Chevrolet Corvette Recalls

50 recalls on file.

• Recall14V299000June 6, 2014
  SEAT BELTS

  General Motors LLC (GM) is recalling certain model year 2014 Chevrolet Corvette vehicles manufactured April 23, 2014 to April 25, 2014. In the affected vehicles, the Sensing and Diagnostic Module (SDM) may experience an internal short circuit, resulting in the deactivation of the air bags and seat belt pretensioners.

  Remedy

  GM will notify owners, and dealers will replace the Sensing and Diagnostic Module (SDM), free of charge. The recall began on August 1, 2014. Owners may contact General Motors customer service at 1-800-222-1020. GM's number for this recall is 14219.

• Recall14V251000May 14, 2014
  EXTERIOR LIGHTING:HEADLIGHTS

  General Motors LLC (GM) is recalling certain model year 2005-2007 Chevrolet Corvette vehicles manufactured March 29, 2004, through June 22, 2007. In the affected vehicles, the underhood bussed electrical center (UBEC) housing can expand and cause the headlamp low beam relay control circuit wire to bend. If the wire is repeatedly bent, it may fracture causing a loss of low beam headlamp illumination.

  Remedy

  GM will notify owners, and dealers will install a jumper wire to correct this condition, free of charge. The recall began January 2, 2015. Owners may contact Chevrolet customer service at 1-800-222-1020. GM's number for this recall is 13146. Note: Model year 2008-2013 Chevrolet Corvettes will be covered under customer satisfaction program number 14203 for the same issue.

• Recall11V491000October 3, 2011
  STRUCTURE:BODY:HATCHBACK/LIFTGATE:HINGE AND ATTACHMENTS

  GENERAL MOTORS (GM) IS RECALLING CERTAIN MODEL YEAR 2011-2012 CHEVROLET CORVETTE COUPE VEHICLES, MANUFACTURED FROM JANUARY 24, 2011, THROUGH SEPTEMBER 1, 2011, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NUMBER 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS". THE REAR HATCH HINGES MAY NOT MEET THE LOAD REQUIREMENTS SPECIFIED IN THE SAFETY STANDARD.

  Remedy

  GM WILL NOTIFY OWNERS AND DEALERS WILL REPLACE BOTH REAR HATCH HINGES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 14, 2011. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438.

• Recall10V172000April 26, 2010
  STEERING:COLUMN

  GM IS RECALLING CERTAIN MODEL YEAR 2005 AND 2006 CHEVROLET CORVETTE PASSENGER CARS MANUFACTURED BETWEEN MARCH 2004 AND JANUARY 2006 EQUIPPED WITH A TILT AND TELESCOPING STEERING COLUMN (RPO N37). IN RARE CASES, REPEATED MOVEMENT OF THE STEERING COLUMN MAY CAUSE A SIGNAL INTERRUPTION WITHIN THE COLUMN. IF THIS OCCURS, THE MESSAGE, "SERVICE ACTIVE HANDLING SYSTEM" WILL APPEAR IN THE DRIVER INFORMATION CENTER, AND ONE OR MORE OF THE BRAKES MAY APPLY, POSSIBLY CAUSING THE VEHICLE TO PULL TO THE RIGHT OR LEFT.

  Remedy

  GM WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 30, 2010. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

• Recall09V491000December 23, 2009
  STRUCTURE:BODY:ROOF AND PILLARS

  GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2007 CORVETTE VEHICLES EQUIPPED WITH A REMOVABLE ROOF AND MODEL YEAR 2006 AND 2007 CORVETTE Z06 VEHICLES. THE ADHESIVE BETWEEN THE ROOF PANEL AND THE FRAME MAY SEPARATE. IF THERE IS A PARTIAL SEPARATION, THE DRIVER MAY NOTICE ONE OR MORE SYMPTOMS, SUCH AS A SNAPPING NOISE WHEN DRIVING OVER BUMPS, WIND NOISE, POOR ROOF PANEL FIT, ROOF PANEL MOVEMENT/BOUNCE WHEN A DOOR OR HATCH IS CLOSED, OR A WATER LEAK IN THE HEADLINER.

