BMW M6 Service Bulletins
418 manufacturer communications on file.
- November 1, 2013•Document ID: 10150171Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT
- Mfr Comm. #:
- 511613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryBang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly
Associated Products (55)Associated Documents - November 1, 2013•Document ID: 10150166Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model.
Associated Products (52)Associated Documents - November 1, 2013•Document ID: 10150161Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- 121713
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
Associated Products (83)Associated Documents - October 1, 2013•Document ID: 10150266Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 651113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryInstallation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
Associated Products (57)Associated Documents - October 1, 2013•Document ID: 10150263Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 640113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"IHKA Operating Panel Buttons Are Peeling. INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the ""Repair kit for button caps"" when performing this repair. Replace ALL the buttons with those included in the kit. Note: Please do not use and claim the part number for the "Repair kit, radio and A/C panel." To ensure the button cap kit with the correct symbols and labels is installed, perform a part number lookup in ETK by VIN. Labor operation code 64 11 326 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 64 11 769 instead."
Associated Products (57)Associated Documents - October 1, 2013•Document ID: 10150257Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (71)Associated Documents - October 1, 2013•Document ID: 10150256Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130413
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.
Associated Products (77)Associated Documents - September 1, 2013•Document ID: 10152347Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130413
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013
Associated Products (77)Associated Documents - September 1, 2013•Document ID: 10152344Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110513
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryTurbocharger Coolant Return Pipe Leaking. A Check Control message for low coolant level is displayed. There are traces of coolant leaking in the engine compartment at the turbochargers. The auxiliary coolant pump for the turbochargers does not run during an MSA shutdown. Frequent MSA starts and stops could result in excessive temperatures in the cooling circuit of the turbochargers.
Associated Products (4)Associated Documents - September 1, 2013•Document ID: 10152343Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110413
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"The customer complains that the ""low engine oil"" message is displayed too frequently. CAUSE The cause is related to, but not limited to, one or more of the following components and systems shown below: * Turbocharger * Crankcase ventilation * Engine gasket leaks * Internal engine tolerances and sealing * Improper filling or topping up Use the troubleshooting procedure below to help identify the cause."
Associated Products (26)Associated Documents - September 1, 2013•Document ID: 10053584Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE
- Mfr Comm. #:
- SB-11-05-13
- Date Added:
- November 8, 2013
- Manufacturer:
- BMW
SummaryBMW: CHECK COOLANT MESSAGE ILLUMINATED. ACCORDING TO THE DEALER THERE ARE TRACES OF COOLANT LEAKING INTO THE ENGINE COMPARTMENT AT THE TURBOCHARGERS. VEHICLES WITH S63T ENGINE. *KB
Associated Products (2)Associated Documents - August 1, 2013•Document ID: 10150235Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 651913
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryHU-H: SDARS Radio Stations Cannot Be Stored in PRESET Menu. The SIRIUS/XM satellite radio (SDARS) stations cannot be stored in the PRESET menu. * No fault code related to this issue is stored in the HU-H. * AM/FM radio stations are not affected; they can be stored correctly. Software error in the SDARS control unit integrated in the Headunit-High (HU-H)
Associated Products (59)Associated Documents - August 1, 2013•Document ID: 10150233Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary? Bang & Olufsen Sound System: Loudspeaker Illumination. One or more of the following situations may occur concerning the illumination of the Bang & Olufsen sound system loudspeakers: * Illumination is insufficient (not bright enough) * Illumination is not available on all loudspeakers * Brightness cannot be adjusted Loudspeaker illumination settings are dependent on the model: * Different brightness characteristics * Not all loudspeakers are illuminated INFORMATION Explain to the customer that loudspeaker illumination can vary from model to model. For an overview of the illuminated loudspeakers, refer to the attachment. IMPORTANT: The current version of the Owner's Manual for 5 Series vehicles is incorrect. On 5 Series vehicles (F07 and F10), only the main loudspeaker (moving part) in the dashboard and the two loudspeakers in the mirror triangles in the front doors are illuminated. The Owner's Manuals for 5 Series vehicles will be corrected with start of production of the MY2014 vehicles (July 2013).
Associated Products (40)Associated Documents - August 1, 2013•Document ID: 10150231Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 630513
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"FRM3 Will Not Communicate with ISTA. When diagnosing the vehicle with ISTA, the FRM3 (Footwell Module) is shown as not responding in the vehicle test. The customer may report one or more of the following malfunctions: 1. Light operation * CCM (Check Control Message) ""Display failure"" * Lighting INOP * Turn signal lights INOP * Break lights INOP * License plate light INOP * Courtesy lights INOP * Instrument cluster w/o light 2. Windows * One or both front windows INOP 3. LIN components https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15625.1.B630513... 8/29/2013 Page 2 of 2 * CCM ""no blind spot detection"" if equipped * Power mirrors INOP * Seat adjustment INOP 4. Hardware inputs * Door locks INOP * Gear shifts automatically to P * Gear shift lever cannot be moved out of P 5. Electrical steering column adjustment * ELSV (Electric Steering Column Adjustment) INOP CAUSE Various causes include the following: * Blown fuse * Faulty wiring * Faulty component"
Associated Products (61)Associated Documents - August 1, 2013•Document ID: 10150222Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummarySqueaking Noise from Front Axle Brakes when Driving Over Bumps.
Associated Products (4)Associated Documents - August 1, 2013•Document ID: 10150219Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310112
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (71)Associated Documents - June 1, 2013•Document ID: 10150076Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- 620613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (70)Associated Documents - June 1, 2013•Document ID: 10150075Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 611313
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Service Action: Program Control Units (CAS). The Car Access System (CAS) was incorrectly coded with ISTA/P 2.49.2 or earlier, causing the anti-theft alarm system panic button on the remote control to stop functioning. AFFECTED VEHICLES This Service Action involves F12 vehicles which were produced from August 2010 to June 2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 648. If code number 648 has been punched out, the campaign has already been performed. If code number 648 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A Campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this Campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (8)Associated Documents - June 1, 2013•Document ID: 10150073Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; VISIBILITY
- Mfr Comm. #:
- 511113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryRattling Noise from Windshield Defroster Vents. Rattling noises can be heard from the instrument panel where the defroster vents are located.
Associated Products (8)Associated Documents - June 1, 2013•Document ID: 10150072Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 510813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryWater Leaking into Trunk. Water leaks into the trunk on the left or right side. CAUSE The trunk lid hinge bracket fastener is not sealed to the body properly.
Associated Products (8)Associated Documents