Nissan Titan Service Bulletins
691 manufacturer communications on file.
- February 8, 2018•Document ID: 10130494Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- NTB17-109a
- Date Added:
- March 26, 2018
- Manufacturer:
- NISSAN
Summary2016 - 2018 TITAN AND TITAN XD; CLIMATE CONTROLLED HEATED AND COOLED SEATS POOR OR NO OPERATION This bulletin applies only to vehicles equipped with climate controlled seats. This bulletin has been amended. The APPLIED VEHICLES section and pages 17 and 18 have changed. No other changes have been made. Please discard previous versions of this bulletin.
Associated Products (3)Associated Documents - February 1, 2018•Document ID: 10130491Service Bulletin/Repair InstructionsFUEL SYSTEM, DIESEL
- Mfr Comm. #:
- NTB16-056b
- Date Added:
- March 26, 2018
- Manufacturer:
- NISSAN
Summary2016-2018 TITAN XD; EXHAUST SMELL INSIDE VEHICLE WHEN HVAC IS ON FRESH AIR This bulletin applies only to vehicles equipped with a Cummins Diesel engine. This bulletin has been amended to update Applied Vehicles, remove the installation of a micro filter and to add a reprogramming procedure. No other changes have been made. Please discard previous versions of this bulletin.
Associated Products (3)Associated Documents - January 30, 2018•Document ID: 10128642Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB17-060a
- Date Added:
- February 12, 2018
- Manufacturer:
- NISSAN
Summary2016-2017 TITAN XD; DTC P207F AND DEF SYSTEM ERROR IS DISPLAYED ON THE VEHICLE INFORMATION DISPLAY This bulletin applies to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. The Title and all sections on page 1 have been updated. Table A has also been updated. Please discard previous versions of this bulletin.
Associated Products (2)Associated Documents - January 26, 2018•Document ID: 10130690Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; FUEL SYSTEM, DIESEL
- Mfr Comm. #:
- NTB18-005
- Date Added:
- April 2, 2018
- Manufacturer:
- NISSAN
Summary2016-2017 TITAN XD WITH CUMMINS 5.0L; IDLE FLUCTUATION DURING LOW TEMPERATURE WARM-UP This bulletin applies to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM An applied vehicle?s idle fluctuates after starting when: - The coolant temperature is between 68°F (20°C) and 104°F (40°C) and - The vehicle is not moving (0 MPH). NOTE: This incident may continue until the coolant temperature reaches 104°F (40°C). ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
Associated Products (2)Associated Documents - January 22, 2018•Document ID: 10130688Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- NTB18-003
- Date Added:
- April 2, 2018
- Manufacturer:
- NISSAN
Summary2004-2015 TITAN; SQUEAK OR TICK NOISE FROM LEAF SPRINGS IF YOU CONFIRM: A squeak or tick noise coming from the rear suspension leaf springs when driving. NOTE: - Noise is more pronounced when driving over rough roads below 30 mph. - Chassis ears may be helpful to isolate this noise. - If the source of the squeak or tick noise is NOT either the left or right side leaf spring, this bulletin does not apply. Refer to ASIST for further diagnostic and repair information. ACTION: Clean the rear leaf spring tip inserts.
Associated Products (12)Associated Documents - January 8, 2018•Document ID: 10130683Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:DOORS:LATCH
- Mfr Comm. #:
- NTB17-056a
- Date Added:
- April 2, 2018
- Manufacturer:
- NISSAN
Summary2016-2018 TITAN AND TITAN XD; DOOR WILL NOT OPEN OR DOOR WILL NOT LATCH This bulletin has been amended. The APPLIED VEHICLES have been updated and the SERVICE PROCEDURE now includes the addition of foam to the outside handle bracket. Please discard previous versions of this bulletin.
Associated Products (3)Associated Documents - January 5, 2018•Document ID: 10129119Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- REVISION 3_P7318
- Date Added:
- February 21, 2018
- Manufacturer:
- NISSAN
SummaryAir Bag Control Unit Reprogram Voluntary Service Campaign UPDATE January 5, 2018 The announcement from October 6, 2017 has been revised: - Dealers may now use revised TSB NTB17-070 to resume repair of 2004-2006 model year vehicles. Please discard previous versions of this bulletin
Associated Products (31)2014 Nissan Frontier2014 Nissan Titan2014 Nissan Xterra2013 Nissan Frontier2013 Nissan Titan2013 Nissan Xterra2012 Nissan Frontier2012 Nissan Titan2012 Nissan Xterra2011 Nissan Frontier2011 Nissan Titan2011 Nissan Xterra2010 Nissan Frontier2010 Nissan Titan2010 Nissan Xterra2009 Nissan Frontier2009 Nissan Titan2009 Nissan Xterra2008 Nissan Frontier2008 Nissan Titan+ 11 moreAssociated Documents - January 4, 2018•Document ID: 10130684Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; AIR BAGS
- Mfr Comm. #:
- NTB17-070a
- Date Added:
- April 2, 2018
- Manufacturer:
- NISSAN
SummaryVOLUNTARY SERVICE CAMPAIGN 2004-2011 TITAN, AND 2005-2011 FRONTIER AND XTERRA; AIR BAG DIAGNOSIS SENSOR UNIT This bulletin has been amended. The reprogramming procedure has been revised. No other changes have been made. Discard all previous versions of this bulletin.
