Mercedes-Benz SL-Class Service Bulletins
418 manufacturer communications on file.
- May 2, 2025•Document ID: 11018213Over The AirELECTRICAL SYSTEM
- Mfr Comm. #:
- OTA-5497821/22
- Date Added:
- May 9, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the coding for the electronic ignition lock control unit does not correspond to the latest series production configuration. The electronic ignition lock control unit will be updated to change the logic for locking and unlocking the vehicle via the door handles. To unlock the vehicle, the large outer contact surface of the door handle must be touched. To lock the vehicle, the small, recessed contact surface of the door handle must be touched. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.
Associated Products (13)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz E-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz S-ClassAssociated Documents - May 2, 2025•Document ID: 11018206Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI54.10-P-071499
- Date Added:
- May 9, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM and N73/3 EZS CUL • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".
Associated Products (107)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class+ 87 moreAssociated Documents - May 2, 2025•Document ID: 11018204Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; STEERING; LANE DEPARTURE: ASSIST
- Mfr Comm. #:
- LI46.10-P-078012
- Date Added:
- May 9, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).
Associated Products (57)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class+ 37 moreAssociated Documents - April 29, 2025•Document ID: 11017498Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- LI01.00-P-078172
- Date Added:
- May 2, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Dull thumping noise or ticking noise under the vehicle in the area of the engine/two-mass flywheel/transmission. Is significantly perceptible at the front right wheel well and can also be faintly heard in the vehicle interior. Cause The ticking noise occurs in idle operation in drive program C & S at 780 rpm when the state of charge of the battery is over 65% and the load requirement at the belt-driven starter alternator is simultaneously over 25 Nm. The load requirement can occur due to a number of auxiliary consumers (e.g. air conditioning system, steering wheel or seat heating, etc.). Remedy Switch off the auxiliary consumers and check whether the noise goes away. Remedial action by means of software update under development. Do not replace any parts 1.If the vehicle has less than 2,000 miles: • This is a normal run in period feature and will go away after the odometer has reached 2,000 miles. 2.If the vehicle has more than 2,000 miles: Create TIPS case and send to HQ together with the following documents: • Videos of the problem from the exterior and in the vehicle interior • Control unit log, engine N3/10 (ME) • Control unit log, drivetrain N127 (PTCU) • Control unit log, DC/DC converter N83/12 (DDW) • Control unit log, 48 V battery G1/13 (48 V LIB) • Control unit log, electronic ignition lock N73 (EZS)
Associated Products (5)Associated Documents - April 28, 2025•Document ID: 11017593Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI27.60-P-076554
- Date Added:
- May 2, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint • Hard 1-2 shift • Jerky shifting • Jolting when moving off Cause Insufficient data points for the adaptation limits algorithm Remedy A software bundle has been released. Please check for available software in the VGS Control Unit. Please carry out the following: • Update all control units included with VGS Control Unit software update • Check the transmission oil level and correct if necessary • Rinse the valves 3 times via XENTRY • Perform a stationary standstill adaptation • Collect EEPROM data If the problem persists, please perform driving adaptations of the 4-5 upshift (4-5 shift adapts K81 for 1-2) at least ten to fifteen times: • Level track (no incline/decline) • Slippery drive program • Display the torque in the instrument cluster: The torque must be between 100 and 250 Nm, preferably closer to the maximum torque • Constant engine torque • Engine speed under 2500 rpm • Do not shift via paddle • Collect a new EEPROM data after all adaptions are complete If the problem persists OR this is a return visit after the software update, please create a TIPS case with the following attachments: • Initial Quick Test w/ Freeze frame data • VGS Control Unit Log • All collected EEPROM files
Associated Products (4)Associated Documents - April 28, 2025•Document ID: 11017500Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078896
- Date Added:
- May 2, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.
Associated Products (273)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 253 moreAssociated Documents - April 28, 2025•Document ID: 11017496Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078301
- Date Added:
- May 2, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.
Associated Products (273)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 253 moreAssociated Documents - April 25, 2025•Document ID: 11017218Over The AirAIR BAGS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- OTA - 20250425
- Date Added:
- April 24, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the airbag control unit software does not correspond to the latest series production configuration. The airbag control unit will be updated to improve the vehicle charging functionality during future OTA updates. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.
