GMC Yukon Complaints

871 consumer complaints on file.

#11754742August 4, 2026
ENGINE
The contact owns a 2026 GMC Yukon. The contact stated that while driving 55 MPH and depressing the accelerator pedal, the vehicle failed to respond as intended. The contact pulled over to the side of the road, turned off and restarted the vehicle; however, the failure persisted. A dealer was contacted. The vehicle was towed to the dealer to be diagnosed, and the contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that there was a wait for the replacement engine. The approximate failure mileage was 3,788.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11754669August 4, 2026
STEERING, ELECTRICAL SYSTEM
The progressive failure of the factory steering wheel adhesive on my 2025 GMC Yukon creates an immediate, active safety hazard during vehicle operation. The material failure and sticky glue are localized directly around the integrated heating element of the steering wheel. This failure severely impacts driving maneuvers as well as a potential electrical fire hazard. The liquefied glue residue is incredibly sticky and continually transfers to the driver’s hands, resulting in a compromised, slippery grip on the steering wheel. During active driving maneuvers, such as hand-over-hand turning, navigating sharp curves, the loose edges of the peeling leather and separating trim physically catch on the driver's palms. This restricts smooth wheel rotation, disrupts natural hand movement, and threatens a sudden, temporary loss of steering control. This manufacturing defect introduces severe driver distraction and physical interference with critical steering components while driving, compounded by a potential thermal or electrical defect in the steering wheel heating assembly.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11754040July 31, 2026
POWER TRAIN, ELECTRICAL SYSTEM, ENGINE
GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11753973July 31, 2026
ENGINE
The contact owns a 2021 GMC Yukon. The contact stated that while driving approximately 50 MPH, the check engine warning light started blinking and the vehicle started shaking violently. The vehicle was pulled over to the side of the road and turned off. The vehicle was then towed to a dealer where it was diagnosed with a stuck lifter. The contact was informed that the lifters needed to be replaced. The vehicle was not repaired. The contact believed that the failure was associated with an undisclosed recall number. The manufacturer was notified of the failure. The failure mileage was approximately 100,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11753795July 30, 2026
BACK OVER PREVENTION
The contact owns a 2025 GMC Yukon. The contact stated that while the vehicle was shifted into reverse, the rear-view camera displayed a black screen. The image in the rear-view camera was not visible, specifically in areas where there were reflective lights. The dealer was contacted and assisted the contact with the brightness options on the rear-view camera and stated there was no failure with the camera. The camera was not repaired or replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 16.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11753505July 29, 2026
POWER TRAIN
The contact owns a 2021 GMC Yukon. The contact stated that while driving at undisclosed speeds, the transmission was shifting hard, with severe vibrations and shuddering. The vehicle was taken to the local mechanic, who confirmed the failure and advised the contact to take the vehicle to the local dealer. The vehicle was taken to the local dealer, and the failure was confirmed, but the vehicle was not repaired. The contact stated that the vehicle was previously serviced under NHTSA Campaign Number: 24V797000 (POWER TRAIN); however, the failure occurred. The manufacturer was notified of the failure, but no assistance was offered. The contact stated that the manufacturer had issued a special coverage associated with the failure but offered no assistance. There was no fault code retrieved associated with the previous software update that was performed under the recall campaign. The failure mileage was 78,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11753121July 27, 2026
ENGINE AND ENGINE COOLING, TRACTION CONTROL SYSTEM
The contact owns a 2021 GMC Yukon. The contact stated that while driving at an undisclosed speed, there was a misfire coming from the vehicle, the vehicle was shaking and vibrating abnormally before the vehicle went into LIMP Mode. The traction control light and other unknown warning lights were illuminated on the instrument panel. The vehicle was taken to a dealer to be diagnosed. The vehicle was diagnosed with a lifter failure inside the engine. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 86,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11752786July 25, 2026
ENGINE
Knocking sound and flashing engine light came on. When brought to dealership it was determined that lower bearing failure took place requiring full engine replacement. '
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11752500July 23, 2026
STEERING
The power steering went out. The dealership said it's the rack and pinion. This part is not available anywhere in the United States. I have been waiting over 3 weeks. I feel the part is unavailable as there is an issue with the rack and pinion and others who have the same vehicle ran into the same problem.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11752303July 23, 2026
ENGINE
