BMW 535d Service Bulletins
362 manufacturer communications on file.
- April 1, 2014•Document ID: 10148258Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (80)Associated Documents - April 1, 2014•Document ID: 10148257Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL
- Mfr Comm. #:
- 130114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of ""Incorrect diesel exhaust fluid"" may be displayed with ""no start scenario countdown"" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software"
Associated Products (20)Associated Documents - March 1, 2014•Document ID: 10148010Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Associated Products (211)Associated Documents - March 1, 2014•Document ID: 10147923Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 612213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"""Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
Associated Products (58)Associated Documents - March 1, 2014•Document ID: 10147921Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- 360114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFitting Winter Tires Properly to Vehicles with Ceramic Brakes. Wheel studs may loosen after wheels for the rear axle are incorrectly fitted to the front axle on vehicles equipped with option 2NK (ceramic brakes). Incorrect installation of rear axle winter tires (wheel style 409M) onto the front axle in conjunction with ceramic brakes
Associated Products (33)Associated Documents - March 1, 2014•Document ID: 10147918Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION There is an error in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. The vehicle may also exhibit rough running at idle and while driving. F07 and F10: P/N 13 64 7 639 994 is for all vehicles produced from 7/2014 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2014 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 F06, F12 and F13: P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 Until further notice, it is good practice to verify that the injector part number being removed from the engine matches the new injector part number. Always review the vehicle history to identify if the injectors have already been replaced. When the ETK data is corrected, a notification will be distributed. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16028.3.B130413... 4/24/2014
Associated Products (35)Associated Documents - February 1, 2014•Document ID: 10147985Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMy BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
Associated Products (66)Associated Documents - February 1, 2014•Document ID: 10147984Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 840613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
Associated Products (94)Associated Documents - February 1, 2014•Document ID: 10147982Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 652313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
Associated Products (98)Associated Documents - February 1, 2014•Document ID: 10147981Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 650414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Airbag Warning Light: ACSM FC 930A60 Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
Associated Products (88)Associated Documents - February 1, 2014•Document ID: 10147976Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThe Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (88)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents - January 1, 2014•Document ID: 10147952Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.
Associated Products (90)Associated Documents - January 1, 2014•Document ID: 10147946Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. CAUSE Software error in TMS 3 (Headlight driver module AHL xenon light)"
Associated Products (38)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents - January 1, 2014•Document ID: 10147706Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
Associated Products (54)Associated Documents - November 1, 2013•Document ID: 10150185Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 651813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryTouchpad Integrated in the iDrive Controller Is Intermittently Inoperative. Intermittently the Touchpad integrated in the iDrive controller is inoperative. * No entries can be made using the Touchpad * Fault code is stored in the touch-box control unit Software error in the touch-box control unit (TBX)
Associated Products (38)Associated Documents - November 1, 2013•Document ID: 10150183Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 630713
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryDaytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
Associated Products (41)Associated Documents - November 1, 2013•Document ID: 10150171Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT
- Mfr Comm. #:
- 511613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryBang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly
Associated Products (55)Associated Documents