Mazda Mazda3 Service Bulletins (2022)
429 manufacturer communications on file.
- July 8, 2026•Document ID: 11035595Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STEERING
- Mfr Comm. #:
- 06-001-26
- Date Added:
- August 4, 2026
- Manufacturer:
- MAZDA
SummaryDESCRIPTION Some customers may complain that the electric power steering warning light illuminates after engine start and DTC U2011:1C is stored. Zinc-plated whisker may form inside the EPS motor and trigger the DTC. However, since it is cleared when power is supplied during DTC detection, normal operation can be restored by turning the ignition OFF and then ON. Furthermore, there is no possibility of recurrence. This case may be resolved through a simple inspection or repair without the need for parts replacement, potentially avoiding unnecessary customer waiting time.
Associated Products (12)Associated Documents - July 2, 2026•Document ID: 11035606Service Bulletin/Repair InstructionsVISIBILITY/WIPER
- Mfr Comm. #:
- SA-043-26
- Date Added:
- August 4, 2026
- Manufacturer:
- MAZDA
SummaryThis SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-063/24 09/06/24 DESCRIPTION The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction.
Associated Products (16)Associated Documents - July 2, 2026•Document ID: 11035597Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 09-016-26a
- Date Added:
- August 4, 2026
- Manufacturer:
- MAZDA
SummaryThis bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-016/26 05/06/26 DESCRIPTION Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify the customer concern. 2. Remove the front seat cushion trim and the front seat back trim for both the driver and passenger seats according to the instructions in MGSS.
Associated Products (6)Associated Documents - July 1, 2026•Document ID: 11034448Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; ELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- SA-042-26
- Date Added:
- July 3, 2026
- Manufacturer:
- MAZDA
SummaryThis Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out
Associated Products (35)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 15 moreAssociated Documents - June 19, 2026•Document ID: 11034447Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-041-26
- Date Added:
- July 3, 2026
- Manufacturer:
- MAZDA
SummaryThis SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
Associated Products (41)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 21 moreAssociated Documents - June 17, 2026•Document ID: 11034439Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-027-26a
- Date Added:
- July 3, 2026
- Manufacturer:
- MAZDA
SummaryThis SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.
Associated Products (40)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 20 moreAssociated Documents - June 16, 2026•Document ID: 11034845Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-0-38/26
- Date Added:
- July 8, 2026
- Manufacturer:
- MAZDA
SummaryDESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
Associated Products (35)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 15 moreAssociated Documents - June 16, 2026•Document ID: 11034444Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-040-26
- Date Added:
- July 3, 2026
- Manufacturer:
- MAZDA
SummaryThis Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-009/25 08/22/25 and 02/18/25 DESCRIPTION Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs. Index System Outline • MYMAZDA App Connected Vehicle (CV) Error Codes • Vehicle Confirmation Instructions • Troubleshooting Instructions • Resources
Associated Products (35)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 15 moreAssociated Documents - June 16, 2026•Document ID: 11034443Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; UNKNOWN OR OTHER
- Mfr Comm. #:
- SA-039-26
- Date Added:
- July 3, 2026
- Manufacturer:
- MAZDA
SummaryThis Service Alert supersedes the previously issued SA listed below. The changes are noted in Red text. SA-012/25 10/06/25, 08/21/25, 05/15/25 and 02/27/25 DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE NOTE: Before proceeding: Document the vehicle's current MAZDA CONNECT CMU software version. • 2019-2022 Models - Go to TSB 16-003/23 and confirm the CMU Serial Number is not within the affected range. • Document customer device Brand/Model/Model Number/software version on the repair order. • Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS -> Infotainment -> MAZDA CONNECT Updates ○ • If possible, complete the Microsoft Forms Questionnaire. Go to MGSS -> Infotainment -> MAZDA CONNECT Questionnaire.
