Mercedes-Benz GLC-Class Service Bulletins

657 manufacturer communications on file.

• September 10, 2024•Document ID: 11007673

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI98.00-P-078106

  Date Added:

  September 11, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.

  Associated Products (57)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class+ 37 more
  Associated Documents

  • DownloadMC-11007673-0001.pdf↗
• September 9, 2024•Document ID: 11007790

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078304

  Date Added:

  September 14, 2024

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.

  Associated Products (109)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz S-Class+ 89 more
  Associated Documents

  • DownloadMC-11007790-0001.pdf↗
• September 9, 2024•Document ID: 11007728

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.00-P-075630

  Date Added:

  September 12, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LI’s before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?

  Associated Products (85)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class+ 65 more
  Associated Documents

  • DownloadMC-11007728-0001.pdf↗
• September 7, 2024•Document ID: 11007731

  Service Campaign
  FUEL/PROPULSION SYSTEM; ELECTRICAL SYSTEM

  Mfr Comm. #:

  2024080006

  Date Added:

  September 12, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  1. Connect XENTRY Diagnosis. 2. Update Fuel System Control Unit (FSCU10) software. To do this, select menu item "Quick test view . N118/3 – Control unit ‘Fuel pump’ (FSCU10) . Adaptations . Control unit update . Updating of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.

  Associated Products (12)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11007731-0001.pdf↗
• September 4, 2024•Document ID: 11007674

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; POWER TRAIN

  Mfr Comm. #:

  LI54.18-P-078334

  Date Added:

  September 11, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The cable duct of the high-voltage drive line wiring harness is unhooked from the holder and makes contact with the transmission crossbeam. This may cause noises (clattering/vibrating) at the underbody. Cause Due to insufficient holding ability of the catch tab at the underbody cable duct, the cable duct may become unhooked. Remedy Perform a visual check of the cable duct and the attachment point. Apply a high-temperature cable tie (see remedy and parts).

  Associated Products (3)

  2020 Mercedes-Benz GLC-Class2019 Mercedes-Benz GLC-Class2018 Mercedes-Benz GLC-Class
  Associated Documents

  • DownloadMC-11007674-0001.pdf↗
• August 30, 2024•Document ID: 11006710

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20240830

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.

  Associated Products (19)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz C-Class2021 Mercedes-Benz GLC-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11006710-0001.pdf↗
• August 23, 2024•Document ID: 11006712

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20240823

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY23-24 GLC, C-Class (254, 206 platform) vehicles, the door control unit software does not correspond with the latest series production configuration. The door control unit software will receive an OTA update for the SCN coding. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

  Associated Products (4)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class
  Associated Documents

  • DownloadMC-11006712-0001.pdf↗
• August 23, 2024•Document ID: 11006636

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI15.40-P-077947

  Date Added:

  August 28, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Combustion engine can no longer be started, only electric driving possible Cause High-voltage belt-driven starter-alternator has a failure Remedy Requirement: Prior to the implementation of the test work, it must be ensured that the person carrying out this work has successfully completed the qualification "T1716F Diagnosis at high voltage level 4" and the vehicle-specific training. Note: In order to check whether the high-voltage belt-driven starter-alternator has a failure, please carry out the test below. If the fault "P0E2F00 The electrical fuse B for the high voltage has a malfunction" is stored in the N82/10 BMS control unit, the HV protocol must be checked to see whether the fuse for the auxiliary consumers has a failure. In this case, the high-voltage battery must be replaced after the short circuit has been eliminated. (See attachment) The faulty component high-voltage belt-driven starter-alternator must always be sent back via the existing return delivery process for analysis. Check: Please disconnect the high-voltage plug at the high-voltage belt-driven starter-alternator and connect test adapter 000 589 94 63 00. Measure resistance HV+ to HV-. If the final measurement result is between 0–1 ohm, the high-voltage belt-driven starter-alternator with the short circuit must be replaced. If either one of or both the fault codes P0C0B16 and P0C0B17 are saved in the high-voltage belt-driven starter-alternator control unit G2/3, please replace the high-voltage belt-driven starter-alternator, since no short circuit can be measured here and this therefore concerns a hardware failure. Please check the serial number on the silver adhesive label below the SW number on the front of the high-voltage belt-driven starter-alternator. Example: 2314300044 (the first 10 digits, see attachment) Important note: If the number is small or greater than 2329100027, a TIPS case must be created. In this instance, please attach the following documents to the TIPS case: • Quick test • High-voltage event log • Picture of the silver adhesive label on the front of the high-voltage belt-driven starter-alternator (serial number) • Attach the measurement results with pictures approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

  Associated Products (3)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11006636-0001.pdf↗
• August 23, 2024•Document ID: 11006635

  Other
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  CL-2024030012

  Date Added:

  August 28, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  An authorized Mercedes-Benz dealer will update the control unit software for the electronic ignition lock in your vehicle, free of charge. Your vehicle must be brought to a dealership to complete the update.

