Mercedes-Benz GLA-Class Service Bulletins (2021)

274 manufacturer communications on file.

• September 26, 2026•Document ID: 11038188

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-080896

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

  Associated Products (91)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT+ 71 more
  Associated Documents

  • DownloadMC-11038188-0001.pdf↗
• September 22, 2026•Document ID: 11038186

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-078779

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038186-0001.pdf↗
• September 15, 2026•Document ID: 11038174

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-080383

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

  Associated Products (54)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class+ 34 more
  Associated Documents

  • DownloadMC-11038174-0001.pdf↗
• September 14, 2026•Document ID: 11038217

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038217-0001.pdf↗
• September 1, 2026•Document ID: 11037487

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  September 25, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: • Driving style such as two footed driving where the pad might be in constant contact with the rotor. • Brake pressure and application style (stop‑and‑go traffic with consistent light brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. • When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3‑4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re‑assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re‑apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

  Associated Products (155)

  2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT+ 135 more
  Associated Documents

  • DownloadMC-11037487-0001.pdf↗
• August 29, 2026•Document ID: 11037211

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI 27.10-P-080851

  Date Added:

  September 9, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Intermittent shift feel or thud/clunk noise perceived, such as a brief jerk or transmission reaction during certain driving situations. May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dual‑clutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: • The customer is coasting towards a red traffic light. • The traffic light turns green while the vehicle is still coasting. • The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dual‑clutch transmission

  Associated Products (49)

  2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz GLA-Class+ 29 more
  Associated Documents

  • DownloadMC-11037211-0001.pdf↗
• August 29, 2026•Document ID: 11037210

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI27.19-P-080869

  Date Added:

  September 9, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Temporary no start condition with check engine light and multiple warning messages. When performing a quick test, the following fault code is stored in Y3/14 ‑ Transmission control for 8‑speed dual‑clutch transmission (DKG): P24F100 The wake‑up line of the control unit has a short circuit to positive. Cause Possible signal timing between EZS control unit and Transmission Control Unit (DKG) Remedy As of 7/15/2026, new SCN coding is available for the EZS control unit. IPR will advise to open a TIPS case for EZS (N73), this is due to GLA models requiring support for SCN coding procedure. GLB (X247) and CLA (118) No TIPS case necessary. 1. SCN coding of EZS Control Unit 2. Clear all faults and perform extended road test with multiple drive cycles GLA (H247) Special function password required. 1. Verify if special procedure Central Locking ‑ Development Data is present in EZS (figure 1) 2. Submit a TIPS case to the Powertrain Inbox with the following information: ‑ Initial Quick Test w/ freeze frame data ‑ IPR Result ‑ DKG Control Unit Log ‑ EZS Control Unit Log ‑ Initial EEPROM data ‑ EZS special procedure menu If the vehicle has had this LI performed and P24F100 has returned, please submit a TIPS case to the Powertrain Inbox.

  Associated Products (20)

  2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz GLB-Class
  Associated Documents

  • DownloadMC-11037210-0001.pdf↗
• August 25, 2026•Document ID: 11036514

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-080823

  Date Added:

  August 31, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customers may report one or more of the following: • Transmission malfunction message • Check engine light illuminated • Shifts into N • Concern disappears after ignition cycle When performing a quick test, the following fault code is stored in Y3/14 ‑ Transmission control for 8‑speed dual‑clutch transmission (DKG): P056300 The on‑board power supply voltage is too high. Cause An overvoltage condition is detected exclusively within the transmission control unit, storing fault P056300 once the measured voltage exceeds 16V. Remedy This LI applies if the freeze frame data for P056300 show a supply voltage between 15.75 to 16.50 volts, and no other control units report overvoltage. (figure 1) Long Term Resolution: Software resolutions have been released. Check validity and ensure your Xentry is updated with latest Addons before continuing: 1. Perform software update for Y3/14 ‑ Transmission control for 8‑speed dualclutch transmission (DKG) available software listed in Parts 2. Clear fault memory and perform final test drive If the customer complaint matches this LI and the software currently installed on the vehicle is not listed, please submit a TIPS case to the Powertrain inbox with the following information: ‑ Initial Quick Test w/ Freeze Frame Data ‑ DKG Control Unit Log ‑ Latest EEPROM data ‑ Screenshot of software availability

  Associated Products (11)

  2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class
  Associated Documents

  • DownloadMC-11036514-0001.pdf↗
• August 24, 2026•Document ID: 11036511

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; STRUCTURE:BODY

  Mfr Comm. #:

  LI72.20-P-075746

  Date Added:

  August 31, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

  Associated Products (97)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class+ 77 more
  Associated Documents

  • DownloadMC-11036511-0001.pdf↗
• August 21, 2026•Document ID: 11036343

  Other
  POWER TRAIN

  Mfr Comm. #:

  PSL-NCU Return Parts 8/21

  Date Added:

  August 25, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, September 10th, 2026. After September 10th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

  Associated Products (6)

  2026 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLA-Class
  Associated Documents

  • DownloadMC-11036343-0001.pdf↗
• August 15, 2026•Document ID: 11036999

  Warranty Program/Extension
  FUEL/PROPULSION SYSTEM

  Mfr Comm. #:

