2023-2024 BMW Camera Wash Function Not Starting SIB 66 04 24
BMW Service Information Bulletin (SIB) 66 04 24 addresses an issue where the front or rear autonomous camera wash function cannot be started in certain 2023-2024 BMW 5 Series, 7 Series, iX, and X2 models. This is often due to air in the system or unfavorable Basic Central Platform (BCP) software.
Marcus Weber2024 BMW 530i
Also applies to
- BMW 740i
- 2024
- BMW iX
- 2024
- BMW X2
- 2023
BMW has released Service Information Bulletin (SIB) 66 04 24 to address a concern where the "FRONT OR REAR AUTONOMOUS CAMERA WASH FUNCTION CANNOT BE STARTED" message appears. This issue affects various 2023-2024 BMW models equipped with specific parking assistant options. The bulletin outlines a software update and a specific service function to resolve the problem.
Symptoms
Owners may notice that the front or rear autonomous camera wash function is not starting. This can occur if air remains in the washer fluid cleaning system components or fluid lines, especially after a previous repair involving draining, opening, or replacing system components. The primary symptom is the inability to activate the camera wash function, often accompanied by a dashboard message indicating the issue.
Cause
The root cause of the inoperative BMW camera wash function is identified as unfavorable Basic Central Platform (BCP) software. This software prevents the autonomous cameras' washer fluid cleaning system from adequately purging air. Consequently, air can remain trapped in the system, hindering its proper operation.
Repair Procedure Summary
To resolve the inoperative BMW camera wash function, technicians must perform a specific programming and service function procedure. The steps are as follows:
- Determine Current I-level: The vehicle's current I-level must be identified using either the AIR system or the Key Reader/Aftersales Workplace (AWP) application.
- Perform Vehicle Test: A complete vehicle test using ISTA is required to confirm that no other related faults are stored in the system.
- Software Update:
- If the vehicle's I-level is between 23-07-500 and 24-07-500, the vehicle must be programmed to ISTA 4.48.1x to I-level 24-07-500 or higher.
- If the I-level is already above 24-07-500 or if the vehicle was recently programmed with ISTA 4.48.1x or a higher version, proceed to the next step.
- Perform Service Function: After the software update, or if the I-level is already current, the
Frequently Asked Questions
- Why is my BMW's camera wash function not working?
- Your BMW's camera wash function might not be working because air is trapped in the washer fluid system or due to unfavorable Basic Central Platform (BCP) software. This prevents the system from purging air effectively, leading to the "FRONT OR REAR AUTONOMOUS CAMERA WASH FUNCTION CANNOT BE STARTED" message.
- What is BMW SIB 66 04 24?
- BMW SIB 66 04 24 is a Service Information Bulletin issued by BMW to address an issue with the autonomous camera wash function not starting in certain 2023-2024 models. It provides diagnostic and repair procedures, primarily involving a software update and a specific service function.
- How is the "FRONT OR REAR AUTONOMOUS CAMERA WASH FUNCTION CANNOT BE STARTED" issue fixed?
- The issue is typically fixed by programming the vehicle to the latest I-level software, specifically ISTA 4.48.1x to I-level 24-07-500 or higher. Following the software update, a "Sensor washer system start-up" service function must be performed using ISTA to properly ventilate the camera wash system.
- What is the Basic Central Platform (BCP) software error 6138450200?
- The Basic Central Platform (BCP) software error, identified by repair code 6138450200, refers to an internal device fault within the BCP software. This specific error is linked to the inability of the autonomous camera wash system to purge air, causing the BMW camera wash function to not start.
Related Articles
2024-2025 BMW 530i Sunroof Water Drain Hose Leak
BMW has released a service action (NHTSA ID: 11029005) for 2024-2025 530i vehicles concerning the sunroof water drain hose. An improperly connected hose can lead to water entering the driver's footwell and soaking the carpet. Owners are advised to contact a BMW center for a free inspection and…
2024-2025 BMW Wiring Harness Return Bulletin C32-0126-0607
BMW Parts Bulletin C32-0126-0607 instructs dealers to inspect and return specific wiring harness part numbers. This bulletin, also known as TEC827, ensures that potentially affected components are removed from inventory for 2024-2025 BMW 530i, X3, and 740i models.
2024 BMW 5 Series Fuel Tank Evaporative Leak SIB 16 02 25
BMW's Service Information Bulletin SIB 16 02 25 addresses a manufacturing defect in the fuel tank of certain 2024 5 Series (G60) vehicles. This can lead to a "service engine soon" light or a fuel smell due to an evaporative leak. The repair involves replacing the fuel tank.
2024-2025 BMW 5/7 Series DME Faults: SIB 12 11 25
BMW Service Information Bulletin (SIB) 12 11 25 identifies a software issue in the Digital Motor Electronics (DME) of certain 2024-2025 BMW 5 Series (G60) and 7 Series (G70) vehicles. This can lead to various fault codes, including 034AA5 and 034AA8, related to mixture control and irregular…
2023-2024 BMW 5 Series Sedan Increased Door Closing Force
BMW has issued Service Information Bulletin SIB 51 03 25 to address instances where owners of 2023-2024 BMW 5 Series Sedan (G60) vehicles experience increased force or speed required to close their front and/or rear doors. This issue is caused by hinge misalignment and can be corrected by dealer…
Leave a comment
Comments are moderated and may take a moment to appear. Only your first name and the initial of your last name are shown publicly.
Comments
Be the first to comment.