BMW 325xi Service Bulletins
123 manufacturer communications on file.
- May 1, 2013•Document ID: 10149589Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- 130409
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
Associated Products (120)Associated Documents - March 1, 2013•Document ID: 10150133Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 651310
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIn all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
Associated Products (57)Associated Documents - March 1, 2013•Document ID: 10150131Service Bulletin/Repair InstructionsAIR BAGS:SENSOR:OCCUPANT CLASSIFICATION; AIR BAGS
- Mfr Comm. #:
- 651013
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Enabling and Replacing New OC3 Seat Mat. The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it."
Associated Products (51)Associated Documents - March 1, 2013•Document ID: 10150130Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 651009
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (173)Associated Documents - March 1, 2013•Document ID: 10150099Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- 130213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
Associated Products (118)Associated Documents - March 1, 2013•Document ID: 10150096Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE
- Mfr Comm. #:
- 121611
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
Associated Products (134)Associated Documents - March 1, 2013•Document ID: 10150095Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 110907
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIntermittent Hydraulic Valve Adjuster (HVA) Noise. An occasional ticking or rattling noise from the camshaft hydraulic valve lifters (HVA) may occur during cold engine starts, due to frequent short-distance driving, or the noise may occur for an extended period of time even though the engine is at operating temperature. Improved parts were phased into production beginning on 10/1/2008 and fully implemented on November 31st 2008.
Associated Products (31)Associated Documents - February 1, 2013•Document ID: 10149441Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- 513608
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""B5116_ECSPPL2."""
Associated Products (77)Associated Documents - February 1, 2013•Document ID: 10149431Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340208
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryErroneous Brake Pad Replacement Message. The Dynamic Stability Control module (DSC) calculates the brake pad replacement intervals based on information from the front and rear axle brake pad wear sensors. When replacement of the front and or rear brake pads is necessary, the DSC control module triggers an indicator lamp located in the vehicle's instrument cluster. However, the brake pad indicator lamp may be illuminated although a replacement of the brake pads is not necessary. Additionally, one or both of the following fault codes may be stored in the DSC control module: * 5DE0 Brake-pad wear: plausibility, front axle * 5DE1 Brake-pad wear: plausibility, rear axle CAUSE DSC software error
Associated Products (14)Associated Documents - December 1, 2012•Document ID: 10150385Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650110
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
Associated Products (106)Associated Documents - December 1, 2012•Document ID: 10150381Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610606
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryJunction Box Pin Assignment Change. When replacing the Junction Box (fuse box) using P/N 61 14 6 978 270 or later, note that various pin assignments have changed. The following additional work procedure is necessary to properly perform this repair.
Associated Products (25)Associated Documents - December 1, 2012•Document ID: 10150365Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL
- Mfr Comm. #:
- 122112
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"N51, N52K and N52T: Idle Fluctuation During Engine Warm-up Phase. After a cold engine start, the idle speed may be unstable or start fluctuating up and down slightly while the vehicle is stopped. On vehicles with automatic transmissions, roughness or shuddering may be felt during this warm-up period when diving away slowly in ""D"" or in ""R"" without depressing the accelerator pedal. No relevant errors are stored in the DME fault code memory, and these symptoms are no longer present once the engine is at operating temperature (> 90C). Unfavorable DME software"
Associated Products (28)Associated Documents - October 1, 2012•Document ID: 10150330Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 611305
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
Associated Products (135)Associated Documents - October 1, 2012•Document ID: 10150329Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 513911
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIntermittently the trunk lid does not pop open when using the remote, or latch when closing. If the vehicle is driven and the trunk is not closed fully, a Check Control message will be displayed in the instrument cluster. CAUSE The trunk lid is out of tolerance. When opening or closing the trunk lid, the latch rubs against the striker because of insufficient clearance.
Associated Products (25)Associated Documents - October 1, 2012•Document ID: 10150324Service Bulletin/Repair InstructionsVISIBILITY:GLASS, SIDE/REAR
- Mfr Comm. #:
- 511508
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary?SI B51 15 08 Body Equipment October 2012 Technical Service. This Service Information bulletin supersedes SI B51 15 08 dated July 2008. designates changes to this revision SUBJECT Rear Window False Anti-trap Activation. INFORMATION The anti-trap protection feature may be activated when no obstruction is present. This may occur at either one or both of the rear windows. The root cause of the false anti-trap activation may be difficult to determine. The attached diagnosis flowchart has been developed to assist with determining the actual root cause of the failure as well as to help prevent unnecessary part replacements. The root cause is typically either an issue with the window system, or an electrical/software issue. The diagnosis flowchart will help ensure that repairs are only carried out for the system that is most likely at fault. Refer to B511508_Attachment. PARTS INFORMATION Refer to the Electronic Parts Catalog (EPC) for the appropriate parts noted in the diagnostic flowchart. WARRANTY INFORMATION Not applicable.
Associated Products (30)Associated Documents - August 1, 2010•Document ID: 10037025Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- SIB-63-02-01
- Date Added:
- April 28, 2011
- Manufacturer:
- BMW
SummaryBMW: PROCEDURE FOR DETERMINING AND REPLACING INCANDESCENT AND HALOGEN LIGHT BULBS UNDER WARRANTY. *RM
Associated Products (217)Associated Documents - June 1, 2010•Document ID: 10036979Service Bulletin/Repair InstructionsSTEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING:HYDRAULIC POWER ASSIST SYSTEM
- Mfr Comm. #:
- SIB-32-04-07
- Date Added:
- April 26, 2011
- Manufacturer:
- BMW
SummaryBMW: A NEW TECHNICAL PROCESS HAS BEEN CREATED FOR BMW TO IDENTIFY CAUSES OF STEERING COMPLAINTS WITH A WIDE RANGE OF MODELS. *RM
Associated Products (145)Associated Documents - December 1, 2009•Document ID: 10033130Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- SIB-16-02-09
- Date Added:
- July 14, 2010
- Manufacturer:
- BMW
SummaryBMW VEHICLES: FUEL LEVEL SENSOR REPAIRS. WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE
Associated Products (193)Associated Documents - April 1, 2007•Document ID: 10019998Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE
- Mfr Comm. #:
- 120606
- Date Added:
- May 22, 2006
- Manufacturer:
- BMW
SummaryVOLUNTARY EMISSIONS RECALL 06E-A01: N52 - PROGRAMMING VEHICLE FOR OBD DIAGNOSTIC. MAY CAUSE THE OBD DIAGNOSTIC NOT TO DETECT POTENTIAL MALFUNCTIONS OF VARIOUS EMISSION RELEVANT SENSORS, CONSEQUENTLY, THE SERVICE ENGINE SOON LIGHT WILL NOT ILLUMINATE. *TT
Associated Products (6)Associated Documents - April 1, 2006•Document ID: 10020254Service Bulletin/Repair InstructionsSTEERING:COLUMN
- Mfr Comm. #:
- 320706
- Date Added:
- August 22, 2006
- Manufacturer:
- BMW
SummarySTEERING COLUMN CLICKING NOISE. *TT
Associated Products (6)Associated Documents