  Associated Products (3)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11006635-0001.pdf↗
• August 14, 2024•Document ID: 11006700

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-077242

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.

  Associated Products (36)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class+ 16 more
  Associated Documents

  • DownloadMC-11006700-0001.pdf↗
• August 10, 2024•Document ID: 11006658

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2022080005

  Date Added:

  August 29, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (“MY”) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.

  Associated Products (74)

  2018 Mercedes-Benz AMG GT2018 Mercedes-Benz C-Class2018 Mercedes-Benz CLS-Class2018 Mercedes-Benz E-Class2018 Mercedes-Benz G-Class2018 Mercedes-Benz GLC-Class2018 Mercedes-Benz GLE-Class2018 Mercedes-Benz GLS-Class2018 Mercedes-Benz S-Class2018 Mercedes-Benz SL-Class2017 Mercedes-Benz AMG GT2017 Mercedes-Benz C-Class2017 Mercedes-Benz CLS-Class2017 Mercedes-Benz E-Class2017 Mercedes-Benz G-Class2017 Mercedes-Benz GLC-Class2017 Mercedes-Benz GL-Class2017 Mercedes-Benz GLE-Class2017 Mercedes-Benz GLS-Class2017 Mercedes-Benz S-Class+ 54 more
  Associated Documents

  • DownloadMC-11006658-0001.pdf↗
• August 9, 2024•Document ID: 11031806

  Other
  ENGINE

  Mfr Comm. #:

  CL-Intake Line Assembly

  Date Added:

  April 30, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (“MBUSA”) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (‘MIL’). A faulty partial-load ventilation valve might also increase exhaust gas emission. Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

  Associated Products (15)

  2019 Mercedes-Benz E-Class2019 Mercedes-Benz GLC-Class2019 Mercedes-Benz SLC-Class2018 Mercedes-Benz C-Class2018 Mercedes-Benz E-Class2018 Mercedes-Benz GLC-Class2018 Mercedes-Benz SLC-Class2017 Mercedes-Benz C-Class2017 Mercedes-Benz E-Class2017 Mercedes-Benz GLC-Class2017 Mercedes-Benz SLC-Class2016 Mercedes-Benz C-Class2016 Mercedes-Benz GLC-Class2016 Mercedes-Benz SLK-Class2015 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11031806-0001.pdf↗
• August 9, 2024•Document ID: 11008064

  Other
  ELECTRICAL SYSTEM; ENGINE

  Mfr Comm. #:

  CL - 2022080005

  Date Added:

  September 26, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.

  Associated Products (73)

  2018 Mercedes-Benz AMG GT2018 Mercedes-Benz C-Class2018 Mercedes-Benz CLS-Class2018 Mercedes-Benz E-Class2018 Mercedes-Benz G-Class2018 Mercedes-Benz GLC-Class2018 Mercedes-Benz GLE-Class2018 Mercedes-Benz GLS-Class2018 Mercedes-Benz S-Class2018 Mercedes-Benz SL-Class2017 Mercedes-Benz AMG GT2017 Mercedes-Benz C-Class2017 Mercedes-Benz CLS-Class2017 Mercedes-Benz E-Class2017 Mercedes-Benz G-Class2017 Mercedes-Benz GLC-Class2017 Mercedes-Benz GL-Class2017 Mercedes-Benz GLE-Class2017 Mercedes-Benz GLS-Class2017 Mercedes-Benz S-Class+ 53 more
  Associated Documents

  • DownloadMC-11008064-0001.pdf↗
• August 8, 2024•Document ID: 11006675

  Service Campaign
  ELECTRICAL SYSTEM; UNKNOWN OR OTHER

  Mfr Comm. #:

  NCU - 2024070020

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Update Digital Operator's Manual. 1. Connect XENTRY Diagnosis. 2. Update Digital Operator's Manual. To do this, select menu item "Quick test view . A26/17 - MBUX multimedia system (head unit) . Adaptations . Control unit update . Update control unit software". Then follow the user guidance in XENTRY Diagnosis. The Digital Operator's Manuals are downloaded automatically via Retail Data Storage to XENTRY Diagnosis to match the affected vehicle. 3. Disconnect XENTRY Diagnosis. 4. Check whether the Operator's Manual in the vehicle document wallet, as well as the supplements and ACCORDION-FOLD DOCUMENT are present and whether the version is correct. The missing or incorrect Operator's Manual, as well as the supplements and ACCORDION-FOLD DOCUMENT must be replaced or enclosed as an aftermarket measure. The Operator's Manual, as well as the supplements and ACCORDION-FOLD DOCUMENT must be determined according to the equipment variant for the vehicle identification number via the parts process in the XENTRY Portal.

