GMC Yukon Complaints (2025)

51 consumer complaints on file.

#11759923August 27, 2026
ENGINE
As my wife was driven she heard some noise and notice she was losing power. She pull off the side of the road and the car shut off. Could not restart. This happen about 11:30 am on 8/14/26 Got towed to Salida Dealer called Faricy GMC about 3:30 pm. Dealer said it was a complete engine failure and engine needed to be replaced.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11758878August 23, 2026
ENGINE, FUEL/PROPULSION SYSTEM
Vehicle loss of power on the Interstate at a high rate of speed. Vehicle would not start and could not be put in Neutral to safely remove from road.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11754669August 4, 2026
STEERING, ELECTRICAL SYSTEM
The progressive failure of the factory steering wheel adhesive on my 2025 GMC Yukon creates an immediate, active safety hazard during vehicle operation. The material failure and sticky glue are localized directly around the integrated heating element of the steering wheel. This failure severely impacts driving maneuvers as well as a potential electrical fire hazard. The liquefied glue residue is incredibly sticky and continually transfers to the driver’s hands, resulting in a compromised, slippery grip on the steering wheel. During active driving maneuvers, such as hand-over-hand turning, navigating sharp curves, the loose edges of the peeling leather and separating trim physically catch on the driver's palms. This restricts smooth wheel rotation, disrupts natural hand movement, and threatens a sudden, temporary loss of steering control. This manufacturing defect introduces severe driver distraction and physical interference with critical steering components while driving, compounded by a potential thermal or electrical defect in the steering wheel heating assembly.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11754040July 31, 2026
POWER TRAIN, ELECTRICAL SYSTEM, ENGINE
GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11753795July 30, 2026
BACK OVER PREVENTION
The contact owns a 2025 GMC Yukon. The contact stated that while the vehicle was shifted into reverse, the rear-view camera displayed a black screen. The image in the rear-view camera was not visible, specifically in areas where there were reflective lights. The dealer was contacted and assisted the contact with the brightness options on the rear-view camera and stated there was no failure with the camera. The camera was not repaired or replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 16.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745319June 19, 2026
VISIBILITY/WIPER, UNKNOWN OR OTHER
On multiple occasions the center screen has been non operational when we start the car and just shows a black screen. The volume knob and screen power button are non-responsive. When this occurs the backup camera is inoperable, which is mandatory safety equipment. the HVAC also cannot be adjusted which could cause a windshield fogging condition which is a safety concern. The vehicle has been to the dealer 3 times for screen problems and the issue has not been resolved. When this occurs the problem persists for a few ignition cycles or for up to a couple of days and then will start functioning again. We have not been able to determine any specific condition that is causing the failure.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11737169May 11, 2026
ENGINE
Just over 6k miles, engine failure.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11735631May 4, 2026
ENGINE
The engine has seized and was replaced
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11729983April 8, 2026
ENGINE
My engine completely failed on March 19, 2026 and it is currently at Sterling GMC in Bryan Texas waiting for a backorder engine as it needs to be completely replaced
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726887March 25, 2026
UNKNOWN OR OTHER, BACK OVER PREVENTION: SENSING SYSTEM: CAMERA, BACK OVER PREVENTION:DISPLAY FUNCTION
My 2025 GMC Yukon's infotainment system has repeatedly failed. The huge center screen frequently goes black upon starting the car. Once the screen goes black you are unable to control literally dozens of the vehicle's features including but not limited to climate controls, safety features, heated/ventilated seats, gps, lane assist, the radio, no backup camera, etc. When the screen blacks out, the vehicle automatically turns the heat on to 76 degrees every single time and blows hot air from the front windshield defogger vents only. The list of features controlled by the touch screen is quite enormous. I have taken the vehicle to the GMC dealer four (4) times for software updates, none of which solved the problem and they have admitted they have no fix for this issue. The issue is widespread, as I have encountered literally hundreds of owners online like myself dealing with the very same problem; brand new cars that just do not work. GMC has done absolutely nothing to get to the bottom of this.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726211March 22, 2026
ENGINE
Engine failure while driving at 60mph that started with a loud knocking sound to eventual engine failure where it wouldnt turn over. Vehicle has 9600 miles and has had issues since day one of leaving lot requiring fuel injector, intake manifold gasket, lifter and rod with last fix being new coil and spark plug that supposedly fixed issue. The most recent engine failure put my family and kids in danager given 100 degree weather in middle of desert on a small highway with very limited cell service. Vehicle provided no warning lights. Vehicle was towed to dealership and I have not received an update. Vehicle has not been inspected by polive or insurance or others.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11724693March 16, 2026
FORWARD COLLISION AVOIDANCE: WARNINGS, AIR BAGS, ENGINE
Purchased new August 29, 2025 On 12/3/25- Mileage 4495. Took vehicle in for first maintenance service. Tire rotation and oil change. On 1/7/26- Reported grinding noise we had began noticing when starting vehicle. Engine light Service ESC. Service Traction control. Reported to Ben Mynatt GM. On 1/8/26 Mileage 7120- Took Yukon in for service due to grinding noise. Due for 6 module updates and 3 stand alone updates. On 2/16/26 Noticed ticking noise when heat in on high. Scheduled service for 2/26. On 2/24/26 Smell from car, oil reporting low. Dip stick completely dry. Sent email and photos to Ben Mynatt Service. On 2/26/26 Took vehicle in for service. Service advised to start oil consumption test. Ordered blower motor for the squealing noise. Cyl 3 misfire. Was told by the dealer, possibly needs engine 2/27/26 Took Vehicle in for service Check engine light on. Bearing inside blower motor and blower motor replaced. Replaced coil cyl 3 Tire Rotation 2/28/26 Car shaking, smoking, engine light on. Terrible smell from exhaust. Engine light came on, Service ESC, Service Traction Control, Forward Collision Unavailable, Reduced Acceleration Drive with Care Alert. GMC Alert: Service the engine and transmission system immediately alert, Engine Light on. Vehicle Approx miles. Codes misfires to cylinder 3. Took vehicle right to Service Dept. Codes Cleared. Replaced coil on cyl 3 March 7th - Mileage 11,200 Car shaking vigorously! Engine light flashing. Loud knocking coming from vehicle. GMC alert: Service the engine and transmission system immediately alert. Emission system- service now. Engine and Transmission System Service now. Service antilock braking, Stabilitrack stability control systems and airbag system. Service Air Bag System. Emailed to Service March 9th. Took vehicle in. Cylinder 3 & 8 misfire code cold start rough idle code. Oil consumption using approx1 qt of oil/500 miles. Vehicle unsafe risk of engine seizure, fire risk and loss of acceleration is extreme danger
