Ford F-150 Service Bulletins (2021)
648 manufacturer communications on file.
- January 20, 2021•Document ID: 10186620Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SSM 49477
- Date Added:
- February 4, 2021
- Manufacturer:
- LINCOLN
SummarySome 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
Associated Products (34)2021 Ford Edge2021 Ford F-1502021 Lincoln Nautilus2020 Ford Edge2020 Ford F-1502020 Lincoln Continental2020 Lincoln MKX2020 Lincoln MKZ2020 Lincoln Nautilus2019 Ford Edge2019 Ford F-1502019 Ford Fusion2019 Lincoln Continental2019 Lincoln MKX2019 Lincoln MKZ2019 Lincoln Nautilus2018 Ford Edge2018 Ford F-1502018 Ford Fusion2018 Lincoln Continental+ 14 moreAssociated Documents - January 18, 2021•Document ID: 10186602Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SSM 49457
- Date Added:
- February 4, 2021
- Manufacturer:
- LINCOLN
SummarySome 2021 Mustang Mach-E/F-150/Edge/Nautilus vehicles may require a reboot of the SYNC 4 system. For vehicles equipped with a volume/power and seek buttons, press and hold both the volume/power and seek buttons for 10 seconds and the system will reboot. For vehicles not equipped with a volume/power button, holding the seek right and volume down buttons on the steering wheel controls will reboot the SYNC 4 system. The Workshop Manual (WSM) is in the process of being updated with this procedure.
Associated Products (5)Associated Documents - January 14, 2021•Document ID: 10186598Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 49446
- Date Added:
- February 4, 2021
- Manufacturer:
- FORD
SummarySome 2021 F-Super Duty vehicles equipped with a 6.2L or 7.3L engine, F-150 vehicles equipped with a 3.3L or 5.0L engine, and Explorer/Police Interceptor Utility vehicles equipped with a 3.3L engine may exhibit an illuminated malfunction indicator (MIL) with diagnostic trouble code (DTC) P0106 stored in the powertrain control module (PCM) while in transport mode, especially in higher altitudes. To correct the condition, clear the DTCs and deactivate transport mode. Refer to Workshop Manual (WSM), Section 419-10 > General Procedures. Before starting the engine in the procedure, cycle the ignition to OFF, cycle the ignition to ON, wait ten seconds, cycle the ignition to OFF, wait ten seconds, then start the engine. If the condition remains, refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for diagnostics.
Associated Products (6)Associated Documents - December 22, 2020•Document ID: 10184783Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT; EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER
- Mfr Comm. #:
- SSM 49419
- Date Added:
- January 4, 2021
- Manufacturer:
- FORD
SummarySome 2021 F-150 vehicles equipped with a 2.7L engine and built on or before 09-Dec-2020 may experience lack of heat from the HVAC system. This condition may be the result of a heater hose near the oil cooler being misrouted and/or twisted causing a restriction to coolant flow. To correct this condition, inspect the hose for damage and reroute the hose above the coolant hose running perpendicular then fill and bleed the cooling system following procedures in WSM section 303-03A. For claiming, use causal part 18472 and M-time.
Associated Products (1)Associated Documents - December 9, 2020•Document ID: 10184631Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- SSM 49388
- Date Added:
- January 5, 2021
- Manufacturer:
- FORD
Summary2021 F-150/Explorer/Aviator/Police Interceptor Utility vehicles without a diesel engine and/or without a 10R80 MHT transmission have a new PCM-Transmission Accelerated Main Control Break In routine added to the Diagnosis and Testing Section of the WSM. This new routine uses the Ford diagnostic scan tool to cycle the shift solenoids and clutch control valves to free them from contamination that may be sticking the valves. Refer to WSM, Section 307-01.
Associated Products (3)Associated Documents - December 4, 2020•Document ID: 10184629Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 49380
- Date Added:
- January 5, 2021
- Manufacturer:
- FORD
SummarySome 2021 F-150/Explorer/Aviator/Police Interceptor vehicles may exhibit a flashing powertrain malfunction (wrench) indicator while in transport mode with diagnostic trouble code (DTC) P112A stored in the powertrain control module (PCM). This may be due to excessive engine starts while the vehicle is in transport mode. To correct the condition, deactivate transport mode. Refer to Workshop Manual (WSM), Section 419-10 > General Procedures. Cycle the ignition to RUN. If the concern still exists, perform normal diagnostics in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual.
Associated Products (3)Associated Documents - December 4, 2020•Document ID: 10184628Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 49379
- Date Added:
- January 5, 2021
- Manufacturer:
- FORD
SummaryBefore attempting repairs for SYNC 4 system, Telematics Control Unit (TCU) or Gateway Module (GWM) concerns, dealers must complete workshop manual (WSM) diagnostics in section 415-00 for SYNC 4 or TCU concerns and 418-00 for GWM concerns. Do not attempt APIM, TCU or GWM reprogramming or replacement unless directed by a WSM pinpoint test. If the root cause of a concern is isolated to the APIM, TCU or GWM with all other possible causes ruled out, dealers must contact the Technical Assistance Center prior to performing repairs.
Associated Products (1)Associated Documents - September 2, 2020•Document ID: 10180615Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- HSB2020-09.02
- Date Added:
- October 2, 2020
- Manufacturer:
- FORD
SummarySales Bulletin - 2021 F-Series order guide released, Grove City Hotel break in notice, Cares Act notice, Ambulance Crash Testing link, HEPA filter availability update, Ohio Temporary tag notice, Dealer portal training material notice, Chassis/Vehicle availability notice
Associated Products (5)Associated Documents