Associated Products (22)2011 Nissan Frontier2011 Nissan Titan2011 Nissan Xterra2010 Nissan Frontier2010 Nissan Titan2010 Nissan Xterra2009 Nissan Frontier2009 Nissan Titan2009 Nissan Xterra2008 Nissan Frontier2008 Nissan Titan2008 Nissan Xterra2007 Nissan Frontier2007 Nissan Titan2007 Nissan Xterra2006 Nissan Frontier2006 Nissan Titan2006 Nissan Xterra2005 Nissan Frontier2005 Nissan Titan+ 2 moreAssociated Documents - January 4, 2018•Document ID: 10128640Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- NTB15-049n
- Date Added:
- February 12, 2018
- Manufacturer:
- NISSAN
SummaryTELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.
Associated Products (22)2018 Nissan Altima2018 Nissan Armada2018 Nissan GT-R2018 Nissan Maxima2018 Nissan Murano2018 Nissan Pathfinder2018 Nissan Rogue2018 Nissan Sentra2018 Nissan Titan2017 Nissan Altima2017 Nissan GT-R2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Rogue2017 Nissan Sentra2017 Nissan Titan2016 Nissan Altima2016 Nissan Maxima2016 Nissan Rogue+ 2 moreAssociated Documents - December 19, 2017•Document ID: 10127459Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- PC604 2016-17
- Date Added:
- January 29, 2018
- Manufacturer:
- NISSAN
SummaryTransmission Control Module Reprogram ***** Quality Action Summary ***** Nissan is conducting a dealer inventory quality action to reprogram and, if necessary calibrate, the Transmission Control Module (TCM) on specific MY2016-17 Titan XD (A61) vehicles identified in SERVICE COMM and National Service History ? Open Campaigns. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. The software update will prevent one or more of the following concerns: - Transmission shift shock when accelerating enough to create a 7 3 downshift - Engine RPM fluctuation while driving at a steady speed - Lack of power under light acceleration at low speeds (may be described as hesitation; feeling like the transmission is in too high of a gear) ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by using Service Comm or National Service History ? Open Campaign I.D. PC604. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to reprogram the TCM and, if applicable, the ECM. - If reprogramming issues arise, use CONSULT III Software version 73.10 - Use the following claims information for vehicles identified in Service Comm or DBS National Service History ? Open Campaigns ID PC604 3. Dealers are requested to remedy any affected vehicle in dealer new inventory to ensure customer satisfaction. Thank you for your prompt attention to this matter. NISSAN NORTH AMERICA, INC. Aftersales DIVISION
Associated Products (2)Associated Documents - December 18, 2017•Document ID: 10127456Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- NTB17-127
- Date Added:
- January 29, 2018
- Manufacturer:
- NISSAN
SummaryNISSAN; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE SERVICE INFORMATION When the initialization procedure being performed with a new or existing Intelligent Key to an applied vehicle is interrupted (the procedure stops or will not continue), the BCM may be left in learn mode and will not function until it returns to normal mode. Under this condition, the BCM and Intelligent Key(s) will not function normally. If this condition occurs, the BCM must be returned to normal mode and the initialization procedure started over. To get back to the beginning of the Initialization procedure, use one of the following procedures: - Successfully perform the initialization procedure using one of the original Intelligent Keys twice consecutively. - Each successful initialization will follow with two (2) quick tones. OR - When the initialization procedure cannot be successfully performed twice (more than two quick tones), perform the initialization procedure five (5) times using the inoperative ?failed? Intelligent Key. - Initialization does not need to be successful when performed five times. When returning to normal operating mode, the initialization procedure for all Intelligent Keys may be started again.
Associated Products (5)Associated Documents - December 1, 2017•Document ID: 10127452Service Bulletin/Repair InstructionsFUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- NTB17-122
- Date Added:
- January 29, 2018
- Manufacturer:
- NISSAN
Summary2016 ? 2017 TITAN XD DIESEL; BLOCK HEATER INOPERATIVE This bulletin applies to vehicles equipped with a Cummins (5.0L V8) Diesel engine only. IF YOU CONFIRM The coolant heater (block heater) needs to be replaced based on the Electronic Service Manual (ESM) inspection, and The vehicle is currently equipped with a coolant heater (with attached cord) located in the front engine cover. NOTE: - This bulletin does not apply if the vehicle is equipped with a coolant heater located in the water inlet at the lower radiator hose. - Refer to the ESM, section CO ? Engine Cooling System, for coolant heater operation and inspection information. ACTION 1. Use the Service Procedure in this bulletin to install a new coolant heater, locating it in the water inlet at the lower radiator hose. 2. Cut the cord to the original coolant heater.
Associated Products (2)Associated Documents - November 27, 2017•Document ID: 10127474Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- NTB17-118
- Date Added:
- January 29, 2018
- Manufacturer:
- NISSAN
SummaryNISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.
