BMW 335i Service Bulletins
690 manufacturer communications on file.
- April 1, 2013•Document ID: 10149493Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 710113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryPERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a recall campaign is announced by BMW NA, centers must ensure that all recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. SUBJECT Voluntary Emissions Recall Campaign 13E-A02: Replace Emissions Label. Certain vehicles were produced without the required emissions label installed on the underside of the engine hood. Customers will receive notification letters informing them to make a service appointment at their BMW centers to have the correct label installed.
Associated Products (10)Associated Documents - April 1, 2013•Document ID: 10149492Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 660213
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryRear-view Camera Does Not Turn On Automatically. When the reverse gear is selected, the rear-view camera does not turn on automatically. The driver must activate the rear-view camera using the iDrive controller or the camera button. CAUSE Software error in the Front Electronics Module (FEM)
Associated Products (11)Associated Documents - April 1, 2013•Document ID: 10149490Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651012
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Headunit-Basic: CID is blank and ""NO SIGNAL"" is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-B Error in the Headunit-Basic (HU-B), also called Radio Professional or ENTRY head unit."
Associated Products (6)Associated Documents - April 1, 2013•Document ID: 10149344Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES
- Mfr Comm. #:
- 511511
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadlight Washer Nozzle Cover Sticks Out.
Associated Products (29)Associated Documents - April 1, 2013•Document ID: 10149339Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 121412
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary?SI B12 14 12 April 2013 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 14 12 dated January 2013. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
Associated Products (23)Associated Documents - April 1, 2013•Document ID: 10149338Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 120912
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIntermittently, the engine idle speed may fluctuate up and down or cut off under any of the following circumstances, without any relevant faults stored in the DME memory: * While driving off throttle (coasting) and braking at speeds below approx. 10 mph * While idling, low-speed maneuvering such as parking, or if the steering is turned to the full-lock position Unfavorable DME software
Associated Products (23)Associated Documents - April 1, 2013•Document ID: 10149336Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 120113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Transmission Intermittently Goes into ""P"" or ""N"" after MSA Engine Start. The transmission can intermittently go into the Park (P) or Neutral (N) position after an MSA engine start without any customer influence. This problem is very sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software"
Associated Products (16)Associated Documents - March 1, 2013•Document ID: 10150133Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 651310
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIn all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
Associated Products (57)Associated Documents - March 1, 2013•Document ID: 10150131Service Bulletin/Repair InstructionsAIR BAGS:SENSOR:OCCUPANT CLASSIFICATION; AIR BAGS
- Mfr Comm. #:
- 651013
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Enabling and Replacing New OC3 Seat Mat. The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it."
Associated Products (51)Associated Documents - March 1, 2013•Document ID: 10150130Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 651009
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (173)Associated Documents - March 1, 2013•Document ID: 10150128Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 650513
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryBasic SVS: Voice Recognition Inoperative After Programming. After programming the vehicle with ISTA/P 2.48.x, the voice recognition (Basic SVS) is inoperative. NOTE: The Basic SVS only includes voice recognition for phone functions. Error in the coding data of ISTA/P 2.48.x The voice recognition function is unintentionally deactivated.
Associated Products (32)Associated Documents - March 1, 2013•Document ID: 10150114Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610211
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryAdvanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (State of Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
Associated Products (68)Associated Documents - March 1, 2013•Document ID: 10150112Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 540412
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryRetractable Hard Top (RHT) Is Not Stacking Properly - Frame Bent. The RHT frame is bent or twisted and cannot be operated in either direction, or the roof shells are not stacking properly. The hydraulic roof cylinders operate out of sequence causing the frame to twist.
Associated Products (15)Associated Documents - March 1, 2013•Document ID: 10150108Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340313
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summaryncorrect Remaining Service Life from CBS Data for Brake pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation in the brake pad wear model
Associated Products (6)Associated Documents - March 1, 2013•Document ID: 10150102Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 170113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Coolant Expansion Tank. The low coolant level warning may come on in the information display. CAUSE Insufficient contact at the electrical connector for the coolant level sensor causes an inaccurate reading of the coolant level.
Associated Products (11)Associated Documents - March 1, 2013•Document ID: 10150100Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130409
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (?wet?) with fuel, while the injector tips are covered with a layer of carbon deposit.
Associated Products (31)Associated Documents - March 1, 2013•Document ID: 10150099Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- 130213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
Associated Products (118)Associated Documents - March 1, 2013•Document ID: 10150096Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE
- Mfr Comm. #:
- 121611
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
Associated Products (134)Associated Documents - March 1, 2013•Document ID: 10038217Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
- Mfr Comm. #:
- SIB-11-03-08
- Date Added:
- June 11, 2011
- Manufacturer:
- BMW
SummaryBMW: CRANKCASE PRESSURE DIAGNOSIS AND INFORMATION FOR ALL VEHICLES. *RM UPDATED ON 4/24/2013. *KB
Associated Products (97)Associated Documents - February 1, 2013•Document ID: 10149460Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Roadside Assistance and BMW Online Services Inoperative After Programming. Roadside Assistance and BMW Online services are inoperative after programming the vehicle with ISTA/P 2.48 or higher. The symptoms are as follows: * BMW Online - No network available when selected * Roadside Assistance - When selected, a message stating "Service not enabled or contract expired" is displayed. Also, "Start service" is grayed out and cannot be selected. CAUSE Software error in the CIC (Car Information Computer)"
Associated Products (34)Associated Documents