  Associated Products (2)

  2024 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLC-Class
  Associated Documents

  • DownloadMC-11006675-0001.pdf↗
• August 8, 2024•Document ID: 11006541

  Service Bulletin/Repair Instructions
  ENGINE; POWER TRAIN

  Mfr Comm. #:

  LI01.00-P-078172

  Date Added:

  August 21, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Dull thumping noise or ticking noise under the vehicle in the area of the engine/two-mass flywheel/transmission. Is significantly perceptible at the front right wheel well and can also be faintly heard in the vehicle interior. Cause The ticking noise occurs in idle operation in drive program C & S at 780 rpm when the state of charge of the battery is over 65% and the load requirement at the belt-driven starter alternator is simultaneously over 25 Nm. The load requirement can occur due to a number of auxiliary consumers (e.g. air conditioning system, steering wheel or seat heating, etc.). Remedy Switch off the auxiliary consumers and check whether the noise goes away. Remedial action by means of software update under development. Do not replace any parts Create TIPS case and send to HQ together with the following documents: • Videos of the problem from the exterior and in the vehicle interior • Control unit log, engine N3/10 (ME) • Control unit log, drivetrain N127 (PTCU) • Control unit log, DC/DC converter N83/12 (DDW)

  Associated Products (5)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11006541-0001.pdf↗
• August 6, 2024•Document ID: 11006699

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-078155

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Complaint Radio reception interference and the following DTCs are displayed in the A26/17 - MBUX multimedia system control unit as "active and stored": • B19B313 - Antenna 1 open load • B19B413 - Antenna 2 open load • B19B513 - Antenna 3 open load • B19B613 - Antenna 4 open load Cause Antenna amplifier Remedy Replace the antenna amplifier.

  Associated Products (14)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11006699-0001.pdf↗
• August 5, 2024•Document ID: 11006695

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-078156

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: • E504.3 (A 297 904 97 00) • E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed. Note: A remedy is not yet available. Replacing the hardware does not resolve the symptom. Do not replace the MBUX for this concern. The information will be updated accordingly as soon as a remedy is available.

  Associated Products (10)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLE-Class
  Associated Documents

  • DownloadMC-11006695-0001.pdf↗
• July 26, 2024•Document ID: 11005286

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI20.10-P-076206

  Date Added:

  July 27, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customer states that the CEL is lit in the instrument cluster Cause Debris in the coolant systemRemedy Please refer to the specific repair instructions for the vehicle you are working on in the attachments section of this LI. Before beginning work on the vehicle open a TIPS case and request the tool you will need. In your request include a contact name, phone number, and shipping address for the tool to be sent. Before the tool arrives: • Remove and replace the coolant expansion tank (reservoir) and the main radiator. • Without removing the components: flush the heater core and changeover valve (located in the right front wheel arch) in the opposite direction of flow until no debris remains. Once the tool arrives, proceed with flushing the vehicle per the instructions attached in this LI. A picture of the filter after each flush must be taken. If after the prescribed number of flushing attempts debris is still being collected in the filter, upload all the pictures to the TIPS case and wait for next steps. A scale of not-acceptable to acceptable debris level in the filter is in the attachments for you to make an assessment as well.

  Associated Products (14)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2020 Mercedes-Benz CLA-Class
  Associated Documents

  • DownloadMC-11005286-0001.pdf↗
• July 23, 2024•Document ID: 11005294

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078069

  Date Added:

  July 27, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11005294-0001.pdf↗
• July 22, 2024•Document ID: 11005336

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.10-P-078070

  Date Added:

  July 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Digital light pop-up messages (warnings, notes, spotlight and dyn. low beam) appear in the instrument cluster (picture in attachment), even though the same digital light settings are stored in all MBUX profiles Note: The pop-up messages are intended to indicate different settings when changing MBUX profiles Cause - ECU software error Remedy - Reset MBUX to manufacturer default settings. Software update expected to be available YoM24/2 (Year of Modification - Code can be found in VeDoc): - A26/17 - MBUX multimedia system (head unit) -This document will be updated when the software is available.

  Associated Products (14)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11005336-0001.pdf↗