Mazda CX-30 Service Bulletins (2021)
606 manufacturer communications on file.
- September 9, 2020•Document ID: 10180715Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- SA-065-20
- Date Added:
- October 5, 2020
- Manufacturer:
- MAZDA
SummarySome customer's may complain that the HVAC system only blows warm to cool air (not cold) after starting the vehicle and not moving right away. This may be caused by a closed Active Air Shutter (AAS). Under specific circumstances, the AAS has a âÂÂlearning issueâ where AAS is kept closed after startup even if the PCM requests it to be open. The shutters will open and work correctly as soon as the vehicle speed exceeds 6.25 MPH (10 KPH). NO DTC will be set when this happens.
Associated Products (2)Associated Documents - September 1, 2020•Document ID: 10180793Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- SA-060-20b
- Date Added:
- October 5, 2020
- Manufacturer:
- MAZDA
SummaryWhen replacing the Body Control Module (BCM) in a 2019 Mazda3, it needs to be configured and the instructions in the Workshop manual on MGSS are incorrect. Use the instructions in the Repair Procedure below to configure the new BCM.
Associated Products (2)Associated Documents - September 1, 2020•Document ID: 10180792Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT
- Mfr Comm. #:
- SA-059-20b
- Date Added:
- October 5, 2020
- Manufacturer:
- MAZDA
SummaryDuring BCM replacement, MDARS may display a Configuration Error warning message. This may be caused by any of the following:ï· Poor internet connection ï· MDARS failureï· Low Battery. Perform the BCM Recovery Procedure below to manually configure the BCM.
Associated Products (2)Associated Documents - August 18, 2020•Document ID: 10179315Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-063-20
- Date Added:
- September 3, 2020
- Manufacturer:
- MAZDA
SummaryWhen performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.
Associated Products (7)Associated Documents - August 13, 2020•Document ID: 10179313Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; FORWARD COLLISION AVOIDANCE; PARKING BRAKE; EQUIPMENT; VISIBILITY
- Mfr Comm. #:
- SA-062-20
- Date Added:
- September 3, 2020
- Manufacturer:
- MAZDA
SummarySome customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ï· The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: ï· The windshield is dirty ï· The FSC lens is foggy ï· There is low visibility due to rain, fog or snow ï· It is at night and there is not enough light ï· There is direct or reflected sunlight on the FSC ï· There is problem with the FSC ï· There is a problem with the AUTOHOLD control function. ï· There is a problem with the electric parking brake (EPB).
Associated Products (2)Associated Documents - July 10, 2020•Document ID: 10177943Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- SA-056-20
- Date Added:
- August 5, 2020
- Manufacturer:
- MAZDA
SummarySome customers or technicians (during PDI) may have concerns with the front doors sticking (especially on hot days) and/or poor appearance, fitment, alignment or gaps with the front and rear door sash molding. These concerns may be related to the door sash molding interference between the front and rear doors.
Associated Products (4)Associated Documents