BMW 335i Service Bulletins
690 manufacturer communications on file.
- January 1, 2013•Document ID: 10149306Service Bulletin/Repair InstructionsSTRUCTURE:EMERGENCY:ESCAPE/EGRESS/EXIT; EQUIPMENT
- Mfr Comm. #:
- 511011
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryAnti-trap Is Activated when Raising the Front Side Windows. When closing the front side windows using the convertible top switch or the central power window switch, one or both front side windows come to a stop at the top third travel area, and then reverse direction slightly. When the switch is actuated again, the windows will close normally. CAUSE The front side windows contact the rear side windows, causing the anti-trap feature of the front side windows to trigger.
Associated Products (14)Associated Documents - January 1, 2013•Document ID: 10149303Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- 340113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMErroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.
Associated Products (7)Associated Documents - January 1, 2013•Document ID: 10149302Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320112
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryTeile Clearing for Steering Systems.
Associated Products (11)Associated Documents - January 1, 2013•Document ID: 10149299Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 122412
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Engine: DME FC CDA904 FA CAN Message State Trailer 0x2E4 Is Missing.
Associated Products (11)Associated Documents - January 1, 2013•Document ID: 10149298Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE; POWER TRAIN
- Mfr Comm. #:
- 122212
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryService Action: Program Control Units. When coming to a stop, there is the possibility of an unfavorable judder. This is due to the software parameters for downshifting and transmission clutch control. CAUSE Unfavorable vehicle software
Associated Products (10)Associated Documents - January 1, 2013•Document ID: 10149296Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121412
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
Associated Products (26)Associated Documents - January 1, 2013•Document ID: 10149293Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 111012
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary?N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding internally.
Associated Products (41)Associated Documents - December 1, 2012•Document ID: 10150390Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 660712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryRemote Control Key Buttons Operate Incorrectly After Coding. The remote control buttons operate incorrectly after programming and coding using ISTA/P 2.47.x. or later. * Vehicles without option 302 (Alarm System): the 3rd button unlocks the entire vehicle instead of just opening the trunk. * Vehicles with option 302 (Alarm System): the 4th button panic mode siren does not work; the entire vehicle unlocks. CAUSE Front Electronic Module (FEM) coding error
Associated Products (6)Associated Documents - December 1, 2012•Document ID: 10150389Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 652212
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryService Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
Associated Products (70)Associated Documents - December 1, 2012•Document ID: 10150385Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650110
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
Associated Products (106)Associated Documents - December 1, 2012•Document ID: 10150384Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 630612
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Check Control Message ""Adaptive Headlights Failed"". The Check Control message ""Adaptive Headlights Failed"" is displayed in the Central Information Display (CID). All headlights are functioning properly. One or more of the following fault codes are stored in the FEM (Front Electronic Module): * 0x8041BA - Adaptive headlight (AHL): system defective * 0x8041F8 - Right headlight driver module (HDM): AHL error * 0x8041FB - Left headlight driver module (HDM): AHL error CAUSE Software error in the (HDM) Headlight Driver Module"
Associated Products (6)Associated Documents - December 1, 2012•Document ID: 10150381Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610606
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryJunction Box Pin Assignment Change. When replacing the Junction Box (fuse box) using P/N 61 14 6 978 270 or later, note that various pin assignments have changed. The following additional work procedure is necessary to properly perform this repair.
Associated Products (25)Associated Documents - December 1, 2012•Document ID: 10150377Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 340612
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryDSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: DSC ??D36D44 - Signal error longitudinal torque distribution (LMV) ??48097D - Transfer Case clutch position open CAUSE Software calibration error in the LMV
Associated Products (6)Associated Documents - December 1, 2012•Document ID: 10150371Service Bulletin/Repair InstructionsAIR BAGS; LANE DEPARTURE
- Mfr Comm. #:
- 270212
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"DSC Warning Light Is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: ??D36D44 - Signal error longitudinal torque distribution (LMV) ??48097D - Transfer Case clutch position open CAUSE Software calibration error in the LMV"
Associated Products (6)Associated Documents - November 1, 2012•Document ID: 10049679Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- SIB-12-18-12
- Date Added:
- January 18, 2013
- Manufacturer:
- BMW
SummaryBMW: IF BSD COMMUNICATION IS DISRUPTED, OIL LEVEL SENSOR DATA IS NO LONGER RECEIVED BY DME. BSD COMMUNICATION FAULT(S), AFTER REPAIRS ARE SHORTLY SET, REQUIRES REMOVAL OF IGNITION HARNESS FROM CYLINDER HEAD COVER. ALL MODELS. NO MODEL YEARS LISTED. *PE
Associated Products (20)Associated Documents - October 12, 2012•Document ID: 10049439Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- SB-1214
- Date Added:
- January 16, 2013
- Manufacturer:
- BMW
SummaryBMW: VEHICLES NEEDS DIAGNOSING FOR N63 MISFIRE FAULTS WHEN SERVICE ENGINE SOON LAMP IS ILLUMINATED. LACK OF DIAGNOSING ENGINE OR FUEL SYSTEM COULD CAUSE INCORRECT DIAGNOSIS AND REPEATED REPAIR ATTEMPTS. NO MODELS OR MODEL YEARS LISTED. *PE
Associated Products (20)Associated Documents - October 1, 2012•Document ID: 10150334Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 651512
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
Associated Products (70)Associated Documents - October 1, 2012•Document ID: 10150333Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640412
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryBlower Makes an Unusual Noise. An unusual howling noise is heard coming from the glove compartment and passenger foot well area (blower motor). CAUSE Foreign material such as leaves may have entered the blower motor via the fresh air intake.
Associated Products (6)Associated Documents - October 1, 2012•Document ID: 10150332Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:TAIL LIGHTS
- Mfr Comm. #:
- 630512
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryTail Lamp Is Loose in theTrunk Lid. The customer may notice the tail lamp is either loose or protruding outward from the trunk lid. The tail lamp is not attached to the trunk lid properly.
Associated Products (6)Associated Documents - October 1, 2012•Document ID: 10150330Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 611305
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
Associated Products (135)Associated Documents