  Remedy

  DEALERS WILL INSTALL A NEW DESIGN ROOF PANEL FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING APRIL 2010. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR AT WWW.GMOWNERCENTER.COM.

• Recall09E025000May 11, 2009
  EXTERIOR LIGHTING:HEADLIGHTS

  DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

  Remedy

  DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

• Recall09E012000April 7, 2009
  EXTERIOR LIGHTING

  SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

  Remedy

  SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

• Recall07E088000October 24, 2007
  EQUIPMENT

  CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

  Remedy

  HONEYWELL WILL REPLACE THE AFFECTED OIL FILTERS FREE OF CHARGE. THE RECALL BEGAN DURING NOVEMBER 2007. OWNERS CAN CONTACT FRAM CUSTOMER SERVICE TOLL-FREE AT 1-800-890-2075.

• Recall06V181000May 24, 2006
  STRUCTURE:BODY:ROOF AND PILLARS

  ON CERTAIN 2005-2006 CHEVROLET CORVETTES EQUIPPED WITH PAINTED ROOFS, THE ADHESIVE BETWEEN THE ROOF PANEL AND THE FRAME MAY SEPARATE.

  Remedy

  DEALERS WILL INSPECT VEHICLES FREE OF CHARGE FOR POTENTIAL ROOF PANEL-TO- FRAME SEPARATION AND ADD THE SPECIFIED ADHESIVE FOAM OR REPLACE THE ROOF WITH ONE HAVING ADHESIVE FOAM. THE RECALL BEGAN ON OCTOBER 19, 2006. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438.

• Recall06E043000May 19, 2006
  FUEL SYSTEM, GASOLINE

  CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

  Remedy

  HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).

• Recall05V455000October 5, 2005
  STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS

  CERTAIN PASSENGER VEHICLES MAY HAVE BEEN BUILT WITH A POWER STEERING HOSE THAT IS NOT TO SPECIFICATION. UNDER EXTREME STEERING MANEUVERS, SUCH AS TURNING THE STEERING WHEEL FULLY TO THE LEFT OR RIGHT WHILE BRAKING, THE HOSE MAY FRACTURE AND LEAK FLUID.

  Remedy

  DEALERS WILL INSPECT THE POWER STEERING HOSE(S) FOR TWO SUSPECT DATE CODES AND REPLACE THEM IF REQUIRED. THE RECALL WILL BEGIN ON OCTOBER 14, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463, BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, ISUZU AT 1-800-255-6727, OR HUMMER AT 1-800-732-5493.

• Recall04V525000November 3, 2004
  SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

  CERTAIN PASSENGER VEHICLES WERE PRODUCED WITH ONE OR BOTH REAR BRAKE HYDRAULIC LINES THAT CAN COME IN CONTACT WITH OR BE AFFECTED BY HEAT FROM THE LEFT ENGINE EXHAUST MANIFOLD AND THE LEFT EXHAUST PIPE. THE BRAKE FLUID COULD REACH ELEVATED TEMPERATURES AND BOIL.

  Remedy

  DEALERS WILL (1) INSPECT THE LEFT ENGINE EXHAUST MANIFOLD CLIP FOR PROPER ALIGNMENT AND PLACEMENT ON THE BODY-MOUNTED STUD. IF INCORRECT, THEY WILL REPOSITION THE CLIP ON THE BRAKE LINES AND REINSTALL THE CLIP ON THE STUD; (2) THE DEALER WILL VERIFY THAT BOTH REAR BRAKE LINES HAVE THE PROPER CLEARANCE TO THE LEFT EXHAUST PIPE. THEY WILL REPOSITION THE LINES BY BENDING AS NECESSARY; (3) DEALERS WILL REMOVE THE MACHINING TAB FROM THE REAR DIFFERENTIAL HOUSING. ALSO, DEALERS ARE TO INSPECT THE BRAKE LINES FOR WEAR IN THESE RELATED AREAS AND REPAIR OR REPLACE IF THERE IS ANY SIGN OF WEAR-THROUGH ON THE NYLON OVERCOATING. THE RECALL BEGAN ON JANUARY 18, 2005. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2239 OR CHEVROLET AT 1-800-630-2438.

