Jeep Gladiator Complaints (2021)

292 consumer complaints on file.

#11743537June 11, 2026
POWER TRAIN
Engine light came on, vehicle went into limp mode. Transmission would not shift any higher than 3rd gear and kept slipping while on interstate! Was almost hit by several 18 wheelers! Jeep dealership said our vin is not part of the service bulletin but they did get the P0733 code! Make it make sense! I guess we’re supposed to get run over by 18 wheelers before they’ll fix it!
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11743517June 11, 2026
STEERING
The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 26V363000 (Steering); however, the parts required for the recall repair were unavailable. The dealer was contacted, and it was confirmed that the parts were not available. The contact stated the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11742573June 7, 2026
FUEL/PROPULSION SYSTEM, UNKNOWN OR OTHER
Every time I fill up my gas tank, the fuel doesn’t shut off in time from the pump and gas comes backward up the filler neck, onto the side of my jeep.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11741018May 30, 2026
POWER TRAIN
There was a recall for the clutch. I took it to the dealer (Autonation Jeep in Santa Clarita, CA). Ever since then, there is an intermittent, non-reproducible grinding and clicking (sound and feeling through the pedal) in the clutch (like a loose piece/nut is bouncing around and clanking and grinding against the clutch). The clutch pedal is also more spongy, catching only about halfway down, and sometimes feeling like at full depression it is not entirely engaged. I have taken it back to the dealer twice, and both times they will not work on it because they cannot hear or reproduce the feel/sound. The sponginess of the clutch is subjective, they say, and their opinion is that it feels fine.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11739847May 25, 2026
POWER TRAIN
I recently experienced significant transmission issues, specifically hard engage in reverse (cold), and failure to shift higher than 3rd gear. The rear axle is leaking and the front axle is shaking. My jeep has the P0733 code for the D-clutch failure confirmed at a Jeep dealership, along with the steering damper Campaign XF1 and the Dana M220 axle (TSB 03-001-23) and should be included in these TSB’s/CSN’s/Campaigns! It is currently sitting at the Jeep Dealership in Covington, La unable to be driven needing $9790 worth of repairs from all of these and I’ve barely had it a year! I am so disappointed in Jeep
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11739011May 20, 2026
POWER TRAIN
Last year I received a message, letter and perhaps an email related to my jeep and recall for the clutch plate assembly. The recall was performed twice because first was incorrect. Transmission had to be replaced a few weeks later. Since then, I've had numerous visits to dealership, and had several incidents this week traveling across country to clear "Service Transmission messages: on the display, and two incidents where the jeep went into "limp mode" at high speeds. Four more stops have not fixed the problem. Now I am at a place who has found that the transmission was not installed properly, the software wasn't properly flashed and things were left hanging (connectors and cables) without being properly secured. The transmission was replaced under warranty, which has run out, but these messages have been appearing since the original recall. Now, I am going to have to pay a large fee (over 3000 dollars) to get Jeep back. Plus paying 100 to another dealership in Kansas to have them look at the jeep without a remedy. (See:Jeep Recall 19A / NHTSA Campaign 23V116, NHTSA Recall 24V-572, NHTSA Recall 21V-028 / Jeep Recall Y01 ) - my Jeep is listed as "0 recalls" but the dealership has not reported any work on my vehicle to CarFax. The repair shop is working with me to collect evidence (Photos, documentation, and data about the Jeep's issues. ALL of this began immediately after the first recall last year, and these problems have not been remedied, and the Jeep has become dangerous when on the highway. (Limp mode multiple times: 17 Feb2026, 13 May 26, 13 May 26 all at highway speeds). This should have been covered under warranty, and I should not be subjected to "No repair" because a dealership "Doesn't see a problem" - the computer doesn't keep any codes for these incidents, thus they will not dig into the problem, and now warranty has expired so they can charge whatever they wish.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11734098April 27, 2026
ELECTRICAL SYSTEM
