Audi Q7 Service Bulletins (2010)
865 manufacturer communications on file.
- November 30, 2012•Document ID: 10122837Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- A941299 2029194-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 12-74 dated April 23, 2012 . The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an ? Adaptive Headlight Defective? warning can be present in the cluster if the vehicle has the Prestige trim level. DTCs are set in the 09 ? Central Electric Control Unit or in the 55 ? Headlamp Range Control Unit depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the 09 module. Vehicles with the Prestige option package can have the DTC set in the 55 module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory.
Associated Products (5)Associated Documents - November 30, 2012•Document ID: 10050921Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; EXTERIOR LIGHTING
- Mfr Comm. #:
- TSB-94-12-99
- Date Added:
- February 13, 2013
- Manufacturer:
- AUDI
SummaryAUDI: VEHICLES, FROM MANUFACTURE, ARRIVED WITH HEADLAMPS HOUSING WHERE ONE OR MORE CONNECTORS, FULLY DISCONNECTED OR PARTIALLY DISCONNECTED INSIDE, CAUSING LOW BEAMS TO INTERMITTENTLY FLICKER AND HIGH BEAMS FAILING TO FUNCTION. MODELS 2013 Q7. *PE
Associated Products (4)Associated Documents - November 21, 2012•Document ID: 10065385Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 2028277/4
- Date Added:
- May 19, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (5)Associated Documents - November 21, 2012•Document ID: 10122838Service Bulletin/Repair InstructionsEQUIPMENT; EXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- A941298 2028277-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 12-91 dated October 24, 2012. Considerable moisture present in headlamp. The moisture disappears only after extended drives (greater than 10 minutes). No external damage to headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different ? climate zones? inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. The moisture in the headlamps can be compared with condensation on the windshield, which is cleared by the "defroster vent". This moisture buildup can happen for example: after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion nor does it lead to damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp.
Associated Products (5)Associated Documents - November 16, 2012•Document ID: 10065398Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 23F1
- Date Added:
- May 19, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (1)Associated Documents - November 16, 2012•Document ID: 10065376Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 2012886/6
- Date Added:
- May 19, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (8)Associated Documents - November 16, 2012•Document ID: 10249091Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
- Mfr Comm. #:
- UPDATE23F1
- Date Added:
- January 22, 2024
- Manufacturer:
- AUDI
SummarySVM update and Missing Emblems
Associated Products (1)Associated Documents - November 16, 2012•Document ID: 10122847Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM
- Mfr Comm. #:
- A871236 2012886-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 87 number 10-07 dated September 2, 2010. The A/C system is not cooling as desired in hot weather areas. The following are suggestions to achieve maximum cooling efficiency in hot weather areas.
Associated Products (8)Associated Documents - November 16, 2012•Document ID: 10122810Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT; STRUCTURE
- Mfr Comm. #:
- Update Bulletin
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 23 number 10-05 dated February 26, 2010. The ?TDI? and rear ?quattro? emblems are missing from the lower right corner of the rear lid. MIL on. DTC P229F or P2201 (NOx Sensor Circuit Range/Performance) stored in ECM. Procedure is valid only for vehicles that show the 23F1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the Limited New Vehicle Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. The work instructions for installing the ?TDI? and rear ?quattro? emblems during assembly were removed for a short production run. Software update needed.
Associated Products (1)Associated Documents - November 1, 2012•Document ID: 10122840Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM; EQUIPMENT
- Mfr Comm. #:
- A941296 2027773-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. For vehicles with halogen DRLs, please reference TSB 2017488, 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.
Associated Products (40)Associated Documents - October 29, 2012•Document ID: 10250473Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:SUPPLY:COMPRESSOR; UNKNOWN OR OTHER
- Mfr Comm. #:
- 4312112018765
- Date Added:
- February 20, 2024
- Manufacturer:
- AUDI
SummarySelf-leveling compressor inoperative
Associated Products (22)Associated Documents - October 29, 2012•Document ID: 10122788Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- A431211 2018765-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 43 number 12-08 dated February 2, 2012. The self-leveling system cannot be adjusted any more with the MMI. The compressor for the self-leveling system continues to run after switching off the engine and locking the vehicle. DTCs may be stored. Because of poor performance or failure of the compressor for air suspension, the vehicle position cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected.