  CL - Tank Leak Detection

  Date Added:

  September 4, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Dear Mercedes-Benz Owner: In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

  Associated Products (92)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class+ 72 more
  Associated Documents

  • DownloadMC-11036999-0001.pdf↗
• August 12, 2026•Document ID: 11036142

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  August 12, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (119)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 99 more
  Associated Documents

  • DownloadMC-11036142-0001.pdf↗
• August 6, 2026•Document ID: 11036101

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  August 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11036101-0001.pdf↗
• August 4, 2026•Document ID: 11035713

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-080823

  Date Added:

  August 5, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customers may report one or more of the following: • Transmission malfunction message • Check engine light illuminated • Shifts into N • Concern disappears after ignition cycle When performing a quick test, the following fault code is stored in Y3/14 - Transmission control for 8-speed dual-clutch transmission (DKG): P056300 The on-board power supply voltage is too high. Cause An overvoltage condition is detected exclusively within the transmission control unit, storing fault P056300 once the measured voltage exceeds 16V. Remedy This LI applies if the freeze frame data for P056300 show a supply voltage between 15.75 to 16.50 volts, and no other control units report overvoltage. (figure 1) Long Term Resolution: Software resolutions are being rolled out for various models. Check validity and ensure your Xentry is updated with latest Addons before continuing: 1. Perform software update for Y3/14 - Transmission control for 8-speed dual-clutch transmission (DKG) - available software listed in Parts 2. Clear fault memory and perform final test drive Short Term Resolution: Please clear faults and perform an extended test drive. The vehicle may be released to the customer until software is available. If the customer complaint matches this LI and the software currently installed on the vehicle is not listed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial Quick Test w/ Freeze Frame Data - DKG Control Unit Log - Latest EEPROM data - Screenshot of software availability

  Associated Products (11)

  2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class
  Associated Documents

  • DownloadMC-11035713-0001.pdf↗
• July 31, 2026•Document ID: 11035490

  Warranty Program/Extension
  FUEL/PROPULSION SYSTEM

  Mfr Comm. #:

  EW - DMTL

  Date Added:

  August 3, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  This NCU replaces the prior NCU issued on May 15, 2025, and contains additional MY 2023 and MY 2024 vehicles which are highlighted below. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: •Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).

  Associated Products (69)

  2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class+ 49 more
  Associated Documents

  • DownloadMC-11035490-0001.pdf↗
• July 24, 2026•Document ID: 11035217

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.21-P-080326

  Date Added:

  July 24, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

  Associated Products (47)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class+ 27 more
  Associated Documents

  • DownloadMC-11035217-0001.pdf↗
• July 17, 2026•Document ID: 11035120

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; STEERING

  Mfr Comm. #:

  LI46.10-P-078012

  Date Added:

  July 21, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Hand detection system – malfunction / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" "Active steering assist not available" Cause Possible causes: Hand detection mat, hand detection control unit, contacts, and electrical feed line. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Check: Please do not replace the HOSWD control unit. Please flash the new SW and perform the SCN coding for the HOSWD control unit (N179/1) (available from July 2026). The software can be flashed onto all HOSWD213 with HW number A0009011522 and all HOSWD223 with HW number A0009011422. Please also flash the SW for the IDC control unit (N62/4), if possible (only applies to HOSWD223). Erase fault memory Remedy: Turn on the ignition or start the engine without touching the steering wheel. If, after 10 seconds without touching the steering wheel, one of the three fault messages appears on the instrument cluster: Check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, crimp connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage -> replace the steering wheel rim. If a yellow message does not appear on the instrument cluster within 10 seconds: Grasp the steering wheel fully with both hands, including the chrome molding at the 6 o'clock position (see picture 1). If the fault is triggered by grasping the steering wheel rim or pressing the clip at the 6 o'clock position, check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, kinked connections, loose connections, etc. (example in picture 2 and 3). Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage: Replace the steering wheel rim. Please do not replace the HOSWD control unit. A TIPS case should be created if fault profile is unclear. In the event of a customer complaint and a further fault code in HOSWD: B1E7713: Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). B1F1F04: Check the control unit of the hand detection system; if necessary, replace this with the control unit from a donor vehicle (make sure that the hardware part numbers are identical).

  Associated Products (19)

  2021 Mercedes-Benz A-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2021 Mercedes-Benz S-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz AMG GT2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz CLS-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz GLA-Class2020 Mercedes-Benz GLB-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class
  Associated Documents

  • DownloadMC-11035120-0001.pdf↗
• July 14, 2026•Document ID: 11035005

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  July 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11035005-0001.pdf↗
• July 8, 2026•Document ID: 11034888

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-080383

  Date Added:

  July 8, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

  Associated Products (47)

  2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class+ 27 more
  Associated Documents

  • DownloadMC-11034888-0001.pdf↗
• July 2, 2026•Document ID: 11034506

  Service Bulletin/Repair Instructions
  ENGINE; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.21-P-080326

  Date Added:

  July 6, 2026

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

  Associated Products (40)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLA-Class+ 20 more
  Associated Documents

  • DownloadMC-11034506-0001.pdf↗