BMW ActiveHybrid 3 Service Bulletins
601 manufacturer communications on file.
- June 1, 2014•Document ID: 10148099Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEAT BELTS
- Mfr Comm. #:
- 651214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryAirbag Warning Lamp Illuminated. An Airbag Warning lamp is illuminated and one or both of the following fault codes are stored in the Advanced Crash Safety Module (ACSM): 93099A- Safety battery terminal 2: Resistance too high 93099B - Safety battery terminal 2: Line connected incorrectly These two faults can also be accompanied by one or more of the following fault codes in the ACSM. The faults below are the result of one or both of the faults above, and will be resolved after performing the following repair. 930997- Safety battery terminal 2: short circuit to minus 930929- Driver's seat belt tensioner: Line connected incorrectly 930953- Knee airbag, front passenger Line connected incorrectly 93093B- Seatbelt tensioner Passenger: Line connected incorrectly 93091D- Front passenger airbag, stage 2: Line connected incorrectly 930911- Airbag, driver, valve: Line connected incorrectly CAUSE Inaccurate resistance measurement of the BST 2 by the ACSM control module
Associated Products (3)Associated Documents - June 1, 2014•Document ID: 10148097Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 510614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Repair Corrosion Protection Engine Compartment. Various engine compartment battery cable mounting points are not sufficiently protected against corrosion. Lack of corrosion protection can lead to improper connections associated with the battery cables. AFFECTED VEHICLES This Service Action involves F30 3 Series vehicles produced from June 2012 to January 2013. First check if a Service Action label with a code number 670 is already attached to the B-pillar. If a code number 670 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
Associated Products (11)Associated Documents - June 1, 2014•Document ID: 10148096Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- 360314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRDC: Incorrect Tire Position Displayed with Air Pressure Drop. When there is a low tire pressure warning, in some cases the position of the affected tire may be incorrectly displayed in the instrument cluster and CD (Control Display). Software error in the RDC (tire pressure control) module in conjunction with wheel electronics part number 4 078 787 or 4 079 152.
Associated Products (24)Associated Documents - June 1, 2014•Document ID: 10056099Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; COMMUNICATION
- Mfr Comm. #:
- SIB-84-03-14
- Date Added:
- September 3, 2014
- Manufacturer:
- BMW
SummaryBMW: WHEN USING IPHONE, VARIOUS CONNECTIVITY FAILURES OCCUR, SUCH AS DISCONNECTION OF CALL, LIST OF CONTACTS INCOMPLETE, DUE TO THE VARIANTS AND SOFTWARE USED. MODEL 2008-2014.
Associated Products (30)Associated Documents - June 1, 2014•Document ID: 10056097Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; AIR BAGS
- Mfr Comm. #:
- SIB-65-12-14
- Date Added:
- September 3, 2014
- Manufacturer:
- BMW
SummaryBMW: AIR BAG WARNING LIGHT ILLUMINATES DUE TO RESISTANCE MEASUREMENT BEING INACCURATE OF BST2 BY ACSM CONTROL MODULE. MODEL 2014 F30H (ACTIVEHYBRID3). *PE
Associated Products (1)Associated Documents - May 1, 2014•Document ID: 10148334Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 630814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryActive Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. Fault Code 8041B6 is present. Broken mounting bolt holding on the rear height sensor bracket.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148333Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
Associated Products (79)Associated Documents - May 1, 2014•Document ID: 10148323Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK; STRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- 511314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTrunk Lid Does Not Open Completely. The customer may complain that the trunk does not open fully when using the remote key or hands-free trunk-lid opening (a Comfort Access function). CAUSE * A dry trunk lid seal causes the trunk lid to stick. * F30 and F32 only: A trunk return spring that is not installed correctly may not open the trunk lid fully.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148321Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMF56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand. In a continuing effort to maintain the utmost in Motorer satisfaction, MINI USA is offering our dealer partners an alternative solution, the "Make Good" program. For all affected MINI F56 vehicles: * Produced from May 1, 2014 to June 30, 2014 and * Built without the factory order "Contrasting Roof and Mirror Caps" option (382 and 383) Your MINI dealer can offer these Motorers the installation of an accessory roof graphic or set of mirror caps. The Motorer has the choice of either the accessory roof graphic or exterior mirror caps, not both. MINI Area Manager (AM) "Field Authorization" (FAS) is not required. Note: For eligible vehicles (VINs) that are affected by this production restriction, the procedure outlined in this bulletin only applies to mirror caps or roof graphics installed by your dealer. Mirror caps or roof graphics installed through the MINI USA "VIA" (VDC-Installed Accessory) program are not eligible for reimbursement through this Make Good Program.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148316Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
- Mfr Comm. #:
- 340313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
Associated Products (53)Associated Documents - May 1, 2014•Document ID: 10148315Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
- Mfr Comm. #:
- 340213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
Associated Products (57)Associated Documents - May 1, 2014•Document ID: 10148313Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; STEERING
- Mfr Comm. #:
- 320114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Power Steering Pump Belt Pulley. The screw connection on the power steering pump belt pulley may slacken. This may lead to an audible squeaking and rattling at the pulley drive. AFFECTED VEHICLES This Service Action involves 5 Series 535d vehicles according to VIN selection. First check if a Service Action label with a code number 682 is already attached to the B-pillar. If a code number 682 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
Associated Products (22)Associated Documents - May 1, 2014•Document ID: 10148312Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE; SUSPENSION:FRONT:WHEEL BEARING
- Mfr Comm. #:
- 310112
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (70)Associated Documents - May 1, 2014•Document ID: 10148310Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 170114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryLow Coolant Level with No Sign of External Leaks. The Low Coolant Warning light is on and there are no signs of a visual leak. Pressure testing the cooling system may or may not show an internal leak (loss of pressure). There may also be a complaint of transmission fluid leaking from the vent on top of the transmission; poor shift quality; or a shuddering from the transmission. There is an internal failure of the automatic transmission oil cooler, allowing coolant to mix with transmission fluid. Possible faulty coolers were built between 6/6/2013 and 8/4/2013.
Associated Products (11)Associated Documents - May 1, 2014•Document ID: 10148308Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (82)Associated Documents - April 1, 2014•Document ID: 10148276Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 650514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTraffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
Associated Products (209)Associated Documents - April 1, 2014•Document ID: 10148273Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (242)Associated Documents - April 1, 2014•Document ID: 10148270Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY:DOOR
- Mfr Comm. #:
- 511014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Door Loudspeaker Make Noises When Cold. The customer complains of front door loudspeaker noises when the temperature is below freezing. CAUSE Water from the door window may enter the rear area of the front door medium range loudspeaker basket/cage and can solidify when the temperature drops below freezing, creating the noise.
Associated Products (24)Associated Documents - April 1, 2014•Document ID: 10148269Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES
- Mfr Comm. #:
- 510914
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Repair Corrosion Protection in Engine Compartment. Various engine compartment battery cable mounting points are not sufficiently protected against corrosion. Lack of corrosion protection can lead to improper battery cable connections.
Associated Products (9)Associated Documents - April 1, 2014•Document ID: 10148268Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES; ELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- 510814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Repair Corrosion Protection in Engine Compartment. Various engine compartment battery cable mounting points are not sufficiently protected against corrosion. Lack of corrosion protection can lead to improper battery cable connections.
Associated Products (6)Associated Documents