BMW 435i Service Bulletins
424 manufacturer communications on file.
- February 1, 2014•Document ID: 10147980Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147979Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Heating and Air Conditioner. There is an intermittent whirring noise from the IHKA system when the engine is under load between 2,000 and 3,000 rpm, and sometimes at approximately 5,000 rpm. CAUSE Vibrations from the A/C low-pressure hose are resonating into the heating and air conditioning system.
Associated Products (11)Associated Documents - February 1, 2014•Document ID: 10147978Service Bulletin/Repair InstructionsEQUIPMENT; EXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 630614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or Both Headlights Are Aimed Downwards. The customer may experience one or more of the following complaints: * One or both headlights are aimed significantly too low (jammed lower limit). * No reference run is visible on the affected headlight when the ignition is turned on and the light switch is in the auto position. * No CCM (Check Control Message) is displayed when a headlight is faulty. CAUSE * TMS-3 (Headlight driver module AHL) coding error * Defective mechanism inside the headlight
Associated Products (3)Associated Documents - February 1, 2014•Document ID: 10147974Service Bulletin/Repair InstructionsVISIBILITY:SUN/MOON ROOF ASSEMBLY
- Mfr Comm. #:
- 540213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?Sunroof Gets Stuck or Moves in Small Steps. During opening or closing the sunroof, one or more of the following situations may occur: 1. The sunroof becomes stuck 2. One-touch open and close no longer works 3. The sunroof moves in small steps. CAUSE Software error in the sunroof control module (FZD) Some or all of the following fault codes may be stored: 0x030212 - SHD: Activation timeout, no block recognition 0x030214 - SHD: Zero position passed, loss of calibration 0x030215 - SHD: Invalid characteristic curve, not normalized 0x030216 - SHD: 90% motor temperature threshold exceeded 0x030217 - SHD: Motor operation interrupted by overheating 0x030218 - SHD: Motor does not start due to overvoltage or undervoltage 0x030219 - SHD: Errors in the checksum coding 0x03021C - SHD: Not initialized due to invalid marginal conditions (motor driver) 0x030220 - SHD: System not normalized 0x801A02 - Coding: Control unit is not coded.
Associated Products (13)Associated Documents - February 1, 2014•Document ID: 10147973Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY
- Mfr Comm. #:
- 510714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147972Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147967Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ENGINE
- Mfr Comm. #:
- 122513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryReduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation.
Associated Products (12)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents - January 1, 2014•Document ID: 10147952Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.
Associated Products (90)Associated Documents - January 1, 2014•Document ID: 10147950Service Bulletin/Repair InstructionsVISIBILITY; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147949Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; VISIBILITY
- Mfr Comm. #:
- 640613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?SI B64 06 13 January 2014 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B64 06 13 dated November 2013. designates changes to this revision SUBJECT A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Associated Products (13)Associated Documents - January 1, 2014•Document ID: 10147946Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. CAUSE Software error in TMS 3 (Headlight driver module AHL xenon light)"
Associated Products (38)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents - January 1, 2014•Document ID: 10147943Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; EXTERIOR LIGHTING:FOG LIGHTS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 630214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFog Light Operation Changed After Programming. After the vehicle is programmed with ISTA/P 2.49.x or 2.50.x (integration level earlier than F02013-11-502), the fog lights cannot be operated when the light switch is in the parking light position. Note: The fog light operation has been changed in vehicles produced from March 2013. The fog lights cannot be operated when the light switch is in the park position. This is normal operation due to state legislative requirements that have changed; no further action is required. CAUSE Software error with ISTA/P 2.49.x and 2.50.x
Associated Products (13)Associated Documents - January 1, 2014•Document ID: 10147936Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove Water Drain Plugs from E-Box. The water drain plugs for the left- and right-side E-box may clog. This can lead to water collection/corrosion and allow water to enter the passenger compartment. CAUSE The water drain plug slots are too small.
Associated Products (20)Associated Documents - November 1, 2013•Document ID: 10150193Service Bulletin/Repair InstructionsTIRES
- Mfr Comm. #:
- BMWNOV0613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryService Information bulletin B36 03 13 has been published for the Delivery Stop issued on Wednesday, November 13. The Delivery Stop affects certain 2014 model year F30, F31 and F32 October 2013 production vehicles. Tire Identification numbers (molding number and DOT number) must be checked and if necessary, affected tires replaced. Affected vehicles in center inventory must not be delivered until the tires have been checked. The small number of affected vehicles can be identified via the Key Reader, DCS Inquiry or ISPA with the description: Defect Code 0036820100, Delivery Stop, B36 03 13 Check Tire ID
Associated Products (13)Associated Documents - November 1, 2013•Document ID: 10150187Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT
- Mfr Comm. #:
- 840813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"USB Connection Not Working. One, or both of the scenarios listed below may be encountered: 1. The message ""Device not supported"" is displayed in the CID after connecting a USB device to the USB port using a USB cable. 2. The ""USB option"" in the menu cannot be selected (grayed out), after the vehicle was programmed with ISTA/P 2.50.2, or 2.50.3: I-Level F020-13-07-503, or F020-13-07-505. CAUSE 1. Incompatible USB cable is being used 2. Head Unit Basic software error 1 The following procedure should be performed for ""Situation 1, Cause 1"" listed above: Part A (Steps 1 to 3) 1. Duplicate the issue. 2. Verify that the USB cable which is being used, is the original cable for the device and not an aftermarket cable. 3. If the issue is resolved when using an original USB cable supplied by the manufacturer of the device, do not perform step 4 listed below. No further action is required. Part B (Step 4) 4.If the issue is still present when using the original cable from the device manufacturer, proceed to program and code the vehicle using ISTA/P 2.51.0 or higher. ? I-Level after programming would be F020-13-11-501, or higher. Note that ISTA/P will automatically reprogram and code all programmable control modules that do not have the latest software. For information on programming and coding with ISTA/P, refer to CenterNet / Aftersales Portal / Service / Workshop Technology / Vehicle Programming."
Associated Products (13)Associated Documents - November 1, 2013•Document ID: 10150184Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryA/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Associated Products (13)Associated Documents - November 1, 2013•Document ID: 10150183Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 630713
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryDaytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
Associated Products (41)Associated Documents