Mercedes-Benz CLE Service Bulletins

175 manufacturer communications on file.

• September 26, 2026•Document ID: 11038188

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-080896

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

  Associated Products (91)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT+ 71 more
  Associated Documents

  • DownloadMC-11038188-0001.pdf↗
• September 26, 2026•Document ID: 11038185

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI18.00-P-073137

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Sporadic warning message in instrument cluster "Engine oil pressure, stop switch off vehicle" (or similar) is shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1‑ Read off oil level in instrument cluster and correct if necessary. 2‑ Perform approx. 10‑15 engine starts, then clear fault codes. 3‑ Perform road test with vehicle. If fault code reoccurs during road test: Install new directional control valve.

  Associated Products (38)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz AMG GT+ 18 more
  Associated Documents

  • DownloadMC-11038185-0001.pdf↗
• September 22, 2026•Document ID: 11038186

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-078779

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038186-0001.pdf↗
• September 14, 2026•Document ID: 11038217

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038217-0001.pdf↗
• September 14, 2026•Document ID: 11037834

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.31-P-080353

  Date Added:

  October 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Whining / humming noises (described as foghorn‑like) from the drivetrain in the rear axle area during cornering. (figure 1) On the above‑mentioned vehicles with a mileage up to 15,000 km (about 9,300 mi), noises can occur from the rear axle differential. Cause Drivetrain resonance caused by the gear mesh of the ring and pinion in the rear axle differential in combination with installed damper elements on the axle shafts. Remedy For precise noise analysis and localization, use the chassis ear/NVH kit and the following driving procedure: 1. Drive the vehicle in a tight circle with the steering at full lock in both clockwise and counter clockwise directions. ‑ Vary engine load during the maneuvers If a foghorn‑like noise occurs comparable to the reference video, the vehicle exhibits the condition If the noise is present: 1. Add 15 ml of additive (Friction Modifier) into the rear axle differential via the filler plug IMPORTANT NOTE: Do NOT use Friction Modifier in vehicles equipped with an electronically controlled locking differential (Code 467). 2. Tighten the filler plug 3. Drive the vehicle until the rear axle differential reaches operating temperature Note: Proper activation of the additive requires elevated oil temperatures After the test drive to operating temperature, evaluate the noise when the rear axle is cold and when warm. If the noise is no longer present: The issue is resolved and the vehicle can be released. If there is noticeable improvement: The vehicle can be released with the explanation that the noise will gradually disappear over an extended driving distance. If the noise is still present and remains unchanged: Replace the rear axle differential.

  Associated Products (41)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class+ 21 more
  Associated Documents

  • DownloadMC-11037834-0001.pdf↗
• September 11, 2026•Document ID: 11037806

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-079104

  Date Added:

  October 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("‑ ‑"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the re‑check function in the same location. NOTE: Updated head unit software for AMG's has NOT been released yet. ETA 12/2026. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: • Video of the concern. • Exact location (latitude and longitude is best)

  Associated Products (50)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class+ 30 more
  Associated Documents

  • DownloadMC-11037806-0001.pdf↗
• September 10, 2026•Document ID: 11037738

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI72.40-P-080776

  Date Added:

  October 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint When using the one‑touch (automatic) window closing function on one or both front door windows, the customer may report one of the following concerns: • The window begins closing, then reverses direction before reaching the fully closed position. • The window loses normalization and can only be closed by pulling and holding the window switch until the window reaches the fully closed position. Cause Currently under investigation. Remedy Please submit a TIPS case to the Body/Chassis/Entertainment inbox and provide the following information: • A detailed description of the client's concern • Does the window reverse (obstruction detection) or has it lost normalization? • Is the condition reproducible? If yes, please provide a video demonstrating the concern • Initial Quick Test • Control Unit Log of the relevant Door Control Unit • Actual Values > Power window Development data (Reversal, Evaluation of window raising, & Learned values)

  Associated Products (4)

  2027 Mercedes-Benz CLE2026 Mercedes-Benz CLE2025 Mercedes-Benz CLE2024 Mercedes-Benz CLE
  Associated Documents

  • DownloadMC-11037738-0001.pdf↗
• September 4, 2026•Document ID: 11037489

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-079747

  Date Added:

  September 26, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The Apple Music app is no longer available in the head unit apps menu after updating the software of the (A26/17 ‑ MBUX multimedia system + instrument cluster (head unit)) to E333.8 / A236 904 19 00. Cause Head unit software (CIVIC206) Remedy NOTE: Do not replace any component parts The new Apple Music app version is now available. The app should automatically be downloaded and available. If the app is not shown available, check via the Mercedes‑Benz App Store directly in the vehicle and download the app. NOTE: Please refer to this LI in the warranty claim in the "Notes" section!

