODULE THAT NEEDS REPLACING. MODEL 2008-14 F01, F02, F06, F07, F10, F12, F13, F25. *PE
Associated Products (95)Associated Documents - September 1, 2014•Document ID: 10148034Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 611714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor, function c. 2E8D - Intelligent battery sensor, signal transmission d. 2E8E - Intelligent battery sensor, communication CAUSE A faulty battery or IBS sensor (not both) The power management system and IBS in the vehicle cannot determine if the battery needs to be replaced. This is normal operation for all E-Series vehicles because they do not have the Advanced IBS sensor that the F-Series vehicles do. An external battery tester (Midtronics EXP-1000) must be used to determine if the battery needs to be replaced. Energy Diagnosis will not prompt for a battery replacement unless the battery is ""aged."" When energy diagnosis identifies the battery as ""aged,"" it means the amount of energy discharge over the course of the life of the battery has reached its maximum (worn out). In most cases, energy diagnosis states that the battery is OK. This is typically an indication of the current State of Charge (SoC), not the State of Health (SoH). The SoC is defined as the current amount of energy left in the battery (displayed as a percentage). The SoH is defined as an evaluation of the condition of the battery over a period of time (displayed as a percentage). For more information about batteries, refer to Training Manual ST051, ""07 Battery Basics."""
Associated Products (118)Associated Documents - July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - July 1, 2014•Document ID: 10148087Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 010414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryExternal Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
Associated Products (126)Associated Documents - June 1, 2014•Document ID: 10148101Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Associated Products (215)Associated Documents - May 1, 2014•Document ID: 10148328Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; STRUCTURE:BODY:ROOF AND PILLARS
- Mfr Comm. #:
- 540908
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCleaning Excess Butyl from RHT Roof Shells. Butyl adhesive is used to secure the seals of the retractable hardtop (RHT) to the steel roof shell panels. Particularly at high ambient temperatures, if excess butyl is present, it may start to seep out from between the seal and the roof shell. This butyl may be black or gray in color. Excess butyl applied to the roof shell during assembly
Associated Products (18)Associated Documents - May 1, 2014•Document ID: 10148320Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- 360309
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThird Generation Tire Pressure Monitor System (RDC). INFORMATION As of September 2009 production, a new generation Tire Pressure Monitor System has been introduced for all 3 Series models. Although the basic operation of the system is similar to the previous version, there are several key differences between the two systems. The new system consists of five components: One central antennae with an integrated control module (5) mounted in the right rear wheel arch Four wheel electronics (1-4) mounted at the base of each tire valve. Central antennae with integrated control module The control module and central antennae have been combined in a single housing. This new control module has the ability to send requests for information to each of the 4 wheel New style wheel electronics The wheel electronics consist of a plastic housing with integrated circuitry. The following items are contained within the wheel electronics: Pressure sensor Temperature sensor Acceleration sensor Transmitter/receiver unit Self-diagnosis controller Battery The following points should be considered when diagnosing and/or servicing the system: * The system components are not interchangeable or compatible with previous versions. * The type of wheel electronic fitted can only be determined via visual inspection. * The detection of low tire pressure and the subsequent warning is similar to the previous design. * The reset procedure has changed. Special Note for Reset Procedure After initiating a reset, the vehicle must be driven for a period longer than 12 minutes with a vehicle speed which exceeds 19 mph (~30 km/h). WARRANTY INFORMATION Not applicable.
Associated Products (39)Associated Documents - May 1, 2014•Document ID: 10148318Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- 360211
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTire Pressure Monitor System (TPMS) Functional Changes. INFORMATION There has been a disruption in the production and supply chain of certain electronic components. These events have influenced global manufacturing facilities, including the automotive sector. In order to fulfill customer demand and maintain production schedules, BMW has made a change to the Tire Pressure Monitor System of certain vehicles. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16234.2.B360211.... 6/8/2014 Page 2 of 2 Although the basic system operation and function remain the same, changes have been made to the vehicle's display elements when a low tire pressure condition occurs. The following points apply to vehicles produced during the period listed above: * The Tire Pressure Monitor System continues to meet all federal requirements. * When a low tire pressure condition is detected, a general system warning is issued. The warning will be displayed in the instrument cluster (KOMBI) and/or Control Display, depending on the vehicle's equipment level (refer to the attachment). * When a driver is alerted to a low pressure condition, all four tires should be inspected for damage and proper inflation. The system components, wheel electronics and central antennae/module are fully compatible with current replacement parts. This functional change represents a running production change and is not a defect in materials or workmanship. Any further changes to the system function or components will be communicated in a future bulletin. It is imperative that all service personnel be familiar with these changes. WARRANTY INFORMATION Not applicable.
Associated Products (49)Associated Documents - May 1, 2014•Document ID: 10148316Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
- Mfr Comm. #:
- 340313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
Associated Products (53)Associated Documents