• Recall04V273000June 9, 2004
  STEERING:LINKAGES

  ON CERTAIN PASSENGER VEHICLES INVOLVED IN THIS CAMPAIGN, THE LOWER CONTROL ARM BALL STUD NUT/WASHER ASSEMBLIES WITH WASHERS WERE MADE OF THE WRONG MATERIAL. THE WASHERS MAY FRACTURE AND BECOME LOOSE OR FALL AWAY FROM THE VEHICLE, REDUCING CLAMP LOAD. SEPARATION OF THE CONTROL ARM BALL STUD AND STEERING KNUCKLE, DUE TO DISENGAGEMENT OF THE TAPERED ATTACHMENT AND RETAINING NUT, IS POSSIBLE.

  Remedy

  DEALERS WILL INSPECT THE BALL STUD JOINTS AND MEASURE THE TORQUE OF THE NUT FOR ALL FRONT LOWER CONTROL ARMS IN ALL MODELS AFFECTED AS WELL AS THE REAR LOWER CONTROL ARMS ON THE XLR AND CORVETTE. IF THE TORQUE IS NOT AT SPECIFICATION, THE DEALERS WILL REPLACE THE BALL STUD, THE KNUCKLE, AND THE NUT. IF THE TORQUE IS AT SPECIFICATION, THE DEALERS WILL REPLACE THE NUT/WASHER ASSEMBLY ONLY. THE RECALL WILL BEGIN ON AUGUST 25, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339 OR CHEVROLET AT 1-800-630-2438.

• Recall04V060000February 9, 2004
  STEERING:COLUMN LOCKING:ANTI-THEFT DEVICE

  ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH ELECTRONIC COLUMN LOCK SYSTEMS (ECL), WHEN THE IGNITION SWITCH IS TURNED TO "LOCK," THE ECL SYSTEM PREVENTS TURNING OF THE STEERING SYSTEM. WHEN THE VEHICLE IS STARTED, THE ECL UNLOCKS THE STEERING SYSTEM. THE VEHICLE IS DESIGNED SO THAT IF THE COLUMN FAILS TO UNLOCK WHEN THE VEHICLE IS STARTED AND THE CUSTOMER TRIES TO DRIVE, THE FUEL SUPPLY WILL BE SHUT OFF SO THAT THE VEHICLE CANNOT MOVE WHEN THE VEHICLE CANNOT BE STEERED. IF VOLTAGE AT THE POWERTRAIN CONTROL MODULE IS LOW OR INTERRUPTED, HOWEVER, THE FUEL SHUT OFF MAY NOT OCCUR AND THE VEHICLE CAN BE ACCELERATED WHILE THE STEERING SYSTEM IS LOCKED. ALSO WHEN THE CONTROL SYSTEM SHOWS THAT THE ECL IS UNLOCKED AND THE VEHICLE IS BEING DRIVEN, THE LOCK PIN LOCATION CAN VARY. DEPENDING ON THE LOCATION OF THE LOCK PLATE RELATIVE TO THE SWITCH TRANSITION POINT, THERE COULD THEN BE CONTACT BETWEEN THE LOCK PLATE AND PIN CAUSING THE STEERING TO LOCK WHILE DRIVING .

  Remedy

  ON VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSMISSION, THE DEALER WILL DISABLE THE STEERING COLUMN LOCK BY REMOVING THE COLUMN LOCK PLATE. WHEN THE IGNITION KEY IS REMOVED, THE TRANSMISSION SHIFTER WILL LOCK BUT THE STEERING COLUMN WILL NOT LOCK. ON VEHICLES EQUIPPED WITH A MANUAL TRANSMISSION, THE DEALER WILL REPROGRAM THE POWERTRAIN CONTROL MODULE, PERFORM A DIMENSIONAL CHECK OF THE COLUMN LOCK AND, IF NECESSARY, REPLACE THE LOCK PLATE. THE STEERING COLUMN ON THESE VEHICLES WILL CONTINUE TO LOCK WHEN THE KEY IS REMOVED. OWNER NOTIFICATION TO OWNERS OF 1997 VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS BEGAN ON APRIL 26, 2004. OWNERS OF 1998 THROUGH 2004 VEHICLES (EXCEPT 1997-1998 MANUAL TRANSMISSION VEHICLES) WILL BE NOTIFIED BEGINNING ON AUGUST 2, 2004. THE REMAINING OWNERS (1997-1998 MANUAL TRANSMISSION VEHICLES) WILL BE NOTIFIED LATER IN 2004, WHEN PARTS ARE AVAILABLE. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438.

