BMW 528i Service Bulletins
504 manufacturer communications on file.
- May 1, 2015•Document ID: 10147131Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryService Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
Associated Products (89)Associated Documents - May 1, 2015•Document ID: 10147130Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (74)Associated Documents - May 1, 2015•Document ID: 10147127Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (56)Associated Documents - May 1, 2015•Document ID: 10147125Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Associated Products (91)Associated Documents - May 1, 2015•Document ID: 10147123Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - April 6, 2015•Document ID: 10193495Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- B510415
- Date Added:
- May 17, 2021
- Manufacturer:
- BMW
SummaryThe customer complains of rattling noises from the rear window when driving on rough roads.
Associated Products (50)Associated Documents - April 1, 2015•Document ID: 10152317Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- B660115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummarySurround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
Associated Products (130)Associated Documents - April 1, 2015•Document ID: 10152306Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130315
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"
Associated Products (79)Associated Documents - April 1, 2015•Document ID: 10152305Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryEngine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (76)Associated Documents - April 1, 2015•Document ID: 10152302Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B120115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: ? 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
Associated Products (19)Associated Documents - April 1, 2015•Document ID: 10152301Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B110614
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Inf
Associated Products (59)Associated Documents - March 1, 2015•Document ID: 10147690Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B840514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
Associated Products (150)Associated Documents - March 1, 2015•Document ID: 10147675Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- B510215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Lubricate Rear Door Seam Seals. Under certain circumstances, the rear door seam seal may stick to the front door. Customers may be dissatisfied by the additional effort required to open the door. AFFECTED VEHICLES This Service Action involves F10 models produced from October 28, 2014 to January 12, 2015. First check if a Service Action label with a code number 731 is already attached to the B-pillar. If a code number 731 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Insufficient lubrication of the seam seal"
Associated Products (15)Associated Documents - March 1, 2015•Document ID: 10147660Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B121015
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"SI B12 10 15 Engine Electrical Systems March 2015 Technical Service This Service Information bulletin supersedes SI B12 10 15 dated January 2015. designates changes to this revision SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly with ISTA/P 3.54.x or 3.55.0. It did not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12 months/15,000 km/10,000 miles"" is working properly for all other N63 vehicles produced after these dates. Incorrect coding data in the affected ISTA/P versions"
Associated Products (35)Associated Documents - March 1, 2015•Document ID: 10147658Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- B112314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySI B11 23 14March 2015 EngineTechnical Service This Service Information bulletin supersedes SI 11 23 14 dated February 2015. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Replace the Thermostat (F10). The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat. CAUSE Moisture and corrosion could develop on the electrical contacts for the heater circuit in the thermostat.
Associated Products (5)Associated Documents - March 1, 2015•Document ID: 10147656Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."
Associated Products (65)Associated Documents - March 1, 2015•Document ID: 10147655Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110715
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."
Associated Products (56)Associated Documents - March 1, 2015•Document ID: 10147653Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110515
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N20 and N55 Engine: Engine Oil Filter Application for Plastic Oil Filter Housing. The current version of EPC does not provide all available options for the engine oil filters used in the N20 and N55 engines produced with a ""plastic"" oil filter housing. The illustration below will help identify the proper engine oil filter application until the EPC is corrected."
Associated Products (26)Associated Documents - March 1, 2015•Document ID: 10147652Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
Associated Products (79)Associated Documents - March 1, 2015•Document ID: 10040845Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
- Mfr Comm. #:
- SIB-11-07-11
- Date Added:
- September 13, 2011
- Manufacturer:
- BMW
SummaryBMW: LOSS OF PERFORMANCE AND TURBOCHARGER NOISE DUE TO THE OIL SUPPLY RESTRICTED, CAUSING OIL STARVATION AND RESULTING IN THE SEIZING OF THE TURBOCHARGER ASSEMBLY. *RM UPDATED 7/09/13. *PE UPDATED 9/25/15. *PE
Associated Products (14)Associated Documents