MINI Cooper Service Bulletins (2019)
150 manufacturer communications on file.
- January 1, 2017•Document ID: 10150987Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE
- Mfr Comm. #:
- M120916
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary?ENGINE MAY RUN ROUGH AFTER MSA ENGINE RESTART. Unfavorable DME software. Program and recode the vehicle using the latest version of ISTA.
Associated Products (7)Associated Documents - January 1, 2017•Document ID: 10150986Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- M120815
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary?REDUCED ENGINE POWER WITH EXHAUST CAMSHAFT SENSOR FAULT STORED. DME software error or incorrect oil viscosity. Ensure that the engine oil level is correct and no other VANOS or oil pressure faults are present.
Associated Products (6)Associated Documents - December 1, 2016•Document ID: 10146800Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- M111316
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryService Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.
Associated Products (7)Associated Documents - June 1, 2016•Document ID: 10151390Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT
- Mfr Comm. #:
- M640216
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryAir Conditioning Refrigerant R1234yf Introduction. INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipment may be an indication of refrigerant/equipment incompatibility with the vehicle's system. Always carefully ascertain the type of refrigerant used in the vehicle's system before performing service. Labels on underside of hood, will detail which refrigerant is used in the air conditioning system. Service the vehicle with compatible recycling equipment ONLY. Attempts to adapt and use incompatible service tools will destroy both the vehicle's air conditioning system and the service tool. Never use any R-12/R134a service tools on R1234yf systems. Tools, such as manifold gauge sets, retain small amounts of refrigerant and lubricant. Attempting to use the same equipment on both R-12/R134a and R1234yf vehicles will contaminate the air conditioning systems. Obtain and use the correct type of refrigerant recovery/recycling machine. Follow the directions included in the machine's instruction manual. WARR
Associated Products (8)Associated Documents - June 1, 2016•Document ID: 10151389Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- M620515
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryThe Clock in the Instrument Cluster Loses time This Service Information Bulletin supersedes SI M62 05 15 dated June 2016. The time displayed in the instrument cluster (KOMBI) may lose a few minutes each week and the clock needs to be adjusted periodically.
Associated Products (8)Associated Documents - June 1, 2016•Document ID: 10151388Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- M120815
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary"INFORMATION Covered under the terms of the MINI New Passenger Car Limited Warranty or the MINI NEXT Certified Pre-Owned Limited Warranty. This repair is also covered by the terms of the State-specific Emissions Warranty (dependent on the vehicle's model year, state of registration and its inclusion on the ""model-specific"" list of covered components). The MINI NEXT Certified Pre-Owned Limited Warranty applies to MINI vehicles that have and are still within the MINI NEXT Certified Pre-Owned Limited Warranty coverage period, but beyond the Emissions Warranty coverage that applies. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Coding Control module failures that occur during programming: Please claim these consequential repairs under the defect code listed in this bulletin and use the applicable KSD2 labor operations. Other Repairs Control module failures that occur prior to programming: When covered under an applicable limited warranty, claim these repairs using the applicable defect code and labor operations in KSD2. "
Associated Products (6)Associated Documents - June 1, 2016•Document ID: 10151386Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- M110916
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryVANOS AND VANOS CENTRAL BOLT IDENTIFICATION. INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.
Associated Products (8)Associated Documents - May 1, 2016•Document ID: 10151349Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- M840114
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryBluetooth Connection Failures This Service Information bulletin supersedes SI M84 01 14 dated February 2016.. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware
Associated Products (25)2019 MINI Cooper2018 MINI Cooper2017 MINI Clubman2017 MINI Cooper2016 MINI Cooper2016 MINI Cooper Convertible2016 MINI Countryman2015 MINI Cooper2015 MINI Countryman2014 MINI Clubman2014 MINI Cooper2014 MINI Countryman2013 MINI Clubman2013 MINI Cooper2013 MINI Cooper Coupe2013 MINI Cooper Roadster2012 MINI Cooper2012 MINI Cooper Coupe2012 MINI Cooper Roadster2011 MINI Cooper+ 5 moreAssociated Documents - May 1, 2016•Document ID: 10151348Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE
- Mfr Comm. #:
- M660216
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryCollision warning and Pedestrian Warning Failed. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed CAUSE The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield, And/ or The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. KAFAS camera mounting bracket not secured correctly to the windshield. Notice the spacing between the white outline and the bracket. Possible solutions: Verify the KAFAS camera is installed (seated) properly in its bracket Replace the KAFAS camera Replace the windshield
Associated Products (8)Associated Documents - May 1, 2016•Document ID: 10151346Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- M120316
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary"Service Action: Program Control Units (DME - VANOS). If the engine has been off for long period of time, when started it may run very rough at idle with the Service Engine Soon (MIL) light on. The engine power is reduced and a Check Control Message (CCM) ""Drive Faulty; Drive at moderate speed"" is also displayed. If the engine is then stopped and restarted the problem would no longer be present."