  Associated Products (19)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz GLC-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11037489-0001.pdf↗
• August 24, 2026•Document ID: 11036511

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; STRUCTURE:BODY

  Mfr Comm. #:

  LI72.20-P-075746

  Date Added:

  August 31, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

  Associated Products (97)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class+ 77 more
  Associated Documents

  • DownloadMC-11036511-0001.pdf↗
• August 22, 2026•Document ID: 11036608

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-079104

  Date Added:

  September 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("‑ ‑"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the re‑check function in the same location. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: • Video of the concern. • Exact location (latitude and longitude is best)

  Associated Products (43)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class+ 23 more
  Associated Documents

  • DownloadMC-11036608-0001.pdf↗
• August 15, 2026•Document ID: 11036345

  Other
  ENGINE; SUSPENSION

  Mfr Comm. #:

  PSL-NCU Return Parts 8/14

  Date Added:

  August 26, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, September 3rd, 2026. After September 3rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

  Associated Products (8)

  2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2023 Mercedes-Benz C-Class2022 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11036345-0001.pdf↗
• August 12, 2026•Document ID: 11036142

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  August 12, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (119)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 99 more
  Associated Documents

  • DownloadMC-11036142-0001.pdf↗
• August 6, 2026•Document ID: 11036101

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  August 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11036101-0001.pdf↗
• August 4, 2026•Document ID: 11036091

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-080806

  Date Added:

  August 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint DAB, FM, or SDARS radio reception is limited, only a few stations are found. Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.

  Associated Products (23)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class+ 3 more
  Associated Documents

  • DownloadMC-11036091-0001.pdf↗
• August 3, 2026•Document ID: 11035755

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI33.30-P-080490

  Date Added:

  August 5, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Leakage/oil leakage at drive pinion sealing ring (input shaft) (Figures 1-2) Minor leakage/slight seepage at coupling flange nut at drive pinion (Figures 3-4) Cause Damage to sealing ring during production process or insufficient use of lubricating paste during assembly of collar nut on coupling flange Remedy If any of the above-mentioned customer complaints are present, or if oil leakage or seepage is found at the front axle differential during a workshop visit, the following steps must be performed: If oil leakage is found at drive pinion sealing ring (input shaft): • Remove coupling flange from differential, AR33.30-P-0550WT • Replace drive pinion sealing ring • New collar nut (for coupling flange), part number A 221 353 03 72, on contact surface and coat the 1st thread (from contact side to coupling flange) with lubricating paste (Figures 5-6) • Install coupling flange. If oil leakage or slight seepage is found at coupling flange nut to drive pinion: • Remove coupling flange from differential, AR33.30-P-0550WT • Clean threads on input shaft • new collar nut (for coupling flange), part number A 221 353 03 72, on contact surface and coat the 1st thread (from contact side to coupling flange) with lubricating paste (Figures 5-6) • Install coupling flange.

  Associated Products (22)

  2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class+ 2 more
  Associated Documents

  • DownloadMC-11035755-0001.pdf↗
• July 31, 2026•Document ID: 11035487

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI80.35-P-080195

  Date Added:

  August 3, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint "Key Not Detected" message appears on the IC while driving even though the key is in the car and no doors have been opened. Cause EZS SW Remedy Confirm that the message is not due to the driver's door being opened and that the door latch is reading properly. For vehicles that do not have the above issues, EZS SW is released for option code 805 ONLY. For all other vehicles, the SW is still in development. Current workaround is to ensure that the key is left on the antenna in the storage compartment.

  Associated Products (3)

  2026 Mercedes-Benz CLE2025 Mercedes-Benz CLE2024 Mercedes-Benz CLE
  Associated Documents

  • DownloadMC-11035487-0001.pdf↗
• July 23, 2026•Document ID: 11035220

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI80.35-P-080195

  Date Added:

  July 24, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint "Key Not Detected" message appears on the IC while driving even though the key is in the car and no doors have been opened. Cause Possible SW Remedy Confirm that the message is not due to the driver's door being opened and that the door latch is reading properly. For vehicles that do not have the above issues, SW is released for option code 805 ONLY. For all other vehicles, the SW is still in development. Current workaround is to ensure that the key is left on the antenna in the storage compartment.

  Associated Products (4)

  2026 Mercedes-Benz CLE2025 Mercedes-Benz CLE2024 Mercedes-Benz CLE2023 Mercedes-Benz CLE
  Associated Documents

  • DownloadMC-11035220-0001.pdf↗
• July 17, 2026•Document ID: 11035230

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-080806

  Date Added:

  July 27, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After an "Over the Air" update (OTA), FM or SDARS radio reception is limited; only a few stations are found. Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.

  Associated Products (23)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class+ 3 more
  Associated Documents

  • DownloadMC-11035230-0001.pdf↗
• July 14, 2026•Document ID: 11035005

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  July 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11035005-0001.pdf↗
• July 9, 2026•Document ID: 11035016

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-079104

  Date Added:

  July 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

  Associated Products (43)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class+ 23 more
  Associated Documents

  • DownloadMC-11035016-0001.pdf↗