Audi Q5 Service Bulletins (2015)
1,111 manufacturer communications on file.
- May 8, 2015•Document ID: 10120043Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- A911583 2030465-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814. This bulletin only applies to vehicles with MMI3G+ Navigation (PR Number "7T6") and to vehicles with MMI3G+ Navigation, but without Audi Connect (PR Number "7T6" with additional PR code of "PND"). Continual improvements to MMI software provides solutions to issues experienced in the field.
Associated Products (75)Associated Documents - May 7, 2015•Document ID: 10120039Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- A661553 2038652-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 66 number 15-45 dated January 20, 2015. The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
Associated Products (9)Associated Documents - May 6, 2015•Document ID: 10120032Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- A201545 2035073-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 20 number 14-43 dated December 19, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
Associated Products (23)Associated Documents - May 1, 2015•Document ID: 10120049Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD WIPER/WASHER
- Mfr Comm. #:
- A921510 2038151-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
Associated Products (63)Associated Documents - April 30, 2015•Document ID: 10119997Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- A661552 2035673-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 66 number 15-50 dated April 10, 2015. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
Associated Products (16)Associated Documents - April 29, 2015•Document ID: 10119985Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- A011521 2040508-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummaryThe MIL is on. DTC P046100 is stored in the ECM. DTC P046100 can be caused by miscalculations within the ECM software.
Associated Products (14)Associated Documents - April 28, 2015•Document ID: 10119990Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- A391515 2028902-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold (normally below freezing) and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
Associated Products (38)Associated Documents - April 24, 2015•Document ID: 10120002Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; BACK OVER PREVENTION: CAMERA SYSTEM
- Mfr Comm. #:
- A911582 2029903-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.
Associated Products (140)Associated Documents - April 23, 2015•Document ID: 10119993Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- A461510 2040134-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummaryCustomer reports hearing a squeal noise from the front brakes during first brake application in the morning, with cold brakes, below 20 mph, below 40ºF, and high humidity.
Associated Products (2)Associated Documents - April 23, 2015•Document ID: 10119992Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- A461509 2040133-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummaryCustomer reports hearing a squeal noise from the front brakes during first brake application in the morning, with cold brakes, below 20 mph, below 40ºF, and high humidity.
Associated Products (1)Associated Documents - April 17, 2015•Document ID: 10120004Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS:SWITCH
- Mfr Comm. #:
- A941566 2017566-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision.
Associated Products (42)Associated Documents - April 17, 2015•Document ID: 10120003Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- A941565 2012749-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
Associated Products (200)Associated Documents - April 14, 2015•Document ID: 10119981Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- A001574 2031122-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 00 number 15-71 dated January 9, 2015. A repair authorization must be obtained if a Q5 hybrid arrives at an Audi dealership and requires diagnosis or repair for any of the following concerns. A Technical Assistance Center (TAC) ticket must be created before starting the repairs on the traction motor, power electronics, high voltage battery, high voltage cables, high voltage A/C compressor, auxiliary batter, and/or any hybrid warning messages in the instrument cluster. Prior authorization or a Technical Assistance Center (TAC) ticket is not required for repairs provided in any applicable TSB or RVU, for routine maintenance, for PDI, or for repairs on components and concerns not listed above.
Associated Products (4)Associated Documents - April 10, 2015•Document ID: 10119996Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- A661551 2026997-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 66 number 15-48 dated March 16, 2015. Customer may report hearing wind noise from the front door area. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise.
Associated Products (4)Associated Documents - April 10, 2015•Document ID: 10119995Service Bulletin/Repair InstructionsVISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; STRUCTURE:BODY
- Mfr Comm. #:
- A661550 2035673-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 66 number 13-39 dated December 9, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
Associated Products (16)Associated Documents - April 10, 2015•Document ID: 10119988Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN
- Mfr Comm. #:
- A191558 2036852-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummaryCooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
Associated Products (18)Associated Documents - April 2, 2015•Document ID: 10120007Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; VISIBILITY:REAR WINDOW WIPER/WASHER:MOTOR
- Mfr Comm. #:
- A971546 2040221-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummaryThe rear wiper is not functioning or only functions intermittently. Corrosion at the B538 splice of the rear wiper motor control circuit can cause an excessive voltage drop, resulting in an out of range control signal.
Associated Products (6)Associated Documents - March 24, 2015•Document ID: 10120679Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- A661549 2030471-
- Date Added:
- October 25, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate-length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
Associated Products (66)Associated Documents - March 20, 2015•Document ID: 10119957Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- A911580 2036575-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. This profile will be used each time the voice recognition system is used without a phone being paired to the MMI. This TSB is informational only and not applicable to any Audi warranty.
Associated Products (37)Associated Documents - March 20, 2015•Document ID: 10119956Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- A911579 2038824-
- Date Added:
- October 21, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
Associated Products (207)Associated Documents