Complete failure and shut down of all systems while driving through an intersection. Result found by dealer: Frayed wiring harness on right side of engine rubbing near exhaust parts. Known problem in several models of Jeep due to TBS issued to dealers. Jeep failed in intersection in [XXX] and was able to coast to curb. Started later and was able to drive it back to Prescott, AZ with fingers crossed, took to York Jeep dealer for repairs. They have the repair file. Was 6 mos out of warranty but only about 12k miles ref: Case Number: XXX Release Date: 1/16/2021 Symptom/Vehicle Issue: Check Engine Light On, Service Shifter Message, No Crank No Start. Transmission Wiring Harness Chaffed Or Pinched Near Exhaust DPF Discussion: Initial complaint is that the Check Engine Light is illuminated, Service Shifter Message is displayed, and/or a crank no start condition exists. Upon scanning the vehicle for DTC’s you may find one or more of the following: P2453, P2454, P0335, P0336, P242B, P242C, U0074, U11C3. Diagnosis: Inspect the wiring harness near connector XY230A leading down to the transmission. The harness routing may allow the wiring to make contact with the sharp edge of the DPF gasket flange. It has also been found that the wiring harness could be routed close to the exhaust causing chaffing. Both of these situations could result in damage to the harness and a potential open or short. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11733718April 25, 2026
ELECTRICAL SYSTEM
Rear view camera works only when vehicle is cold, usually only in the morning. I cant use this safety feature whenever I drive the car the rest of the day . I have been in situations driving the truck in off road conditions were the camera is a must to see where I am going, and have been in very dangerous situations getting too close to rocks or deep drops due to lack of rear visibility. And mirrors don't help in some of these situations, because the danger has been completely in the center of the rear of the truck, and out of mirror reach.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11732127April 18, 2026
AIR BAGS
On 12-13-23 I hit an 8 point buck going 55mph head on between the 2 headlights doing 15k in damage.. airbags did not deploy. On 4-11-26 I was hit by a drunk driver head on. I was going 33mph, he was going much faster in a Polaris rzr hit me on the driver side tearing off my tire, and whole suspension completely, sending me into an embankment... and still no airbags deployed.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725933March 20, 2026
FUEL/PROPULSION SYSTEM
Bought this vehicle with 27,000 miles on it. While driving on the interstate with heavy traffic. (Doing Highway speeds) All the sudden the power plant shuts down. It happend at 27,500 miles and happened again at 37,000 miles. It has done it to me four times now. Twice with heavy semi trucks bearing down on me and my family. This was a very UNSAFE situation. The Fault on the screen comes up momentarily and states "Capture Throttle Body Fault." and all power is lost to the throttle. SERIOUS SAFTETY ISSUE. as loosing power on the interstate at 75 miles an hour. I believe JEEP the company should fix this issue as I know for a fact I am not the only individual experincing this problem! Please feel free to reach out to me if you need further information. There was not a crash,fire or injury due to the ability to get off the road and into the apron of the interstate. In a higher traffic location this could be catistrophic. PLEASE PLEASE PLEASE talk this issue seriously as I am convinced this has caused others to wreak. Thanks and have a great day
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11724739March 16, 2026
ELECTRICAL SYSTEM
The contact owns a 2021 Jeep Gladiator. The contact stated that the instrument panel was blank at startup. Due to the failure, the speedometer, fuel gauge, mileage, and other features were not visible. Upon investigation, the contact discovered NHTSA Campaign Number: 24V652000 (Electrical System); which was associated with the failure. A dealer was notified of the failure, and the contact was informed that the vehicle was not included in the recall. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 49,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11723578March 11, 2026
SEAT BELTS
Description of the Safety Issue I am submitting this complaint to report a serious seat belt safety incident involving entrapment and inability to self‑release, which required emergency intervention. While parked, my daughter as a passenger in my Jeep Gladiator, became tangled in the seat belt in such a way that she was physically unable to release herself or exit the vehicle. Despite multiple attempts, the seat belt could not be disengaged, and the situation escalated to the point where I had to cut the seat belt to free her. This was not caused by a crash, sudden stop, or misuse. The seat belt’s configuration, retraction behavior, or release mechanism appeared to contribute to the entrapment and prevented normal occupant egress. Why This Is a Safety Concern Seat belts are intended to protect occupants and allow safe release when needed. In this incident, the seat belt instead: -Entrapped a child occupant -Prevented self‑release -Created a situation where cutting the belt was the only way to avoid further harm Had this occurred during an emergency (fire, water submersion, post‑collision