BMW 328i Service Bulletins
739 manufacturer communications on file.
- October 1, 2015•Document ID: 10147769Service Bulletin/Repair InstructionsPOWER TRAIN:AXLE ASSEMBLY
- Mfr Comm. #:
- B330215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
Associated Products (34)Associated Documents - October 1, 2015•Document ID: 10147760Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B111415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThe plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
Associated Products (22)Associated Documents - October 1, 2015•Document ID: 10147758Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B070314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - September 1, 2015•Document ID: 10147272Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B840515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive Messages Are Not Received In the Vehicle. One or both of the following may occur: SMS based messages are not received in the vehicle. These are: Text messages - Office feature MyInfo Google send to car - addresses and Points of Interests (POI) Concierge The activation code is not accepted by the ConnectedDrive Portal. Software error in the HU-H (Head unit High).
Associated Products (28)Associated Documents - September 1, 2015•Document ID: 10147271Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B840315
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"HU-B: Bluetooth Connection Fails Sporadically. The Bluetooth system works intermittently. One or more of the following scenarios may occur: Bluetooth pairing is not possible - display shows ""Please wait"" Unable to select the check box to activate Bluetooth Device does not reconnect to the vehicle after a key cycle Audio interference noise is heard listening to iPod etc. When trying to access the user manual, the display shows ""Please wait"" Incorrect software installed in the HU-B (Headunit Basic)."
Associated Products (33)Associated Documents - September 1, 2015•Document ID: 10147268Service Bulletin/Repair InstructionsLANE DEPARTURE: LANE KEEP: STEERING ASSIST
- Mfr Comm. #:
- B660515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryParking Maneuvering Assistant and Park Distance Control Failure. After activating the PMA (Parking Maneuvering Assistant) or PDC (Park Distance Control), the system stops functioning and a CCM (Check Control Message) is displayed advising the driver of the failure. The following fault code is stored in the PMA control unit 0x481E4D - PMA control unit internal, internal ASIC fault Software error in the PMA control unit Affected I-Level: F2x from F020-15-03-500 F3x from F020-15-07-500
Associated Products (19)Associated Documents - September 1, 2015•Document ID: 10147264Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640715
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryIHKA - Outlet Temperature is Different on Both Sides. The IHKA settings on the left- and right-hand side are identical. The outlet temperature for both sides is different. Software application error in IHKA.
Associated Products (32)Associated Documents - September 1, 2015•Document ID: 10147263Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"IHKA - Blower Runs in Emergency Mode. After the ignition is turned off and the vehicle is locked, the heating and air conditioning blower motor runs continuously. The next time the vehicle is started there may be the CCM (Check control message) displayed for ""Increased battery discharge"". CAUSE The blower output stage receives an invalid LIN bus signal during operation and switches to emergency mode. The blower will continue to run with the specified emergency mode after the ignition is turned off and the vehicle is locked."
Associated Products (34)Associated Documents - September 1, 2015•Document ID: 10147262Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryIHKA - Recirculation Function Changes from Manual to Automatic. While driving, the air recirculation button on IHKA changes by itself from manual to automatic or automatic to manual mode. CAUSE The IHKA operating software is too sensitive.
Associated Products (34)Associated Documents - September 1, 2015•Document ID: 10147259Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:BACK UP LIGHTS
- Mfr Comm. #:
- B630515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Reverse Light is Intermittently Inoperative. CCM (Check control message) is displayed indicating a ""reverse light"" is out. CAUSE There is a weak spring in bulb socket or bulb carrier (on the luggage compartment lid) which is causing a bad contact with the bulb."
Associated Products (24)Associated Documents - September 1, 2015•Document ID: 10147252Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY
- Mfr Comm. #:
- B512715
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Under certain conditions, the additional radiator could not be cooled sufficiently. This could cause the engine to overheat. The engine power would be reduced and a Check Control Message would appear. AFFECTED VEHICLES This Delivery Stop involves F34 (3 Series Gran Turismo) produced from July 13, 2015 to July 18, 2015. Vehicles which require this Delivery Stop to be completed will show it as ""Open"" when checked either in AIR, the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Associated Products (8)Associated Documents - September 1, 2015•Document ID: 10147251Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- B512615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDriver or Passenger's Front Doors Handles Inoperable. Sporadically it is not possible to open the driver or passenger's front door from the outside or inside door handle. Multiple attempts will eventually open the door. Comfort access operation of the outside door handle works properly. This situation occurs at temperatures below 37 °F. CAUSE Incorrect routing of the Bowden cable.
Associated Products (24)Associated Documents - September 1, 2015•Document ID: 10147250Service Bulletin/Repair InstructionsSTRUCTURE; VISIBILITY:REARVIEW MIRRORS/DEVICES; VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- B512415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryGroaning Noise from the Exterior Mirror. A groaning noise is heard coming from the area around the outside mirror when opening and closing the door. The noise is more noticeable when the door is fully open to the end stop. CAUSE The outer front door weather strip rubs against the mirror housing.
Associated Products (16)Associated Documents - September 1, 2015•Document ID: 10147249Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- B512315
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryThe Driver's Door Can No Longer Be Opened from the Outside. The driver's door cannot be opened from the outside by the door handle. The door still can be opened from the inside. CAUSE The Bowden cable has become detached.
Associated Products (22)Associated Documents - September 1, 2015•Document ID: 10147243Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- B360115
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCheck Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Associated Products (49)Associated Documents - September 1, 2015•Document ID: 10147242Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC
- Mfr Comm. #:
- B340414
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Associated Products (100)Associated Documents - September 1, 2015•Document ID: 10147241Service Bulletin/Repair InstructionsWHEELS; POWER TRAIN:DRIVELINE
- Mfr Comm. #:
- B270415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryShudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Associated Products (176)Associated Documents - September 1, 2015•Document ID: 10147235Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE
- Mfr Comm. #:
- B111615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
Associated Products (73)Associated Documents - August 1, 2015•Document ID: 10151415Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- B620515
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"Instrument Cluster: CBS ""Running-in Check"" is Displayed. After replacing and / or programming the instrument cluster with ISTA/P 3.55.0 or higher (integration Level F020-15-03-501 or higher), the CBS (Condition Based Service) displays ""running-in check"" or ""1200 mile service is due"". The parameters of the CBS scopes for oil service, brake fluid, etc, can also be implausible or invalid. CAUSE Error in the CBS mapping data in the FEM (Front Electronics Module) and corrupt data in the instrument cluster during programming."
Associated Products (34)Associated Documents - August 1, 2015•Document ID: 10151404Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B270315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryVibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
Associated Products (142)Associated Documents