BMW 528i Service Bulletins
504 manufacturer communications on file.
- November 1, 2014•Document ID: 10148427Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM:WIRING
- Mfr Comm. #:
- 651614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCentral Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID Affected Central Information Displays were manufactured from 02/01/2013 to 06/09/2014. The manufacturing date is included in the serial number printed on the parts label on the CID. IMPORTANT: The manufacturing date is written in the following way: dd mm yy Example: The manufacturing date of August 15, 2013 is printed on the label in the following way: 15 08 13
Associated Products (45)Associated Documents - November 1, 2014•Document ID: 10148423Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (138)Associated Documents - November 1, 2014•Document ID: 10148421Service Bulletin/Repair InstructionsSTRUCTURE:BODY; EQUIPMENT:OTHER:LABELS
- Mfr Comm. #:
- 513314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
Associated Products (80)Associated Documents - October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149381Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660814
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummarySide View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
Associated Products (101)Associated Documents - October 1, 2014•Document ID: 10149379Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
Associated Products (53)Associated Documents - October 1, 2014•Document ID: 10149378Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 631114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryLED Low Beam Flashes Briefly After Ignition Switched ON. 1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)
Associated Products (78)Associated Documents - October 1, 2014•Document ID: 10149377Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 631014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryAdaptive Headlight Malfunction. A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.
Associated Products (46)Associated Documents - October 1, 2014•Document ID: 10149366Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 320414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryEngine: Fault Code 4823FC. Page 1 of 2 October 2014 Technical Service When starting the engine, the yellow EPS warning lamp may briefly light up. The power assist may also be reduced during this process. A brief undervoltage occurs in the EPS when starting the engine. The EPS recognizes this brief undervoltage and stores a fault code.
Associated Products (17)Associated Documents - October 1, 2014•Document ID: 10149355Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
Associated Products (58)Associated Documents - October 1, 2014•Document ID: 10149287Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121412
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummarySI B12 14 12 October 2014 Engine Electrical Systems Technical Service This Service Information bulletin supersedes SI B12 14 12 dated February 2014. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine loses power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored: E70, E71, E82, E88, E90, E91, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies may have faulty assembly bolts. One or more of the four assembly bolts have loosened or broke
Associated Products (31)Associated Documents - October 1, 2014•Document ID: 10149285Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
- Mfr Comm. #:
- 112014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDelivery Stop: Crankcase Failure. A Delivery Stop has been issued on certain 2015 model year vehicles with N20/N26 engines produced from September 4, 2014 through October 21, 2014. These vehicles may have a crankcase failure. Approximately 145 vehicles are affected.
Associated Products (27)Associated Documents - October 1, 2014•Document ID: 10149282Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 111414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryEngine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
Associated Products (93)Associated Documents - October 1, 2014•Document ID: 10149279Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 070314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - October 1, 2014•Document ID: 10149278Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 011314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryBMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.
Associated Products (36)Associated Documents - October 1, 2014•Document ID: 10149277Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE
- Mfr Comm. #:
- 011014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryEngine Camshaft (VANOS) Adjustment Units: Limited Warranty Extension to 10 Years Without Mileage Limitation. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the Camshaft (VANOS) Adjustment Units on certain model BMW vehicles equipped with the non-turbocharged 6-cylinder engine to: 10 years without mileage limitation, as determined by the vehicle's original in-service date. This "component-specific" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable New Vehicle/SAV Limited Warranty's exclusions and limitations, in addition to the vehicle and coverage eligibility requirements. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem.
Associated Products (21)Associated Documents - October 1, 2014•Document ID: 10057762Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH
- Mfr Comm. #:
- SI B65 13 13
- Date Added:
- June 24, 2015
- Manufacturer:
- BMW
SummaryBMW: SOME BMW MODELS CENTRAL INFORMATION DISPLAY (CID) ARE BLANK AND DISPLAY "NO SIGNAL". *TA
Associated Products (7)Associated Documents - October 1, 2014•Document ID: 10057568Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH
- Mfr Comm. #:
- SIB-63-11-14
- Date Added:
- June 10, 2015
- Manufacturer:
- BMW
SummaryBMW: ON SOME VEHICLES, WHEN STARTING, LOW BEAM, WITH 0552 OPTION, WOULD BRIEFLY FLASHES, DUE TO A FAULTY LED MAIN LIGHT MODULE THAT NEEDS REPLACING. MODEL 2008-14 F01, F02, F06, F07, F10, F12, F13, F25. *PE
Associated Products (95)Associated Documents - October 1, 2014•Document ID: 10057567Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- SIB-63-10-14
- Date Added:
- June 10, 2015
- Manufacturer:
- BMW
SummaryBMW: SOME VEHICLES EXPERIENCING VARIOUS MESSAGE DISPLAYED REGARDING MALFUNCTION OF LED HEADLIGHT, WITH OPTIONS 0552 AND 0524. *PE
Associated Products (19)Associated Documents - September 1, 2014•Document ID: 10148039Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"
Associated Products (40)Associated Documents