Associated Products (9)Associated Documents - April 21, 2025•Document ID: 11017217Service Bulletin/Repair InstructionsVISIBILITY/WIPER
- Mfr Comm. #:
- LI83.30-P-079081
- Date Added:
- April 24, 2025
- Manufacturer:
- MERCEDES-MAYBACH
SummaryComplaint Random heating of air conditioning system. Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored). or The temperature sensor in the overhead control panel measures an incorrect temperature (the temperature value can be checked against the actual value in the overhead control panel) If the above-mentioned fault code is not present, the cause could be malfunction on the air conditioning system. Remedy If one of the above-mentioned fault codes should occur, a TIPS case must be created here. If the above fault codes or actual value differences are present in the OCP - please send the case to the Body/Chassis/ Entertainment inbox. Otherwise, the case must be sent to the HV/LV inbox for support in A/C diagnosis. *** It is not necessary to replace the overhead control panel ***
Associated Products (49)2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class+ 29 moreAssociated Documents - April 21, 2025•Document ID: 11017204Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- LI61.20-P-077105
- Date Added:
- April 24, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Cracking/clicking noise from underbody when driving slowly (around curves); see attachment. Cause Potential causes: • Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) • Relative movement between front and rear engine compartment lining • Torque loss of the screw connection • Accumulation of stones and dirt Remedy • Screw connection in K0-design level (vehicle compressed) and taking into account the correct screw sequence • Additional screw connection points (minimization of relative movement) • Increase in tightening torque • Integration of spacer rings (reduction of accumulation of stones and dirt) -> see underfloor paneling rework instructions 1. Create a TIPS case and send to Body/Chassis/Entertainment inbox. 2. Attach video/recording of the noise problem to the case. Be sure the recording is clear and audible. 3. After entering the TIPS case, the aftersales kit required for rework is sent (the required parts are not yet available via the replacement parts service). 4. After receiving the aftersales kit (A2326207003), check the contents: 22 screws (A0109902604) / 14 rivet nuts + 1 replacement rivet nut (A0009902349) / 4 spacer rings (A2326207203) Underfloor paneling rework 1. Disassemble underfloor paneling. If front and rear engine compartment lining are bonded to one another, order new parts (A2326201101, A2326268900). 2. Clean underfloor paneling and integral carrier. 3. Mark four additional screw connection points on the front engine compartment lining (see attachment 1). See appendix 2 for dimensions. 4. Drill holes with d=9 mm on the markings. 5. Screw front and rear engine compartment lining together using the screw connection points already available (see attachment 3). Both linings are therefore aligned to one another. Important: Pay attention to alignment of the elongated holes on the external edges. 6. Drill into the rear engine compartment lining using the four additional holes with d=9 mm (see attachment 4). 7. Disassemble front and rear engine compartment lining. 8. Drill out three existing rivet nuts with d=9 mm (see attachment 5). 9. Insert seven new rivet nuts (A0009902349) (see attachment 6). 10. Drill out seven existing rivet nuts in the integral carrier with d=9 mm (see attachment 7). Caution: Do not damage integral carrier. 11. Remove remaining rivets that have fallen off from the integral carrier using a magnetic tube (see attachment 8). 12. Insert new rivet nuts (A0009902349) in the integral carrier (see attachment 9). 13. Fix four spacer rings (A2326207203) in place using bonding points between underfloor paneling and integral carrier (for position, see attachment 10 and attachment 11). Caution: No adhesive can be applied to the contact areas (risk of torque loss). 14. Install underfloor paneling on vehicle with 17 Nm (observe screw sequence in attachment 12). Important: Use screw item number A0109902604.
Associated Products (7)Associated Documents - April 21, 2025•Document ID: 11017118Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- LI91.10-P-079211
- Date Added:
- April 22, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Seat backrest of front seat collides with the installed draft stop in the rearmost position. Cause The seat can be adjusted too far to the rear beyond the correct limit (combination of seat adjustment and seat backrest angle). Remedy Remedy SW A2329038302 for the SEAT control unit to limit the adjustment range of the mechanical seat components.
Associated Products (4)Associated Documents - April 17, 2025•Document ID: 11017220Service CampaignELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- NCU - 2025040004
- Date Added:
- April 24, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software may not correspond with current production specifications. There is a possibility that the dynamic driving profile may not be accurately calculated, which could possibly lead to an unsuccessful diagnostic routine for the lambda sensors. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
Associated Products (4)Associated Documents - April 17, 2025•Document ID: 11017078Service CampaignELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- NCU - 2025040003
- Date Added:
- April 16, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software does not correspond to current production specifications. The diagnosis routine for the pressure sensor in the crankcase ventilation system may be populated with incorrect data. As a consequence, the check engine light may illuminate after the engine is switched off even though there is no functional impairment. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
Associated Products (4)Associated Documents - April 11, 2025•Document ID: 11017516Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STEERING
- Mfr Comm. #:
- LI46.10-P-078012
- Date Added:
- May 2, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Test: Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Reset the HOSWD control unit in line with the guided test in Xentry. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> replace steering wheel rim. If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no defect is visible: Please do not replace the steering wheel, but wait for new coding parameters which should be available 05/2025. Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the
Associated Products (60)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class+ 40 moreAssociated Documents - April 7, 2025•Document ID: 11017037Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI54.71-P-079104
- Date Added:
- April 15, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off Traffic Sign Assist until the investigation is completed. Once completed this LI will be updated. No TIPS case is necessary. Do not replace parts.
Associated Products (39)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class+ 19 moreAssociated Documents - April 7, 2025•Document ID: 11017229Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- LI42.10-P-063502
- Date Added:
- April 25, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.