• Recall03E032000May 12, 2003
  SERVICE BRAKES, AIR:DISC:CALIPER

  REMANUFACTURERD REAR BRAKE CALIPERS, PART NOS. 18-7019, 18-7020, 16-7019, AND 16-7020, MANUFACTURED FROM FEBRUARY 1, 2002, TO APRIL, 25, 2003., AND FOR USE ON 1965 THRU 1982 CHEVROLET CORVETTES. THE SUBJECT BRAKE CALIPERS WERE MANUFACTURED USING IMPROPERLY MANUFACTURED PISTON SEALS. THESE SEALS ARE INTENDED TO PREVENT FLUID LEAKAGE BETWEEN THE CALIPER HOUSING AND THE PISTONS. THESE BRAKE CALIPERS ARE FOR USE ONLY ON 1965 THRU 1982 CHEVROLET CORVETTE VEHICLES. THIS RECALL DOES NOT INVOLVE GENERAL MOTORS CORPORATION OR ANY OF ITS PRODUCTS.

  Remedy

  CARDONE WILL NOTIFY ITS CUSTOMERS AND ALL UNSOLD INVENTORY WILL BE REPURCHASED AND WILL PROVIDE A FULL REFUND TO CUSTOMERS. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING MAY 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CARDONE AT 215-912-3000.

• Recall00V111000April 17, 2000
  SEAT BELTS:FRONT

  VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LAP BELT WEBBING CAN TWIST ALLOWING THE WEBBING TO BECOME JAMMED IN THE RETRACTOR.

  Remedy

  DEALERS WILL INSTALL INSERTS TO THE BELT WEB GUIDE OF EACH LAP BELT RETRACTOR.

• Recall97V104000June 28, 1997
  SEAT BELTS:FRONT:ANCHORAGE

  VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SEAT BELTS IN THESE VEHICLES INCORPORATE AN ENERGY MANAGEMENT LOOP. THIS LOOP IS INADEQUATE TO ABSORB THE NECESSARY FORCES THAT CAN BE EXERTED ON IT. THEREFORE, THE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

  Remedy

  DEALERS WILL REPLACE THE DRIVER AND PASSENGER SIDE SEAT BELT RETRACTOR ASSEMBLIES.

• Recall97V105000June 23, 1997
  FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY

  VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE A TORN FUEL TANK SENDING UNIT/PUMP SEAL. THIS CAN CAUSE FUEL ODOR AND/OR LEAKAGE AT THE ATTACHMENT LOCATION.

  Remedy

  DEALERS WILL REPLACE THE LEFT AND RIGHT HAND FUEL TANK ASSEMBLIES (INCLUDING FUEL SENDING UNIT AND PUMP).

• Recall97V044000March 20, 1997
  SUSPENSION:REAR

  THE REAR SUSPENSION TIE ROD ASSEMBLY CAN FRACTURE.

  Remedy

  DEALERS WILL REPLACE THE LEFT AND RIGHT-HAND REAR SUSPENSION TIE ROD LINKS.

• Recall92V160000November 8, 1992
  STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS

  THE POWER STEERING GEAR INLET HOSE ON THESE VEHICLES CAN FRACTURE, CAUSING POWER STEERING FLUID TO SPRAY FROM HOSE INTO THE ENGINE COMPARTMENT.

  Remedy

  REPLACE THE POWER STEERING GEAR INLET HOSE WITH AN IMPROVED DESIGN.