BMW 750i Service Bulletins
634 manufacturer communications on file.
- June 1, 2013•Document ID: 10150076Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- 620613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (70)Associated Documents - June 1, 2013•Document ID: 10150070Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummarySqueaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
Associated Products (40)Associated Documents - June 1, 2013•Document ID: 10150069Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 270213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryKnocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
Associated Products (40)Associated Documents - June 1, 2013•Document ID: 10150067Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 121413
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryPERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a recall campaign is announced by BMW NA, centers must ensure that all recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. SUBJECT Voluntary Emissions Recall Campaign 13E-A01: Program Control Units (Tank Ventilation). Due an error in the DME (Digital Motor Electronics) software, the fuel tank ventilation system may not sufficiently purge the active carbon canister of accumulated fuel vapor under certain engine operating conditions. As a result, this may lead to a fuel smell around the vehicle, especially in areas with high ambient temperatures. In order to remedy the s
Associated Products (8)Associated Documents - May 1, 2013•Document ID: 10149618Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 840613
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION Part Number
Associated Products (72)Associated Documents - May 1, 2013•Document ID: 10149617Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryTCB: Emergency Call Is Erroneously Triggered. An emergency call is erroneously made with no input from the driver. The following fault codes are stored in the TCB: * 0xB7F325 - Emergency call loud speaker: break in circuit * 0xB7F319 - Emergency call button: short circuit * 0xB7F326 - Emergency call loud speaker: short circuit to earth * 0xB7F33E - Automatic emergency call triggered frequently CAUSE TCB control unit error
Associated Products (51)Associated Documents - May 1, 2013•Document ID: 10149610Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640413
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryRattling/Grinding Noises from Center Console. When the heating and air conditioning system is first turned on, a grinding noise may be heard from the right side of the front center console. CAUSE The bushing of the blending flap for the rear seat outlet lacks sufficient grease.
Associated Products (49)2014 BMW 528i2014 BMW 535d2014 BMW 535i2014 BMW 550i2014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72014 BMW M52013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW ActiveHybrid 7+ 29 moreAssociated Documents - May 1, 2013•Document ID: 10149608Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 613812
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (61)Associated Documents - May 1, 2013•Document ID: 10149597Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 340612
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV
Associated Products (44)Associated Documents - May 1, 2013•Document ID: 10149596Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340213
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model
Associated Products (59)Associated Documents - May 1, 2013•Document ID: 10149593Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 270212
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV"
Associated Products (39)Associated Documents - May 1, 2013•Document ID: 10149590Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (69)Associated Documents - May 1, 2013•Document ID: 10149589Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- 130409
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
Associated Products (120)Associated Documents - May 1, 2013•Document ID: 10149581Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 120513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryService Engine Soon Light Flashes with Throttle Adaptation Faults Stored. The EML light flashes with a check control message for reduced power output and/or the Service Engine Soon lamp (MIL) flashes. During the throttle valve adaptation (teach-in limit run), faults may occur due to signal voltage oscillations. This could lead to a termination of the teach-in routine or an incorrect value taught in at the lower limit. The following faults can be stored in the DME memory: E82, E84, E88, E89, E92, and E93 BN2000 vehicles * 28D0: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 28D4: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 28C4: throttle valve, adaptation: Emergency air position not adapted * 28A0: throttle valve angle - Intake manifold absolute comparison: pressure too high ??3166: Tank-ventilation system: fault F01, F02, F06, F07, F10, F12, F13, F30, F31, and ALPINA B7 BN2020 vehicles: * 101408: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 107AE0: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 101402: throttle valve, adaptation: Emergency air position not adapted * 101F01: throttle valve angle - Intake manifold absolute comparison: pressure too high ??190F08: Tank-ventilation system: fault Sensitivity of the throttle valve sensor (only affects parts installed during this production period)
Associated Products (38)Associated Documents - May 1, 2013•Document ID: 10149577Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 110113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"N63 and N63T Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity. Customers with one of the vehicles above may complain that the engine's oil consumption is ""too high,"" resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being ""due."" When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to ""add 1 quart of engine oil."" After topping up and continued operation, the ""add engine oil"" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a ""turbocharged"" engine could require topping up of the engine oil more frequently."
Associated Products (26)Associated Documents - April 1, 2013•Document ID: 10149491Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Hardware error in the Headunit-High"
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149488Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 640113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMRed or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149346Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"High Battery Discharge Warning: Battery Needs Replacement. After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: * Unfavorable driving profile - excessive short trips * Excessive terminal 30B after run - normal coolant pump or electric fan operation * Extremely cold temperatures * Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups"
Associated Products (15)Associated Documents - April 1, 2013•Document ID: 10149342Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 340513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHill Descent Control Inoperative After Programming with ISTA/P 2.49.0 or 2.49.1. Hill Descent Control is inoperative after programming the vehicle with ISTA/P versions 2.49.0. or 2.49.1. Central Gateway Module software error.
Associated Products (34)Associated Documents - April 1, 2013•Document ID: 10149335Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
Associated Products (69)Associated Documents