Associated Products (166)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT+ 146 moreAssociated Documents - March 24, 2025•Document ID: 11016043Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI27.35-P-079039
- Date Added:
- March 27, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint A clicking/ticking/taping noise from underneath the vehicle with engine off during ECO stop event or after parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps.
Associated Products (90)2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class+ 70 moreAssociated Documents - March 21, 2025•Document ID: 11016038Over The AirELECTRICAL SYSTEM
- Mfr Comm. #:
- OTA - 5496236
- Date Added:
- March 27, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the software for the airbag control unit does not correspond to the latest series production configuration. The airbag control unit will be updated to improve the vehicle charging functionality during future OTA updates. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.
Associated Products (9)Associated Documents - March 10, 2025•Document ID: 11015614Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- LI46.35-P-076566
- Date Added:
- March 14, 2025
- Manufacturer:
- MERCEDES-MAYBACH
SummaryComplaint A squeaking noise comes from the electric power steering; see video with example. Cause Toothed rack in the area of the screw drive of the electric power steering needs additional grease. Remedy 1. Lift the vehicle and remove the center engine compartment lining; for basic data, see WIS AR61.20-P-1105S 2. Loosen the bellows of the electric power steering on the right of the steering gear and slide outward on the tie rod – the tie rods do not need to be removed! For basic data, see WIS AR46.40-P-9998S 3. Turn the wheels fully to the right. The screw drive of the rack-and-pinion steering becomes visible. See picture 1 of screw drive 4. Clean the screw drive with a clean cloth and remove the existing grease. See picture 2 of cleaned screw drive 5. Prepare a clean brush for greasing the screw drive and, if necessary, mask off the metal sleeve of the brush or similar components to avoid damage to the steering housing or to the screw drive of the toothed rack. See picture 3 with example brush 6. Apply a sufficient amount of long-life grease (A001 989 84 51 09) to the screw drive of the toothed rack with the brush, making sure that this is applied evenly all around; see picture 4 of greased screw drive 7. Reinstall the steering bellows, making sure to replace the inner clamp! Important: The contact surfaces of the bellows and the rack-and-pinion steering should be coated with a thin layer of Renolit (Renolit CX-FO 20, A094 989 38 00 11). For basic data, see WIS AR46.40-P-9998S 8. Move the rack-and-pinion steering several times from one steering limitation to the other to ensure that the grease is evenly distributed in the housing. 9. Assemble in the reverse order.
Associated Products (14)2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz S-ClassAssociated Documents - March 10, 2025•Document ID: 11015559Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- LI61.20-P-077105
- Date Added:
- March 12, 2025
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Cracking/clicking noise from underbody when driving slowly (around curves); see attachment. Cause Potential causes: • Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) • Relative movement between front and rear engine compartment lining • Torque loss of the screw connection • Accumulation of stones and dirt Remedy • Screw connection in K0-design level (vehicle compressed) and taking into account the correct screw sequence • Additional screw connection points (minimization of relative movement) • Increase in tightening torque • Integration of spacer rings (reduction of accumulation of stones and dirt) -> see underfloor paneling rework instructions 1. Create a TIPS case 2. After entering the TIPS case, the aftersales kit required for rework is sent (the required parts are not yet available via the replacement parts service). 3. After receiving the aftersales kit (A2326207003), check the contents: 22 screws (A0109902604) / 14 rivet nuts + 1 replacement rivet nut (A0009902349) / 4 spacer rings (A2326207203) Underfloor paneling rework 1. Disassemble underfloor paneling. If front and rear engine compartment lining are bonded to one another, order new parts (A2326201101, A2326268900). 2. Clean underfloor paneling and integral carrier. 3. Mark four additional screw connection points on the front engine compartment lining (see attachment 1). See appendix 2 for dimensions. 4. Drill holes with d=9 mm on the markings. 5. Screw front and rear engine compartment lining together using the screw connection points already available (see attachment 3). Both linings are therefore aligned to one another. Important: Pay attention to alignment of the elongated holes on the external edges. 6. Drill into the rear engine compartment lining using the four additional holes with d=9 mm (see attachment 4). 7. Disassemble front and rear engine compartment lining. 8. Drill out three existing rivet nuts with d=9 mm (see attachment 5). 9. Insert seven new rivet nuts (A0009902349) (see attachment 6). 10. Drill out seven existing rivet nuts in the integral carrier with d=9 mm (see attachment 7). Caution: Do not damage integral carrier. 11. Remove remaining rivets that have fallen off from the integral carrier using a magnetic tube (see attachment 8). 12. Insert new rivet nuts (A0009902349) in the integral carrier (see attachment 9). 13. Fix four spacer rings (A2326207203) in place using bonding points between underfloor paneling and integral carrier (for position, see attachment 10 and attachment 11). Caution: No adhesive can be applied to the contact areas (risk of torque loss). 14. Install underfloor paneling on vehicle with 17 Nm (observe screw sequence in attachment 12). Important: Use screw item number A0109902604.
Associated Products (4)Associated Documents