Bombardier Recreational Products, Inc. (BRP) is recalling certain 2020-2023 Spyder RT and 2022-2023 Ryker motorcycles. The brake lights may stay illuminated even if the brake pedal is not pressed. As such, these motorcycles fail to comply with Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and associated Equipment."
Bombardier Recreational Products Inc. (BRP) is recalling certain 2020 Can-Am Spyder RT motorcycles. During emergency braking situations, the support which holds the brake mechanism could break, causing a total loss of braking ability.
The contact owns a 2020 Can-Am Spyder RT. The contact received notification of NHTSA Campaign Number: 23V175000 (Exterior Lighting); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
No injuries · No fire · No crash
The contact owns a 2020 Can-Am Spyder F3. The contact stated that while attempting the accelerate from a stop light, the motorcycle lost automotive power and failed to drive forward. The motorcycle was later towed to the local dealer who diagnosed that the front sprocket pulley was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was not notified of the failure. The failure mileage was 21,300.
No injuries · No fire · No crash
The contact owns a 2020 Can-Am Spyder RT. The contact stated that while driving at an undisclosed speed, she attempted to activate the cruise control, however, the vehicle failed to operate as designed. The contact then stated that she noticed that the brake light remained illuminated although the brake pedal was not depressed. The vehicle was taken to the dealer where it remained. The contact then received notification of the NHTSA Campaign Number: 23V175000 (Exterior Lighting). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure and the contact was informed that parts were not available. The failure mileage was approximately 3,000. Parts distribution disconnect.
No injuries · No fire · No crash
The Spyder brake switch started failing with less than 14K miles on the vehicle. The driver my wife, did not know it was failing, only an engine code VSS would appear and the vehicle would go into limp home mode, until it could be restarted. Checking online forms, there were several post about the brake switch. I check in our garage and discovered I could push the brake pedal and sometimes there would be a two second delay before the lights would come on. Pressing harder on the brakes made them flicker on and off. At times only half the brake lights would come on. The brake switch is located four inches off the pavement and exposed to road grime. The piston only has an O-ring and lacks a rubber boot to keep debris from entering the switch. (Like my Harley Davidson motorcycle has.) The brake switch part # 710005480 is about $45 and an two hours labor to install. The new replacement switch is #710008326, but it looks just like the switch I took off the Can Am Spyder. Some of my research showed that this brake switch has been used on most if not all Spyders and Ryker motorcycles produced by Can Am in the last few years. I did post this issue on a Spyder Facebook group and within 24 hours eight people stated they had the same issue with their new Spyder, which was repaired under warranty. I just believe it's a bad design for an exposed part four inches off the pavement. Also my wife stepping on the brakes and the brake lights not working for two seconds put her in danger of being struck by another vehicle.
No injuries · No fire · No crash
spyder f3 7000 miles.. semi automatic transmission or paddle shifter is my problem and concern.. it has gone from 25% of the time to 80% of the time as it will not allow me to manually downshift the gearbox, causing me to slow down from 60 plus mph in 6th gear to 34 mph at which point it down shifts automatically, i cant stress the importance of being able to downshift when in traffic or the need to speed up to avoid hazards or slower cars.. also when this happens i cannot put the 1000 pound bike into reverse, causing me to manually push it backwards..3 back surguries i am not exactly physically able to do.. please let BRP know this needs their attention.. it has been to the shop but they said it wasnt doing this for them, yes they are liars, it doesnt throw a problem code to their computer therfore they dont know how to fix it, does that make sense? i need some answers and am going to be talking to BRP directly.. please keep me safe..
No injuries · No fire · No crash