Associated Products (35)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 15 moreAssociated Documents - May 19, 2026•Document ID: 11033447Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-034-26
- Date Added:
- June 4, 2026
- Manufacturer:
- MAZDA
SummaryThis service alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-047/25 10/07/25 DESCRIPTION When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. • If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs. • If the Telematics Control Unit (TCU) replacement is necessary, check "Vehicle Communication Line Status Reference" status detail first. The TCU can only be replaced under the following "Status Detail" conditions: Open Completed (OK) ○ Closed Completed (OK) ○ ○ If the TCU is replaced under the following "Status Detail" conditions, the customer may not be able to enroll into the replacement TCU. Processing (NG) ○ Request Failed (NG) ○ Open Failed (NG) ○ Flag Setting Failed TCU Activation 1. Install the new TCU.
Associated Products (34)2026 Mazda CX-302026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-30+ 14 moreAssociated Documents - May 7, 2026•Document ID: 11033115Service Bulletin/Repair InstructionsSEATS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 09-016-26
- Date Added:
- June 2, 2026
- Manufacturer:
- MAZDA
SummaryDESCRIPTION Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) REPAIR PROCEDURE 1. Verify the customer concern. 2. Remove the front seat cushion trim and the front seat back trim for both the driver and passenger seats according to the instructions in MGSS.
Associated Products (6)Associated Documents - May 2, 2026•Document ID: 11033445Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- SA-032-26
- Date Added:
- June 4, 2026
- Manufacturer:
- MAZDA
SummaryThis SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-011/25 10/16/25 and 02/27/25 DESCRIPTION Some customers will report that their fuel door (AKA, fuel filler door, fuel lid, and fuel-filler lid) was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present. REPAIR PROCEDURE 1. Check for pry marks around the door opening. Are there any pry marks? YES: This is due to outside influence and is not covered by Mazda warranty. NO: Continue to the next step. 2. Check the fuel door lock operation. a. Lock the doors and verify if the fuel door lock is locking. NOTE: The default setting is a 90-second delay after the doors lock, but the customer can set that to 0, 30, 60, 90, or 120 seconds. b. Unlock the doors and verify if the fuel door lock is unlocking. NOTE: There is no delay to this function, but the fuel door must be locked to confirm it is unlocking. See the lock note above. Is the fuel door lock operation working correctly? YES: The fuel door repair IS NOT covered by Mazda warranty. The fuel door lock is OK and the door was damaged because the vehicle was not unlocked. NO: The fuel door repair IS covered by Mazda warranty. The fuel door lock is NOT OK and damage to the door was done in order to access the lock. NOTE: If the door was already broken when it arrived at the dealership, Mazda will pay for the fuel door repair under warranty if the vehicle does NOT have an emergency release. Mazda will NOT pay for the fuel door under warranty if it has an emergency release.
Associated Products (22)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32025 Mazda CX-302025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32024 Mazda CX-302024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32023 Mazda CX-302023 Mazda CX-502023 Mazda Mazda32022 Mazda CX-302022 Mazda Mazda3+ 2 moreAssociated Documents - April 30, 2026•Document ID: 11032104Service Bulletin/Repair InstructionsSTRUCTURE:BODY; UNKNOWN OR OTHER
- Mfr Comm. #:
- SA-031-26
- Date Added:
- May 5, 2026
- Manufacturer:
- MAZDA
SummaryDESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
Associated Products (40)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 20 moreAssociated Documents - April 29, 2026•Document ID: 11032106Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD5 Parts Warr b
- Date Added:
- May 5, 2026
- Manufacturer:
- MAZDA
SummaryValve Stem Seals Class Action Settlement Program for Excessive Oil Consumption and Oil Consumption Powertrain Warranty Extension Special Service Program SSPD5. Updated April 28, 2026 – Related oil part number for warranty claims is now 0000-77-5W30-QT (engine oil) as the 5555 warranty part number has been removed. As a reminder, all coverage reverts back to the original extension of 7 years or 84,000 miles whichever comes first. WARRANTY EXTENSION If you have any questions regarding this campaign, please read the Mazda Dealer FAQ’s available in MGSS under this campaign before contacting Dealer Recall Help. Effective October 25,2025: In the final settlement agreement, which was approved by the Court in October 2024, there is also coverage for Valve Stem Seal related repairs for an additional 1 year and 12,000 miles however, this coverage only applies if the vehicle is presented to a Mazda dealer by October 15, 2025 and has no more than 96,000 miles. This additional 1-year coverage has expired. As of October 25, 2025 all coverage under SSPD5 has reverted to the original extension limit of 7 years, 84,000 miles including the Powertrain Limited Warranty Extension is of 7 years, 84,000 miles. Update August 2025: The Court has clarified that under the settlement agreement, the Mazda Powertrain Limited Warranty Extension includes coverage for 7 years or 84,000 miles, whichever comes first, for all powertrain components in the Warranty Booklet under the Powertrain Limited Warranty Parts List (i.e. without restriction to engine issues, oil consumption or valve stem seal issues). Reimbursement will also be provided for any Class Member who was denied coverage and paid out-of-pocket for a qualifying Powertrain Limited Warranty repair during the applicable period.
