BMW ActiveHybrid 3 Service Bulletins (2015)
423 manufacturer communications on file.
- May 1, 2014•Document ID: 10148333Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
Associated Products (79)Associated Documents - May 1, 2014•Document ID: 10148323Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK; STRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- 511314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTrunk Lid Does Not Open Completely. The customer may complain that the trunk does not open fully when using the remote key or hands-free trunk-lid opening (a Comfort Access function). CAUSE * A dry trunk lid seal causes the trunk lid to stick. * F30 and F32 only: A trunk return spring that is not installed correctly may not open the trunk lid fully.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148321Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMF56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand. In a continuing effort to maintain the utmost in Motorer satisfaction, MINI USA is offering our dealer partners an alternative solution, the "Make Good" program. For all affected MINI F56 vehicles: * Produced from May 1, 2014 to June 30, 2014 and * Built without the factory order "Contrasting Roof and Mirror Caps" option (382 and 383) Your MINI dealer can offer these Motorers the installation of an accessory roof graphic or set of mirror caps. The Motorer has the choice of either the accessory roof graphic or exterior mirror caps, not both. MINI Area Manager (AM) "Field Authorization" (FAS) is not required. Note: For eligible vehicles (VINs) that are affected by this production restriction, the procedure outlined in this bulletin only applies to mirror caps or roof graphics installed by your dealer. Mirror caps or roof graphics installed through the MINI USA "VIA" (VDC-Installed Accessory) program are not eligible for reimbursement through this Make Good Program.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148312Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE; SUSPENSION:FRONT:WHEEL BEARING
- Mfr Comm. #:
- 310112
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (70)Associated Documents - May 1, 2014•Document ID: 10148308Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (82)Associated Documents - April 1, 2014•Document ID: 10148276Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 650514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTraffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
Associated Products (209)Associated Documents - April 1, 2014•Document ID: 10148273Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (242)Associated Documents - April 1, 2014•Document ID: 10148270Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY:DOOR
- Mfr Comm. #:
- 511014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Door Loudspeaker Make Noises When Cold. The customer complains of front door loudspeaker noises when the temperature is below freezing. CAUSE Water from the door window may enter the rear area of the front door medium range loudspeaker basket/cage and can solidify when the temperature drops below freezing, creating the noise.
Associated Products (24)Associated Documents - April 1, 2014•Document ID: 10148257Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL
- Mfr Comm. #:
- 130114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of ""Incorrect diesel exhaust fluid"" may be displayed with ""no start scenario countdown"" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software"
Associated Products (20)Associated Documents - April 1, 2014•Document ID: 10148254Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
- Mfr Comm. #:
- 120214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Program Control Units (Fuel Shut-off Valve). Due to a software error, it is possible that a Check Engine light (MIL) may not be illuminated after a fault is detected at the fuel shut-off valve (TAV). This is an emissions-relevant fault.
Associated Products (7)Associated Documents - March 1, 2014•Document ID: 10147925Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 630814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryActive Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. CAUSE Broken mounting bolt holding on the rear height sensor bracket
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147980Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147979Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Heating and Air Conditioner. There is an intermittent whirring noise from the IHKA system when the engine is under load between 2,000 and 3,000 rpm, and sometimes at approximately 5,000 rpm. CAUSE Vibrations from the A/C low-pressure hose are resonating into the heating and air conditioning system.
Associated Products (11)Associated Documents - February 1, 2014•Document ID: 10147973Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY
- Mfr Comm. #:
- 510714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147972Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog.
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents - January 1, 2014•Document ID: 10147950Service Bulletin/Repair InstructionsVISIBILITY; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147946Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. CAUSE Software error in TMS 3 (Headlight driver module AHL xenon light)"
Associated Products (38)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents