Mercedes-Benz S-Class Service Bulletins

741 manufacturer communications on file.

• October 14, 2025•Document ID: 11024358

  Service Bulletin/Repair Instructions
  WHEELS; SUSPENSION

  Mfr Comm. #:

  LI40.10-P-059248

  Date Added:

  October 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

  Associated Products (55)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class+ 35 more
  Associated Documents

  • DownloadMC-11024358-0001.pdf↗
• October 10, 2025•Document ID: 11024274

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 14, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

  Associated Products (53)

  2026 Mercedes-Benz CLA-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class+ 33 more
  Associated Documents

  • DownloadMC-11024274-0001.pdf↗
• September 25, 2025•Document ID: 11023347

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-071499

  Date Added:

  September 25, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

  Associated Products (114)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE+ 94 more
  Associated Documents

  • DownloadMC-11023347-0001.pdf↗
• September 19, 2025•Document ID: 11023207

  Service Campaign
  POWER TRAIN

  Mfr Comm. #:

  NCU - 2025090003

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the software for the powertrain control unit (PTCU) does not correspond to the current series production configuration. The possibility exists that a control unit timeout may occur followed by malfunction indicator lamp (MIL) activation. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the PTCU software in the affected vehicles.

  Associated Products (2)

  2022 Mercedes-Benz S-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11023207-0001.pdf↗
• September 17, 2025•Document ID: 11023209

  Service Bulletin/Repair Instructions
  SUSPENSION

  Mfr Comm. #:

  LI32.50-P-079670

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Concern 1 - Noises in recovery mode with the vehicle stationary Concern 2 - Noises when driving in a straight line on rough terrain Concern 3 - Noises when cornering and performing alternate steering movements Concern 4 - Non-assignable noises Cause Concern 1 - Noises in recovery mode with the vehicle stationary Concern 2 - Noises when driving in a straight line on rough terrain. These are normal operating noises of the hydraulic high-pressure pumps. Explanation: This is the "preview noise" which is heard when recovery mode is in operation, but which can also occur when driving over very uneven ground in the Comfort and Curve drive programs. This is a normal operating noise which is caused by the hydraulic high-pressure pumps (MPE). To compensate for the unevenness of the ground, large oil flows need to be generated and to do so, the MPEs turn at very high rotational speeds. Note: In the "ECO" drive program, the "Preview" function is deactivated so these noises should not occur when driving over uneven terrain; however the vehicle body will move noticeably. Concern 3 - Noises when cornering and performing alternate steering movements - reversing noise. Repeated rapid steering out of a curve generates a "grunting" noise. Explanation: This noise is caused by the MPEs when the pump's direction of rotation is reversed. Note: The reversing noise can occur in all drive programs, but is most clearly reproducible in the Curve drive program and in Curve level 3. Carry out an evaluation firstly in Curve levels 1 to 3 (at the highest Curve level 3, the noise will also be at its loudest!), and then in the Comfort drive program. Concern 4 - Non-assignable noises. Remedy Generally check whether the same noises also occur in ECO mode - in this mode the Preview/ROAD SURFACE SCAN function is deactivated and the high-pressure pumps run at reduced speed. Consequently, it is possible to differentiate between normal operating noises and unusual noises. Regarding 1, 2: Explain the high-pressure system, replacing the suspension struts or pumps is not useful, as these noises are caused by the high-pressure pump unit and should be regarded as normal operating noises. Regarding 3: This is currently a normal operating noise and represents the series production configuration; consequently replacing the components is not useful. Regarding 4: There will certainly be other unknown noises that we are not yet familiar with; therefore please report these as well. For these, create a TIPS case and include informative video recordings of the noises. The driving situation in the drive program in which the noises occur should be shown. For comparison, also attach a recording of this same driving situation in ECO mode. Additional attachments required: - Logs for control units N51/8, M67, M67/1, M67/2, M67/3. - Actual values for the pressures of the four hydraulic high-pressure pumps at standstill.

  Associated Products (17)

  2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2022 Mercedes-Benz S-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2021 Mercedes-Benz S-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class
  Associated Documents

  • DownloadMC-11023209-0001.pdf↗
• September 17, 2025•Document ID: 11023193

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-072588

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

  Associated Products (143)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class+ 123 more
  Associated Documents

  • DownloadMC-11023193-0001.pdf↗
• September 16, 2025•Document ID: 11023192

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI00.00-P-079603

  Date Added:

  September 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The OTA software update prepares the SRS/ORC controller and enables it to be updated remotely in the future. Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 (N2/5 -Supplemental Restraint System SRS) using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

  Associated Products (8)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11023192-0001.pdf↗
• September 13, 2025•Document ID: 11023107

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2025080007

  Date Added:

  September 12, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the High Voltage Battery (“HVB”) AC charger software does not correspond to current production specifications. As a consequence, a HVB MIL may illuminate during charging due to fluctuations in power consumption of the charging socket actuator. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the HVB AC Charger Software.

  Associated Products (22)

  2025 Mercedes-Benz C-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz S-Class+ 2 more
  Associated Documents

  • DownloadMC-11023107-0001.pdf↗
• September 11, 2025•Document ID: 11023153

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI47.70-P-076030

  Date Added:

  September 17, 2025

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Complaint After the charging process is complete, an instrument cluster message with a charging error appears and FC P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 167, 214, 254 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software is currently in development and will become available in 11/2025. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Please inform the workshop to perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

  Associated Products (13)

  2025 Mercedes-Benz C-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz S-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11023153-0001.pdf↗
• September 11, 2025•Document ID: 11023103

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-079772

  Date Added:

  September 12, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After a software update of component LIB48_222 - G1/3 (48 V on-board electrical system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.

  Associated Products (41)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLE-Class+ 21 more
  Associated Documents

  • DownloadMC-11023103-0001.pdf↗
• September 10, 2025•Document ID: 11023096

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.31-P-066469

  Date Added:

  September 11, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Possible humming noises from the drivetrain in the area of the rear axle, especially during tight cornering in the lower speed range. Remedy Note: Please follow the instructions in this document. The replacement of components (other than those named for processing) is not effective. Remedy: A test drive must be performed. For accurate analysis (localization) of the noise, the "Steelman Chassis Ear" noise diagnosis kit can be used, for example. If the rear axle differential is unambiguously identified as the cause (noise source), the oil must be replaced. Observe the following: 1. Warm up the oil in the differential by means of a short test drive. 2. Drain the oil from the differential and fill it with new oil according to the parts list in the attachment. Please follow the procedure described in AR.35.31-P-0523OLC. Note: To ensure that the differential is drained as completely as possible, both rear wheels should be rotated slowly 2-3 turns while draining. Make sure that as little residual oil as possible remains in the differential. 3. Please advise the customer that in isolated cases the problem may continue to occur for another 30 to 60 miles after the oil has been replaced. If the problem is still present after the appropriate mileage: • Double check the appropriate mileage was driven. • Repeat the flushing and filling procedure a second time, make sure to properly flush all the diff fluid out • If no change after the second flush and additional mileage. replace the rear diff

  Associated Products (11)

  2018 Mercedes-Benz C-Class2018 Mercedes-Benz E-Class2018 Mercedes-Benz GLC-Class2018 Mercedes-Benz S-Class2018 Mercedes-Benz SLC-Class2017 Mercedes-Benz C-Class2017 Mercedes-Benz E-Class2017 Mercedes-Benz GLC-Class2017 Mercedes-Benz S-Class2017 Mercedes-Benz SLC-Class2017 Mercedes-Benz SLK-Class
  Associated Documents

  • DownloadMC-11023096-0001.pdf↗
• September 10, 2025•Document ID: 11023050

  Service Bulletin/Repair Instructions
  SUSPENSION

  Mfr Comm. #:

  LI32.35-P-079752

  Date Added:

  September 10, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Shock symbol in instrument cluster with "Do Not Drive Over 50MPH" message AND DTC's in A108/2 or A108/3: U013281 - Communication with control unit "Suspension" has a malfunction. Incorrect data were received. C156F00 - The signal values of the level sensors are implausible. Cause Physical layer wiring to the level control sensors B22/X. Remedy Check A108/2 and A108/3 for freeze frame data section "ZF_error_handler". The text will provide a good place to start. Example: "SPC_FEHLER_VehLvl_Stat_HP_AMG_AR2_SNA_VehLvl_RR_V2_AMG" indicates the Right Rear may have initiated the DTC. See attached picture for reference. Use Hioki to measure wiring to all four level sensors. Use above DTC freeze frame data to inspect specific wiring. In some instances, level sensors may rectify concern although wiring to a different level sensor may be the cause. If vehicle exhibits concern after all of the above is completed, please open a TIPS case to the Body, Chassis, Entertainment Inbox.