Associated Products (7)Associated Documents - April 21, 2026•Document ID: 11032103Service Bulletin/Repair InstructionsSERVICE BRAKES; UNKNOWN OR OTHER; ENGINE; POWER TRAIN
- Mfr Comm. #:
- SA-029-26
- Date Added:
- May 5, 2026
- Manufacturer:
- MAZDA
SummaryThis Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
Associated Products (40)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 20 moreAssociated Documents - April 16, 2026•Document ID: 11032101Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SA-026-26
- Date Added:
- May 5, 2026
- Manufacturer:
- MAZDA
SummaryThis Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
Associated Products (39)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 19 moreAssociated Documents - April 15, 2026•Document ID: 11032102Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-027-26
- Date Added:
- May 5, 2026
- Manufacturer:
- MAZDA
SummaryThis SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.
Associated Products (40)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 20 moreAssociated Documents - March 31, 2026•Document ID: 11030603Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STRUCTURE:BODY
- Mfr Comm. #:
- 09-013-26
- Date Added:
- April 2, 2026
- Manufacturer:
- MAZDA
SummaryDESCRIPTION Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. Door outer handle touch sensor for locking (1) / unlocking (2) NOTE: If the concern occurs after specific operation as described below, refer to the TSB 09-046/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND UNLOCK AFTER A SPECIFIC OPERATION). 1. [MX-30] After using cabin preconditioning or hazard warning lights for approx.15 minutes. 2. [MAZDA3 and CX-30] After using hazard warning lights for approx. 15 minutes. 3. [MAZDA3, CX-30 and MX-30] When both touch sensors are touched at once. Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify customer concern. 2. Repair the vehicle depending on the experienced symptom(s). Symptom 1: Follow the "Procedure to waterproof a touch sensor” below to make the touch sensor waterproof. Symptom 2: Replace the front outer handle with a modified one according to the instructions on MGSS. Mazda3 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) CX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) MX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) If both symptoms are experienced: Replace the front outer handle with a modified one and follow the “Procedure to waterproof a touch sensor” below to make the touch sensor waterproof. NOTE: DO NOT repair the other front outer handle for the vehicle if it is not experiencing any problems. 3. Verify the repair by checking if the new outer handle locks/unlocks the door correctly.
Associated Products (9)Associated Documents - March 11, 2026•Document ID: 11030636Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SA-014-26
- Date Added:
- April 2, 2026
- Manufacturer:
- MAZDA
SummaryThis Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.
Associated Products (36)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-302023 Mazda CX-5+ 16 moreAssociated Documents - March 5, 2026•Document ID: 11030701Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8 Repair d
- Date Added:
- April 4, 2026
- Manufacturer:
- MAZDA
SummarySubject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.
Associated Products (13)Associated Documents