Associated Products (22)Associated Documents - October 29, 2012•Document ID: 10047699Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- TSB-43-12-11
- Date Added:
- December 5, 2012
- Manufacturer:
- AUDI
SummaryAUDI: THE CONTROL MODULE, AS A SAFEGUARD, WILL LOWER VEHICLE TO LOWEST POSITION AND ILLUMINATE WARNING LIGHT DUE TO FAILURE OF COMPRESSOR, FOR AIR SUSPENSION OR POOR PERFORMANCE, VEHICLE NOT ABLE TO BE ADJUSTED. MODELS 2004-2008 A6 (C6), 2013 A6 (C7); 2004-2013 A8 (D3-D4); 2013 A7 (C7); 2007-2011 Q7. *PE
Associated Products (23)Associated Documents - October 26, 2012•Document ID: 10067429Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULE
- Mfr Comm. #:
- SB-2031413/1
- Date Added:
- May 23, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (15)Associated Documents - October 26, 2012•Document ID: 10122777Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEATS
- Mfr Comm. #:
- A571278 2031413-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummaryThe seat memory does not work. The MMI displays that the memory function is not active. The seat memory control unit can be deactivated due to voltage fluctuations in the vehicle? s power system, or from a large static discharge through the seat cover. If the seat memory control unit is deactivated due to the above mentioned influences, the control unit cannot be reactivated through any vehicle controls, vehicle keys, or through the normal GFF test plans. It can only be reactivated with special test plans within the tester.
Associated Products (15)Associated Documents - October 26, 2012•Document ID: 10122776Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT
- Mfr Comm. #:
- A571279 2018737-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 57 number 10-32 dated September 9, 2010. Customer may complain that the vehicle locks itself when removing the key from the ignition lock. When removing the ignition key from the ignition, the customer may unintentionally operate the lock button of the remote key. With the S contact in the ignition lock off (key is removed), the central locking will resume to respond to signals from the remote key. MVB 17 in electric control unit address $46 (Comfort System Central Control Module) can be used for argumentation. The last received central locking command is stored in this MVB. A value of ?2? indicates a locking command last sent from the remote key. With the Autolock feature, MVB 17 is overwritten. Therefore MVB 17 must be read immediately after the complaint.
Associated Products (15)Associated Documents - October 25, 2012•Document ID: 10063896Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- SB-2031367/1
- Date Added:
- May 9, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (7)Associated Documents - October 25, 2012•Document ID: 10122770Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT
- Mfr Comm. #:
- A911264 2031367-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummaryCD or DVD disks do not automatically change from one to the next in the external CD or DVD changer. The CD and DVD changer have different operating concepts. MMI3G: Disks in the CD changer are always automatically changed from one to the next. MMI3G+ (with Audi connect): Disks in the CD changer are automatically changed from one to the next, but this operation is disabled when the Repeat option is turned on in the Media Settings menu. By default (MMI factory default setting) the repeat option is set to ? Off?. DVD changer (A8 only): Disks in the DVD changer can only be changed manually.
Associated Products (7)Associated Documents - October 24, 2012•Document ID: 10067463Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES
- Mfr Comm. #:
- SB-2028277/3
- Date Added:
- May 23, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - October 24, 2012•Document ID: 10122767Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- A941291 2028277-
- Date Added:
- November 8, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 12-68 dated March 1, 2012. Considerable moisture present in headlamp. The moisture disappears only after extended drives (greater than 10 minutes). No external damage to headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different ? climate zones? inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. The moisture in the headlamps can be compared with condensation on the windshield, which is cleared by the "defroster vent". This moisture buildup can happen for example: after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion nor does it lead to damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp.
Associated Products (3)Associated Documents