Associated Products (12)Associated Documents - November 16, 2017•Document ID: 10127472Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- NTB17-116
- Date Added:
- January 29, 2018
- Manufacturer:
- NISSAN
Summary2016-2017 TITAN AND TITAN XD; EXCESSIVE VENT TEMPERATURE DIFFERENCE IN DUAL CLIMATE CONTROL MODE WITH THE SAME TEMPERATURE SETTING This bulletin applies to vehicles with dual climate control air conditioning. IF YOU CONFIRM With the HVAC system of an applied vehicle set in dual climate control mode and both driver and passenger sides are set at the same temperature: A. Temperature set for cool air: The outlet temperature of the driver side vents are warmer by 10°F or more than the passenger side vent temperatures OR B. Temperature set for warm air: The outlet temperature of the passenger side vents are cooler by 10°F or more than the driver side vent temperatures. ACTION 1. If A above is occurring: Replace only the driver side air mix door motor (see Parts Information). - Refer to the Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning Control System, for driver air mix door motor removal and installation. 2. If B above is occurring: Replace only the passenger side air mix door motor (see Parts Information). - Refer to the Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning Control System, for passenger air mix door motor removal and installation.
Associated Products (2)Associated Documents - November 15, 2017•Document ID: 10126441Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- NTB17-016e
- Date Added:
- December 22, 2017
- Manufacturer:
- NISSAN
SummaryARMADA, TITAN AND TITAN XD; SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies to vehicles with a gasoline V8 engine only. This bulletin has been amended to add Armada to the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
Associated Products (3)Associated Documents - November 14, 2017•Document ID: 10126254Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- NTB15-049m
- Date Added:
- December 22, 2017
- Manufacturer:
- NISSAN
SummaryTELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.
Associated Products (22)2018 Nissan Altima2018 Nissan Armada2018 Nissan GT-R2018 Nissan Maxima2018 Nissan Murano2018 Nissan Pathfinder2018 Nissan Rogue2018 Nissan Sentra2018 Nissan Titan2017 Nissan Altima2017 Nissan GT-R2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Rogue2017 Nissan Sentra2017 Nissan Titan2016 Nissan Altima2016 Nissan Maxima2016 Nissan Rogue+ 2 moreAssociated Documents - November 6, 2017•Document ID: 10126440Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- NTB17-016d
- Date Added:
- December 22, 2017
- Manufacturer:
- NISSAN
Summary2016 - 2017 TITAN AND TITAN XD; SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies to vehicles with a gasoline V8 engine only. This bulletin has been changed throughout. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.
Associated Products (2)Associated Documents - November 1, 2017•Document ID: 10126437Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY
- Mfr Comm. #:
- PC594 2016-17
- Date Added:
- December 22, 2017
- Manufacturer:
- NISSAN
SummaryFuel Tank Breather Tube Dealer Inventory ***** Detailed Information ***** Nissan is conducting a dealer inventory quality action to inspect the routing of the fuel tank breather tube on approximately 4,288 specific MY2016-17 Titan XD (A61D) vehicles. During vehicle assembly, certain plant operator technicians may not have removed the temporary fuel tank breather tube cap, and may not have correctly affixed the tube to the bed rail. No parts are required for this inspection. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History - Open Campaign I.D. PC594 - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). i. Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect the vehicle. - If the fuel tank breather tube is routed correctly, file a claim for the inspection. - If the fuel tank breather tube is not routed correctly, provide the requested information in an email to [email protected] and await further instruction. Instructions and claims information will be provided within 48 hours. 3. Dealers are requested to inspect any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.
Associated Products (2)Associated Documents - November 1, 2017•Document ID: 10126256Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- NTB17-031a
- Date Added:
- December 22, 2017
- Manufacturer:
- NISSAN
Summary2016 - 2017 TITAN XD; COOLANT HEATER (ENGINE BLOCK HEATER) INSTALLATION This bulletin applies to vehicles with a Cummins (5.0L V8) Diesel engine only. This bulletin has been amended. Substantial changes have been made throughout the body of the bulletin. Please discard all previous versions of this bulletin.
Associated Products (2)Associated Documents - October 17, 2017•Document ID: 10123356Service Bulletin/Repair InstructionsSUSPENSION; STRUCTURE:BODY; WHEELS
- Mfr Comm. #:
- NTB17-110
- Date Added:
- November 14, 2017
- Manufacturer:
- NISSAN
Summary2004 - 2015 TITAN; VIBRATION AT 40 ? 50 MPH IF YOU CONFIRM A low frequency vibration at 40 ? 50 MPH AND The vehicle is equipped with the correct tires as shown on the TIRE AND LOADING INFORMATION LABEL on the driver side body side outer panel (B-pillar), (see Figure A). AND All 4 tires have been verified to be within specification for RH1 uniformity at or below 118 N (12 kg, 26.5 lbs.) as described in NTB11-062. ACTION Replace the 2 rearmost cab body mounts, nuts, and bolts with the new ones listed in the PARTS INFORMATION section of this bulletin.
Associated Products (11)Associated Documents