2023 Yukon with 6.2; was "tested" at a local dealership in November 2025. Engine passed. Was given oil change with new oil/oil cap. In June of 2026, engine seized despite passing test in November & running the new oil since then.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11751947July 21, 2026
UNKNOWN OR OTHER
My 2023 GMC Yukon has had a strong mildew/musty odor coming from the HVAC system since the vehicle was new. The odor is most noticeable every time the vehicle is started after it has been sitting for several hours or overnight. After the system runs for a short time, the odor dissipates. This concern has been reported to my GMC dealer on multiple occasions. Previous repair attempts have not permanently corrected the problem, and the odor continues to worsen. The smell is now strong enough that it is embarrassing to have passengers in the vehicle. I have followed the recommended preventive measures, including replacing the cabin air filter, turning the A/C compressor off several minutes before shutting the vehicle off, and attempting to clean the HVAC system with commercially available products. None of these measures have resolved the issue. Based on discussions with other GMC Yukon owners, this appears to be a common and recurring problem affecting numerous vehicles of similar model years. Many owners report the same symptoms and repeated unsuccessful repair attempts. This suggests the issue may be related to the design or operation of the HVAC system, particularly moisture remaining on the evaporator core, rather than normal maintenance. I am requesting that GMC investigate this recurring defect and provide a permanent repair rather than temporary odor treatments. Owners should not have to repeatedly clean or service the HVAC system to address a condition that has existed since the vehicle was new.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11751904July 21, 2026
STRUCTURE, ELECTRICAL SYSTEM
The contact owns a 2024 GMC Yukon. The contact stated that there was a strong mildew odor coming from the vehicle while entering the vehicle, and there was moisture around the trunk near the wiring harness. The vehicle was taken to Modern Auto Company (6224 MO-100, Washington, MO 63090), but the cause of the failure was not found. O'Fallon Buick GMC (2150 Technology Dr, O'Fallon, MO 63368) diagnosed the vehicle with a failure of the wiring harness and stated that there was moisture entering the vehicle through the wiring harness. However, after the contact inquired about the odor inside the vehicle, the dealer refused to continue working with the contact. The manufacturer was notified of the failure, and a claim was filed, and an appointment was scheduled for service at Dave Sinclair Buick GMC (5655 S Lindbergh Blvd, St. Louis, MO 63123). The dealer informed the contact that the wiring harness appeared to have already been replaced. The dealer found no leaks inside the vehicle and informed the contact that the vehicle would be returned. The contact hired a mold expert to inspect the vehicle while the vehicle was at the dealer. The mold expert discovered several cases of toxic mold inside the vehicle and deemed the vehicle unsafe to drive. The contact stated that her daughter had severe respiratory issues and was transported in the vehicle. The daughter had several doctor’s visits, was put on several medications, and missed 40 days from school due to her illness. The contact associated the failure with her daughter's illness and stated that her daughter’s health improved once she was no longer transported in the vehicle. Since the failure, the contact had to pay out-of-pocket for a rental vehicle. A field investigator had been hired by the manufacturer to inspect the vehicle, and the contact was awaiting the results. The vehicle remained with the dealer unrepaired. The failure mileage was approximately 27,000.
Crash:
No
Fire:
No
Injuries:
1
Deaths:
0
#11751858July 21, 2026
ENGINE, FUEL/PROPULSION SYSTEM, STEERING
The engine tries to die when in park. While stopped at a red light, it died and stated conditions not met to shift. Had to hit park button then restart it. This has happened 4 times. With & without auto start feature on
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11751474July 20, 2026
ENGINE, FUEL/PROPULSION SYSTEM, UNKNOWN OR OTHER
I am reporting a serious safety defect and unreasonable delay in addressing it under safety recall N252494000 (L87 Engine – Loss of Propulsion). My GMC Yukon has an illuminated check engine light and is now also overheating. According to GM’s own customer service r, this can lead to knocking, unusual engine noises, hesitation, high RPMs, abnormal shifting, reduced propulsion, and sudden loss of propulsion while driving, increasing the risk of a crash. I have contacted multiple dealerships for urgent repair: Cappllino GMC Keller Chevrolet Joe Basil All three have advised me that they do not have enough technicians to get my vehicle in for repair. Each has urged me to continue driving the vehicle despite the active check engine light and recall, and all have refused to provide a loaner vehicle. I have also contacted GMC Corporate directly for intervention. Instead of providing a loaner or expediting repairs, they have only offered post-repair rental reimbursement (up to $44/day after a repair order is opened). This leaves me with no safe transportation option. I have been told I can “drop off” the vehicle, but I have no alternative way to get home or to work. GMC and its dealerships are putting my safety (and the safety of other road users) at serious risk by directing me to continue operating a recalled, overheating vehicle with an active check engine light while refusing to provide any loaner or timely repair. My vehicle has 34,700 miles and is nearing the end of its warranty coverage, which raises additional concerns about potential delay tactics. Please review: The L87 engine defect and related check engine/overheating issues in GMC Yukons. GMC’s handling of this recall, including widespread failure to provide loaners and instructions to customers to keep driving defective vehicles. I authorize the release of my contact information to GMC to assist with the investigation. Attachments I can provide: Screenshots of communications with GMC
