Mazda CX-5 Service Bulletins (2014)
789 manufacturer communications on file.
- March 26, 2018•Document ID: 10134928Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- 01-008-18-3451
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryThis service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
Associated Products (138)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda CX-9+ 118 moreAssociated Documents - March 26, 2018•Document ID: 10134706Service Bulletin/Repair InstructionsSEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER
- Mfr Comm. #:
- 09-017-18-3437
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit inoperative driver and/or front passenger side seat warmer(s) in any mode (High, Mid and Low). This may be caused by repeated load applied to the seat cushion (1) while the seat is occupied. A section of the heater mat (2) just above the reinforcement rod (3) in the cushion pad contacts internal heater mat wire and causes damage (4).
Associated Products (4)Associated Documents - March 26, 2018•Document ID: 10134703Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- 09-019-18-3450
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryThis service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.
Associated Products (138)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda CX-9+ 118 moreAssociated Documents - March 22, 2018•Document ID: 10134702Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 09-014-18-3443
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryWhen encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
Associated Products (141)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda22016 Mazda Mazda32016 Mazda Mazda52016 Mazda Mazda62016 Mazda MX-5+ 121 moreAssociated Documents - March 22, 2018•Document ID: 10134701Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:TAIL LIGHTS; EXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 09-011-18-3448
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
Associated Products (93)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda CX-9+ 73 moreAssociated Documents - March 22, 2018•Document ID: 10134700Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 02-005-18-3444
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryBeginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
Associated Products (25)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda22018 Mazda Mazda32018 Mazda Mazda62017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda22017 Mazda Mazda32017 Mazda Mazda62016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda22016 Mazda Mazda32016 Mazda Mazda62015 Mazda CX-52015 Mazda Mazda3+ 5 moreAssociated Documents - March 22, 2018•Document ID: 10134699Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 00-001-18-3446
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryMazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Associated Products (131)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda52016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-5+ 111 moreAssociated Documents - March 20, 2018•Document ID: 10134934Service Bulletin/Repair InstructionsFUEL SYSTEM, OTHER:FUEL FILTER
- Mfr Comm. #:
- RF-16-03R1
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryThe SKYACTIV®-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV® oil filters. The unique oil filter can be identified with two white bands as shown below.
Associated Products (27)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda Mazda3+ 7 moreAssociated Documents - March 9, 2018•Document ID: 10134691Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE
- Mfr Comm. #:
- 01-006-18-3429
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryWhen the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.
Associated Products (16)Associated Documents - February 22, 2018•Document ID: 10136325Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- 01-005-18-3415
- Date Added:
- May 7, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
Associated Products (20)2018 Mazda CX-32018 Mazda Mazda32018 Mazda Mazda62017 Mazda CX-32017 Mazda CX-52017 Mazda Mazda32017 Mazda Mazda62016 Mazda CX-32016 Mazda CX-52016 Mazda Mazda32016 Mazda Mazda62015 Mazda CX-52015 Mazda Mazda32015 Mazda Mazda62014 Mazda CX-52014 Mazda Mazda32014 Mazda Mazda62013 Mazda CX-52013 Mazda Mazda32012 Mazda Mazda3Associated Documents - February 16, 2018•Document ID: 10134925Service Bulletin/Repair InstructionsAIR BAGS; EQUIPMENT
- Mfr Comm. #:
- MT-003-18
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryThe Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
Associated Products (94)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda CX-9+ 74 moreAssociated Documents - January 29, 2018•Document ID: 10129574Service Bulletin/Repair InstructionsSEATS:FRONT ASSEMBLY:POWER ADJUST
- Mfr Comm. #:
- 09-005-18-3414
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction and noise.
Associated Products (14)Associated Documents - January 5, 2018•Document ID: 10129564Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SHOCK ABSORBER
- Mfr Comm. #:
- 02-002-18-3300d
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).Front Shock Absorber Front Lower Arm To eliminate the noise, the following mass-production changes have been made: 1. The material and production method of the front strut bearing (A) has been changed. (CX-5 and Mazda6) 2. A protector has been installed onto the coil spring. (CX-5 and Mazda6) 3. The shape of the bump stopper (C) will be modified in the future. (Mazda6 only) 4. The shape of the coil spring has been changed. (CX-3 only) 5. Friction of the lower arm bushing has been reduced by adding a dry coating. (CX-5 and Mazda6). NOTE: The piston rod nut (B) requires replacement.
Associated Products (10)Associated Documents - January 4, 2018•Document ID: 10129353Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- SA-001-18
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummaryThe MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
Associated Products (17)Associated Documents - December 18, 2017•Document ID: 10185794Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; AIR BAGS
- Mfr Comm. #:
- 01-001-17
- Date Added:
- January 25, 2021
- Manufacturer:
- MAZDA
SummarySome vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.
Associated Products (12)Associated Documents - December 18, 2017•Document ID: 10129327Service Bulletin/Repair InstructionsSTEERING: STEERING WHEEL/HANDLE BAR
- Mfr Comm. #:
- 06-001-17-3307b
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Associated Products (15)Associated Documents - December 5, 2017•Document ID: 10129368Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE
- Mfr Comm. #:
- MT-021-17
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
Associated Products (27)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda Mazda3+ 7 moreAssociated Documents - November 20, 2017•Document ID: 10188487Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP:MOUNTING PLATE/FLANGE; EQUIPMENT
- Mfr Comm. #:
- 03-002-17-3394
- Date Added:
- March 8, 2021
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit an oil leak from the companion flange area (A) of the transfer unit. This concern may be caused by companion flange oil seal wear. The oil seal has been improved to increase the wear resistance.
Associated Products (4)Associated Documents - November 13, 2017•Document ID: 10188482Service Bulletin/Repair InstructionsSEATS:FRONT ASSEMBLY:POWER ADJUST; EQUIPMENT; ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:CABLE/CORD:ACCESSORY
- Mfr Comm. #:
- 09-011-17-3339a
- Date Added:
- March 8, 2021
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit excessive noise when operating either front power seat forward or backward. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the case due to inadequate fabric wrapped around the cable. The fabric thickness has been increased to eliminate the noise.
Associated Products (8)Associated Documents - November 10, 2017•Document ID: 10188481Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE; SUSPENSION:FRONT:SHOCK ABSORBER
- Mfr Comm. #:
- 02-009-17-3392
- Date Added:
- March 8, 2021
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold.
Associated Products (9)Associated Documents