BMW 335i Service Bulletins (2012)
556 manufacturer communications on file.
- August 1, 2014•Document ID: 10148381Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:LABELS; ENGINE AND ENGINE COOLING:ENGINE:DIESEL
- Mfr Comm. #:
- 710214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
Associated Products (66)Associated Documents - August 1, 2014•Document ID: 10148375Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryA/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
Associated Products (13)Associated Documents - August 1, 2014•Document ID: 10148373Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 620214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHead-Up Display Inoperative. The Head-up Display is inoperative. Fault code 0xB7F6E3 - HUD: Communication error (HUD does not answer) is stored in the Instrument Cluster (KOMB25). A software error in the instrument cluster prevents the Head-up Display from activating.
Associated Products (20)Associated Documents - August 1, 2014•Document ID: 10148371Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM:STARTER ASSEMBLY
- Mfr Comm. #:
- 612014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryVehicle Only Starts when Remote Key Held Against Column. The vehicle does not start using the Comfort Start feature. The vehicle does start once the remote key is held next to the steering column emergency start area (key symbol at the right side of the column between the white marks). The antenna (aerial) in the passenger compartment near the front of the center console has shorted wiring.
Associated Products (16)Associated Documents - August 1, 2014•Document ID: 10148218Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Injector Replacement. INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this problem.
Associated Products (58)Associated Documents - July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148132Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE
- Mfr Comm. #:
- 660414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
Associated Products (94)Associated Documents - July 1, 2014•Document ID: 10148128Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
Associated Products (81)Associated Documents - July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - July 1, 2014•Document ID: 10148117Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 180114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryExhaust Leak on Diesel Particulate Filters. An exhaust leak develops on the Diesel Particulate Filter (DPF) around the area of the flexible coupling. Age or wear on the flexible coupling
Associated Products (16)Associated Documents - July 1, 2014•Document ID: 10148087Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 010414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryExternal Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
Associated Products (126)Associated Documents - June 1, 2014•Document ID: 10148101Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Associated Products (215)Associated Documents - June 1, 2014•Document ID: 10148097Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 510614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Repair Corrosion Protection Engine Compartment. Various engine compartment battery cable mounting points are not sufficiently protected against corrosion. Lack of corrosion protection can lead to improper connections associated with the battery cables. AFFECTED VEHICLES This Service Action involves F30 3 Series vehicles produced from June 2012 to January 2013. First check if a Service Action label with a code number 670 is already attached to the B-pillar. If a code number 670 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
Associated Products (11)Associated Documents - May 1, 2014•Document ID: 10148334Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 630814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryActive Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. Fault Code 8041B6 is present. Broken mounting bolt holding on the rear height sensor bracket.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148333Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
Associated Products (79)Associated Documents - May 1, 2014•Document ID: 10148328Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; STRUCTURE:BODY:ROOF AND PILLARS
- Mfr Comm. #:
- 540908
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCleaning Excess Butyl from RHT Roof Shells. Butyl adhesive is used to secure the seals of the retractable hardtop (RHT) to the steel roof shell panels. Particularly at high ambient temperatures, if excess butyl is present, it may start to seep out from between the seal and the roof shell. This butyl may be black or gray in color. Excess butyl applied to the roof shell during assembly
Associated Products (18)Associated Documents - May 1, 2014•Document ID: 10148323Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK; STRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- 511314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTrunk Lid Does Not Open Completely. The customer may complain that the trunk does not open fully when using the remote key or hands-free trunk-lid opening (a Comfort Access function). CAUSE * A dry trunk lid seal causes the trunk lid to stick. * F30 and F32 only: A trunk return spring that is not installed correctly may not open the trunk lid fully.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148321Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMF56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand. In a continuing effort to maintain the utmost in Motorer satisfaction, MINI USA is offering our dealer partners an alternative solution, the "Make Good" program. For all affected MINI F56 vehicles: * Produced from May 1, 2014 to June 30, 2014 and * Built without the factory order "Contrasting Roof and Mirror Caps" option (382 and 383) Your MINI dealer can offer these Motorers the installation of an accessory roof graphic or set of mirror caps. The Motorer has the choice of either the accessory roof graphic or exterior mirror caps, not both. MINI Area Manager (AM) "Field Authorization" (FAS) is not required. Note: For eligible vehicles (VINs) that are affected by this production restriction, the procedure outlined in this bulletin only applies to mirror caps or roof graphics installed by your dealer. Mirror caps or roof graphics installed through the MINI USA "VIA" (VDC-Installed Accessory) program are not eligible for reimbursement through this Make Good Program.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148320Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- 360309
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThird Generation Tire Pressure Monitor System (RDC). INFORMATION As of September 2009 production, a new generation Tire Pressure Monitor System has been introduced for all 3 Series models. Although the basic operation of the system is similar to the previous version, there are several key differences between the two systems. The new system consists of five components: One central antennae with an integrated control module (5) mounted in the right rear wheel arch Four wheel electronics (1-4) mounted at the base of each tire valve. Central antennae with integrated control module The control module and central antennae have been combined in a single housing. This new control module has the ability to send requests for information to each of the 4 wheel New style wheel electronics The wheel electronics consist of a plastic housing with integrated circuitry. The following items are contained within the wheel electronics: Pressure sensor Temperature sensor Acceleration sensor Transmitter/receiver unit Self-diagnosis controller Battery The following points should be considered when diagnosing and/or servicing the system: * The system components are not interchangeable or compatible with previous versions. * The type of wheel electronic fitted can only be determined via visual inspection. * The detection of low tire pressure and the subsequent warning is similar to the previous design. * The reset procedure has changed. Special Note for Reset Procedure After initiating a reset, the vehicle must be driven for a period longer than 12 minutes with a vehicle speed which exceeds 19 mph (~30 km/h). WARRANTY INFORMATION Not applicable.
Associated Products (39)Associated Documents - May 1, 2014•Document ID: 10148318Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- 360211
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTire Pressure Monitor System (TPMS) Functional Changes. INFORMATION There has been a disruption in the production and supply chain of certain electronic components. These events have influenced global manufacturing facilities, including the automotive sector. In order to fulfill customer demand and maintain production schedules, BMW has made a change to the Tire Pressure Monitor System of certain vehicles. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16234.2.B360211.... 6/8/2014 Page 2 of 2 Although the basic system operation and function remain the same, changes have been made to the vehicle's display elements when a low tire pressure condition occurs. The following points apply to vehicles produced during the period listed above: * The Tire Pressure Monitor System continues to meet all federal requirements. * When a low tire pressure condition is detected, a general system warning is issued. The warning will be displayed in the instrument cluster (KOMBI) and/or Control Display, depending on the vehicle's equipment level (refer to the attachment). * When a driver is alerted to a low pressure condition, all four tires should be inspected for damage and proper inflation. The system components, wheel electronics and central antennae/module are fully compatible with current replacement parts. This functional change represents a running production change and is not a defect in materials or workmanship. Any further changes to the system function or components will be communicated in a future bulletin. It is imperative that all service personnel be familiar with these changes. WARRANTY INFORMATION Not applicable.
Associated Products (49)Associated Documents