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11751456July 20, 2026
ENGINE
The contact owns a 2021 GMC Yukon. The contact stated that while driving at slow speeds from 2 - 30 MPH, the vehicle hesitated and bucked while accelerating and switching between 4- and 8-cylinders operation. The vehicle was taken to the local mechanic who installed a part used to override the engine cylinder mode, and the engine only operated using 8 cylinders. No further information was available. The manufacturer and local dealer were not contacted about the failure. The failure mileage was 102,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11750859July 16, 2026
POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT
The contact owns a 2022 GMC Yukon. The contact stated that there was an abnormal moaning and grinding sound coming from the vehicle. The contact became aware of the uneven wear on the tires. There were no warning lights illuminated. The vehicle was taken to the local dealer, where it was diagnosed and determined that the differential needed to be replaced. The vehicle was not repaired. The vehicle previously had an alignment and fluid flush performed. The contact stated that the failure was related to TSB: 21-NA-028 – (Rear Differential Moan/Chatter). The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 39,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11750642July 15, 2026
ENGINE
am filing a formal complaint regarding my 2023 GMC Yukon Denali, which experienced a catastrophic engine failure while I was driving on the highway with my family. The sudden failure created a dangerous situation, placing both my family and me at significant risk. As a result of the breakdown, I was forced to pay $260 out of pocket to have the vehicle towed to the dealership. After inspecting the vehicle, the dealership advised me that the engine requires complete replacement. There was no indication that the engine was going to go. Thankfully there was a shoulder on the highway and we were able to pull over. This could have caused an accident could've been fatal.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11750311July 14, 2026
ENGINE, ELECTRICAL SYSTEM
Vehicle is a 2022 GMC Yukon Denali with the 6.2L L87 V8, covered by NHTSA Recall 25V-274 (GM N252494001). The recall remedy was performed. The engine passed the dealer inspection and was given the higher-viscosity 0W-40 oil remedy rather than an engine replacement. On 05/26/2026, at approximately 43,000 miles, the vehicle suffered a sudden engine knock while being driven by my wife. At the same time, the dash displayed Service ESC and Service Traction Control warnings, the vehicle's speed fluctuated on its own without driver input, and the air suspension cycled up and down while the vehicle was in motion. The vehicle had to be towed to the dealer. The dealer diagnosed a failed lifter with resulting camshaft damage and repaired it under the powertrain warranty. The vehicle was out of service approximately fifteen days. Shortly after the vehicle was returned, it began displaying a "Theft Attempted" message on the dash every day. I reported this to the dealer in writing on 06/15/2026 with a photograph at 43,898 miles. The dealer stated it was unlikely to be related and did not scan or diagnose it. On 07/14/2026, approximately 560 miles after the repair, the vehicle became inoperable and had to be towed to the dealer a second time. It is currently at the dealer and has not yet been diagnosed. The unexpected loss of power, speed fluctuation, and stability-control failure at road speed present a serious crash risk. This vehicle passed the 25V-274 inspection remedy and then experienced a valvetrain failure regardless, which is directly relevant to Recall Query RQ26001 into the adequacy of that remedy.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11750280July 14, 2026
ENGINE, FUEL/PROPULSION SYSTEM
Seems to be not accelerating properly as if the propulsion is not there. Also, when switching gears it seems as if it is slipping or missing to keep up with the propulsion. Lastly, riding with windows down on the highway alongside the concrete median, I can hear like metal clanking or rubbing against one another. Also, I get an oil change at George Ballas GMC on [XXX] and 3 weeks later truck says change oil soon. AND YES THEY RESET THE OIL LIGHT AND I DROVE IT FOR 3 WEEKS AND THE LIGHT POPPED ON!!!! INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11749937July 13, 2026
ENGINE
The contact owns a 2021 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle made an abnormal sound and failed to accelerate above 25 MPH. No warning light was illuminated. The vehicle was taken to an independent mechanic, who determined that there was metal in the engine and that the engine needed to be replaced. The vehicle was then taken to the dealer, where it remained for eight months before the engine was replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 127,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to GMC Yukon