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11722657March 7, 2026
ENGINE
Vehicle went into limp mode while driving on the highway. Onstar said it was the transmission. Checked the oil and smoke was billowing out of the dip stick and there was no oil. None of the sensors indicated that there was low oil. After sitting and waiting for a tow truck rechecked the oil with the dipstick and there was oil in it. Now requires a new engine.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11720219February 24, 2026
ENGINE
The contact owns a 2025 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly went into LIMP Mode with a limited speed availability message displayed. The vehicle was restarted; however, the failure recurred. The vehicle was taken to the dealer, where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 8,837
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11716889February 9, 2026
ENGINE
The 3.0L diesel motor failed around 5700 miles. The thrust bearing failed and the engine and the turbo needed to be replaced.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11716461February 7, 2026
ENGINE
Engine started knocking and developed slow acceleration out of the blue. In addition car has locked up on freeway despite not having any cars around me. Its been in the shop for 3 days and still no diagnosis.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11715405February 3, 2026
POWER TRAIN, ENGINE
While driving on a highway, the vehicle intermittently suffers a sudden loss of engine power during acceleration, accompanied by a flashing check engine light. The most serious event occurred while merging into traffic when the vehicle failed to accelerate normally and briefly lost power, creating a risk of being struck by faster-moving vehicles. Pulling over and restarting temporarily restores normal acceleration, but the problem recurs. The malfunction appears consistent with an engine misfire/powertrain fault. An OBD scan has shown misfire-related diagnostic codes (random/multiple misfire and a cylinder-specific misfire). The condition is intermittent and often occurs after approximately 10–45 minutes of driving. The vehicle remains available for inspection. The vehicle has been presented to authorized service departments multiple times. Dealers reported they were unable to duplicate the issue during road testing and no lasting repair has been completed. The manufacturer has been contacted and the vehicle has been evaluated through authorized service channels, but the underlying cause has not been identified. This remains a safety hazard because it reduces acceleration in traffic. Incident list: • 10/25/2025 (~12:25 PM; ~3,108 miles): Loss of power while merging; flashing CEL; restart temporarily resolved. • 10/27/2025–11/04/2025: Intermittent recurrence, usually lasting a few minutes then clearing. • 11/05/2025 (~8:01 AM; ~3,641 miles): Flashing CEL and misfire/loss-of-power symptoms; taken for service. • 11/26/2025 (~10:06 AM): Another episode consistent with the same pattern. • 12/17/2025 (~8:21 AM): Another episode, including during travel to a service visit. • Ongoing: Episodes after ~10–45 minutes; sometimes requires restart to restore drivability. Observed codes: P0300 and P0301. Safety risk: loss of power during acceleration/merging increases risk of rear-end or side-impact collision.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11715402February 3, 2026
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL, FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING, LANE DEPARTURE: BLIND SPOT DETECTION
While driving on a highway, the vehicle intermittently experienced a sudden loss of engine power during acceleration, accompanied by a flashing check engine warning light. The most serious event occurred while merging into traffic, when the vehicle failed to accelerate normally and briefly lost power, creating a risk of being struck by faster-moving vehicles. After pulling over and restarting the vehicle, normal acceleration temporarily returned, but the problem has recurred multiple times. The malfunction appears to be related to an engine misfire or powertrain fault because the check engine light flashes during the events and an OBD scan has shown misfire-related diagnostic codes (random/multiple misfire and a cylinder-specific misfire). The condition is intermittent and typically occurs after the vehicle has been driven for approximately 10–45 minutes. The vehicle remains available for inspection. The vehicle has been presented to authorized service departments multiple times for diagnosis. The dealerships have reported that they were unable to duplicate the issue during road testing and no lasting repair has been completed. The manufacturer has been contacted and the vehicle has been inspected/diagnosed through authorized service channels, but the underlying cause has not been identified. The failure continues to occur intermittently and is a safety hazard because it affects acceleration in traffic. Incident list 10/25/2025 (~12:25 PM; ~3,108 miles) — While accelerating to merge onto a highway, the vehicle lost power and the check engine light flashed. The driver pulled over, shut the vehicle off, restarted, and the condition temporarily resolved, allowing the trip to continue. 10/27/2025–11/04/2025 — The same loss-of-power/misfire behavior recurred intermittently, typically lasting a few minutes before clearing. 11/05/2025 (~8:01 AM; ~3,641 miles) — The check engine light flashed again and symptoms consistent with misfire/loss of power were present. The
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11714774February 1, 2026
ENGINE, POWER TRAIN
ENGINE died rattling sound undeer car shaking loss of power
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11712964January 23, 2026
ENGINE
suddenly went into limp mode on the highway, engine had to be replaced due to bearing failure sending metal through the engine
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to GMC Yukon