  Associated Products (14)

  2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2020 Mercedes-Benz GLS-Class
  Associated Documents

  • DownloadMC-11023050-0001.pdf↗
• September 8, 2025•Document ID: 11023033

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI00.00-P-079603

  Date Added:

  September 9, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The OTA software update prepares the SRS/ORC controller and enables it to be updated remotely in the future. Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

  Associated Products (12)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz S-Class2021 Mercedes-Benz GLC-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz GLC-Class
  Associated Documents

  • DownloadMC-11023033-0001.pdf↗
• September 5, 2025•Document ID: 11022923

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI80.20-P-078308

  Date Added:

  September 8, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint One of the flush door handles (Also referred to as Seamless Door Handles) does not extend/retract (and/or) the KeylessGo sensor surfaces do not respond. Cause Multiple possible causes can be inferred from the table, see remedy (additionally as reference table in attachment). Remedy 1) KeylessGo sensor surfaces do not respond. Door handles can extend/retract if the key is used for locking/unlocking. No particular fault code. Perform an A17/x (handle controller) reset via XENTRY (for example see attachment - under actuations tab for A17/x controller) -> add-on is available (add-on 32204 for XENTRY version 06/25) Please use one of the following damage codes: 8213H; 82197; 8213K; 82198 2) Surface-flush door handle fails to retract and/or extend One or more of the following fault codes are current and stored: B185D96; B185E96; B186196; B186296 A control unit event log for the component part concerned (A17/x) must be created and the following values checked in the "Component Errors" section: Motor_bridge_connection_fatal_error = True (for example, see attachment) OR Motor_bridge_wrong_direction_fatal_error = True (for example, see attachment) If one of the values is "True": Perform an SCN coding on the door handle A17/x via XENTRY -> add-on is available (add-on 32280 for XENTRY version 06/25) The faults must be deleted after SCN coding. Please use one of the following damage codes: 80A0F; 80N0F; 80N0G; 80A0G 3) Surface-flush door handle fails to retract and/or extend One or more of the following fault codes are current and stored: B185D96; B185E96; B186196; B186296 A control unit event log for the component part concerned (A17/x) must be created and the following value checked in the "Component Errors" section: Motor_init_error_for_sensors = True (for example, see attachment) If the value is "True" Bearing bracket must be replaced. Please use one of the following damage codes: 80A0F; 80N0F; 80N0G; 80A0G 4) Surface-flush door handle fails to retract and/or extend The fault code B185911 is stored in the DCU (N69/X). The motor resistance is too low. Bearing bracket must be replaced. Please use one of the following damage codes: 80A0D; 80N0D; 80N0E; 80A0E If after the remedy points above are performed and the problem is still present, then please create a TIPS case and direct to the Body/Chassis/Entertainment inbox. Include your control unit logs, photos/videos, and quick tests to show diagnosis performed thus far. -> In this case, store the damaged parts for further analyses.

  Associated Products (6)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11022923-0001.pdf↗
• September 4, 2025•Document ID: 11023026

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.62-P-077311

  Date Added:

  September 9, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint No audio is output either in radio mode, or with media playback via app, Bluetooth or USB. In such cases, "Playback not active" is shown in the display. Cause Mute line between communication module N112/2 and sound control unit N40/3. Remedy Check the mute cable between control units N112/2 (communication module) and N40/3 (sound system). • Inspect the cable and plug contacts for damage or deformation. • Repair or replace the cable as needed. Important: If any plug contact is found to be deformed, you must also inspect the corresponding connector on the control unit to ensure it is not compromised.

  Associated Products (41)

  2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class+ 21 more
  Associated Documents

  • DownloadMC-11023026-0001.pdf↗
• August 29, 2025•Document ID: 11022209

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2025080003

  Date Added:

  August 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the Battery Management System control unit software does not correspond to current production specifications. As a result, the battery Malfunction Indicator Lamp (MIL) may illuminate when no system fault occurs. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the Battery Management System control unit software.

  Associated Products (7)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022209-0001.pdf↗
• August 29, 2025•Document ID: 11022204

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20250829

  Date Added:

  August 28, 2025

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the charging function does not correspond to the current series production configuration. The charging system software will be updated to stabilize the charging function of the vehicle. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

  Associated Products (14)

  2025 Mercedes-Benz C-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022204-0001.pdf↗
• August 28, 2025•Document ID: 11022203

  Service Bulletin/Repair Instructions
  SUSPENSION

  Mfr Comm. #:

  LI32.50-P-079670

  Date Added:

  August 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. Noises in recovery mode with the vehicle stationary 2. Noises when driving in a straight line on rough terrain 3. Noises when cornering and performing alternate steering movements 4. Non-assignable noises Cause Concern 1 - Noises in recovery mode with the vehicle stationary Concern 2 - Noises when driving in a straight line on rough terrain. These are normal operating noises of the hydraulic high-pressure pumps. Explanation: This is the "preview noise" which is heard when recovery mode is in operation, but which can also occur when driving over very uneven ground in the Comfort and Curve drive programs. This is a normal operating noise which is caused by the hydraulic high-pressure pumps (MPE). To compensate for the unevenness of the ground, large oil flows need to be generated and to do so, the MPEs turn at very high rotational speeds. Note: In the "ECO" drive program, the "Preview" function is deactivated so these noises should not occur when driving over uneven terrain; however the vehicle body will move noticeably. Concern 3 - Noises when cornering and performing alternate steering movements - reversing noise. Repeated rapid steering out of a curve generates a "grunting" noise. Explanation: This noise is caused by the MPEs when the pump's direction of rotation is reversed. Note: The reversing noise can occur in all drive programs, but is most clearly reproducible in the Curve drive program and in Curve level 3. Carry out an evaluation firstly in Curve levels 1 to 3 (at the highest Curve level 3, the noise will also be at its loudest!), and then in the Comfort drive program. Concern 4 - Non-assignable noises. Remedy Generally check whether the same noises also occur in ECO mode - in this mode the Preview/ROAD SURFACE SCAN function is deactivated and the high-pressure pumps run at reduced speed. Consequently, it is possible to differentiate between normal operating noises and unusual noises. Regarding 1, 2: Explain the high-pressure system, replacing the suspension struts or pumps is not useful, as these noises are caused by the high-pressure pump unit and should be regarded as normal operating noises. Regarding 3: This is currently a normal operating noise and represents the series production configuration; consequently replacing the components is not useful. Regarding 4: There will certainly be other unknown noises that we are not yet familiar with; therefore please report these as well. For these, create a TIPS case and include informative video recordings of the noises. The driving situation in the drive program in which the noises occur should be shown. For comparison, also attach a recording of this same driving situation in ECO mode. Additional attachments required: - Logs for control units N51/8, M67, M67/1, M67/2, M67/3. - Actual values for the pressures of the four hydraulic high-pressure pumps at standstill.

  Associated Products (9)

  2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLE-Class
  Associated Documents

  • DownloadMC-11022203-0001.pdf↗
• August 9, 2025•Document ID: 11021892

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI15.40-P-077947

  Date Added:

  August 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Combustion engine could no longer be started, only electric driving possible Cause High-voltage belt-driven starter-alternator defective Remedy Requirement: Before carrying out test work, it must be ensured that the person performing the work has successfully completed the required qualification for work on the high-voltage system. Note: In order to check whether the high-voltage belt-driven starter-alternator is defective, please carry out the test below. If the fault "P0E2F00 The electrical fuse B for the high voltage has a malfunction" is stored in the N82/10 BMS control unit, the HV protocol must be checked to see whether the fuse for the auxiliary consumers is defective. In this case, the high-voltage battery must be replaced after the short circuit has been eliminated. (See attachment) The defective high-voltage belt-driven starter-alternator must always be sent back via the existing return delivery process for analysis. Check: Please disconnect the high-voltage plug at the high-voltage belt-driven starter-alternator and connect test adapter 000 589 94 63 00. Measure resistance HV+ to HV-. If the final measurement result is between 0–1 ohm, the high-voltage belt-driven starter-alternator with the short circuit must be replaced. If either one of or both the fault codes P0C0B16 and P0C0B17 are saved in the high-voltage belt-driven starter-alternator control unit G2/3, please replace the high-voltage belt-driven starter-alternator, since no short circuit can be measured here and this therefore concerns a hardware defect. Please check the serial number on the silver adhesive label below the SW number on the front of the high-voltage belt-driven starter-alternator. Example: 2314300044 (the first 10 digits, see attachment) Important note: If the number is greater than 2329100027, a TIPS case must be created. In this instance, please attach the following documents to the TIPS case: • Quick test • High-voltage event log • Picture of the silver adhesive label on the front of the high-voltage belt-driven starter-alternator (serial number) • Attach the measurement results with pictures

  Associated Products (6)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11021892-0001.pdf↗
• August 5, 2025•Document ID: 11022056

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-079582

  Date Added:

  August 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Valeo Steering Column Module (N80) goes into bootloader after updating software to A2239028729. To verify the supplier and software number of the steering column module. See attachment "Supplier Identification" for assistance. Cause MRSM/SCCM flashed to SW A2239028729 Remedy Please send VIN specific ID1 Support Package online using the XENTRY Kit used during the time the error occurred. Then, create an XSS ticket using the Support Tool icon under XENTRY Diagnosis.

  Associated Products (18)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022056-0001.pdf↗