Associated Products (6)Associated Documents - April 1, 2016•Document ID: 10151294Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- M610116
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryFront Windshield Wiper Noises. Customer complains wipers are noisy or chattering during wiper operation. CAUSE Wiper arms out of adjustment and/or windshield cowl misaligned.
Associated Products (8)Associated Documents - April 1, 2016•Document ID: 10151293Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- M510316
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryAir Intake Makes Rattle Noise At Engine Idle. Engine has rattle noise from engine compartment. Check Hyperlink for video of rattle noise at engine idle. http://tinyurl.com/zwb8e6s Worn buffer in the battery tray
Associated Products (7)Associated Documents - April 1, 2016•Document ID: 10151292Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- M121214
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary"VANOS Faults Stored in DME (Bosch). The Service Engine Soon (MIL) is on and the engine could go into a reduced power mode with the ""Drivetrain Malfunction"" message displayed. One or more of the VANOS faults (listed in the attachment) are stored in the DME, although the engine is mechanically sound and no unusual noises can be heard from the VANOS area. Due to unfavorable Engine Position Management (EPM) parameters in the DME software, various VANOS control faults could be set. These control faults relate to implausible camshaft position (intake or exhaust), the camshaft stuck situation, or the camshaft angle offset to crankshaft outside the tolerance range."
Associated Products (4)Associated Documents - April 1, 2016•Document ID: 10151289Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- M110816
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryB38, B46 and B48 Engines: Engine and Cylinder Head Replacement Procedures. The engine may run rough and exhibit an engine noise from the VANOS area after the cylinder head or the engine is replaced.
Associated Products (3)Associated Documents - April 1, 2016•Document ID: 10151288Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- M110715
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary"This Service Information bulletin and attachment supersedes SI M11 07 15 dated October 2015.. Excessive amount of water condensation may accumulate in the engine's crankcase. With prolonged vehicle storage, water condensation in engine's oil may cause oil pump malfunction. AFFECTED VEHICLES This Service Action involves F55 and F56 models (MINI Cooper with the B38 engine) produced from 07/05/2014 to 02/24/2015 that are: Still a ""new vehicle"" in dealer inventory (no in-service date reported), and the Current odometer mileage is 155 or less. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Increased number of colds starts and stops during a vehicle's transportation and storage process (prior to customer delivery)."
Associated Products (7)Associated Documents - April 1, 2016•Document ID: 10151287Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- M110416
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary"The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""396"" F55 and F56 vehicles produced from January 2014 to February 2015. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"
Associated Products (5)Associated Documents - February 1, 2016•Document ID: 10151154Service Bulletin/Repair InstructionsENGINE; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- M110516
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummarySI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
Associated Products (5)Associated Documents - February 1, 2016•Document ID: 10151153Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ENGINE
- Mfr Comm. #:
- M110416
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummarySI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
Associated Products (5)Associated Documents - February 1, 2016•Document ID: 10151152Service Bulletin/Repair InstructionsENGINE; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- M110316
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummarySI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
Associated Products (5)Associated Documents - February 1, 2016•Document ID: 10151150Service Bulletin/Repair InstructionsENGINE; EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN
- Mfr Comm. #:
- M110216
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
Summary"SI M11 02 16 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 02 16 dated February 2016.. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""382"" F55 and F56 vehicles produced from February 2014 to December 2014. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"
Associated Products (5)Associated Documents