scenario), the inability to quickly exit the vehicle could have resulted in serious injury or worse. Outcome of the Incident -No collision occurred. -No vehicle warning lights or alerts were present. -The seat belt was rendered unusable only because it had to be cut as an emergency safety measure. -The incident caused significant distress and created an immediate safety hazard. Request for Review I am requesting that NHTSA: -Review this incident as a potential seat belt design or functional defect -Consider whether similar incidents may be occurring but underreported -Evaluate whether this issue warrants further investigation, service bulletin, or recall activity Seat belts should never place occupants—especially children—into situations where escape is difficult or impossible.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11718716February 18, 2026
POWER TRAIN
Passenger side rear axle leaking gear oil. Issued was repaired by dealership No warning I just saw the oil on the tire and in my driveway
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11718714February 18, 2026
EXTERIOR LIGHTING
The 3rd brake light in the tailgate malfunctioned This is required to pass New York State safety inspection A Jeep dealer replaced the part No warning on the dashboard of this light failing
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11717851February 13, 2026
STEERING
While angling into a turn lane, I was forced to go back into lane of traffic first signaling into the turn lane (left) then out (right) turn signal seemed to get stuck on, Steering wheel became locked and would only move a fraction of an inch either left or right. Once I was around the obstruction in the turn lane I angled back into it and was able to come to a stop. Once stopped the turn signal very loudly clicked off and the wheel was once again able to be actually turned. The ESS was disabled the whole time and at no point did the vehicle cease to be on and engine running.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11717839February 13, 2026
ELECTRICAL SYSTEM, STEERING, VISIBILITY/WIPER
Two of the same faults occurred within the same month of each other. The first: while driving home from work on the highway, while heavily raining, without warning every alarm light possible engaged, windshield wipers went full speed, vehicle would not shift, and my steering locked up (not to be confused with lost power steering). After about a mile I was able to encourage the Jeep off the side of the highway. While waiting for my tow, with the E Brake set and in Park, the Jeep kept trying to crawl forward on its own. I was unable to turn the vehicle off as it would not respond, in addition to an alarm warning saying not to turn off the Jeep. The second occurrence was in the parking garage at work; I pulled through the parking stall, put the Jeep in reverse to back up and the same fault took place. No steering, wipers on full speed, every alarm on the dash was engaged. Thankfully I was not a highway speed. I was able to turn off the Jeep this time after about 5 minutes of attempting to.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11717367February 11, 2026
EXTERIOR LIGHTING
The center high mounted tail light (CHMTL) has failed. It makes it a little harder to see the vehicle is braking. The fuses are fine. It is a very common failure on Jeep Gladiators. Many times people don't know it has failed. There are no warning lamps or indicators to tell you it has failed.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11716670February 9, 2026
UNKNOWN OR OTHER
I have had my gorilla glass replaced two years ago for cracking on its on, my front windshield cracked again 2 weeks ago for no reason and it cracked in the same location, causing a huge crack along my vison. This glass is supposed to be unbreakable and yet it broke twice since ownership all by it self. No rock chips or anything. I was just sitting at a traffic light when I heard a ting and the crack just grew before my eyes. Bad glass and Mopar knows its a flaw but will not replace it.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11716509February 7, 2026
STEERING
This afternoon I was driving on a 35mph 4 lane road when my power steering suddenly went out. Because it was unusually light traffic and there are no turns or curves, I was able to safely maintain my lane until the power steering resumed just as quickly as it went out. Most women struggle with manually steering a normal sized car- a truck this heavy is nearly impossible. Had I been going any faster or if I were on a curve, I would have absolutely wrecked. There were no alarms, no signals no messages, nothing. Because this Judy happened, I have not yet had it looked at my a mechanic.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11716027February 5, 2026
STEERING
My name is [XXX] , and I am writing to formally submit a complaint regarding the loss of my vehicle due to engine fire. The vehicle was a 2021 Jeep Gladiator Rubicon, VIN [XXX] , with approximately 26,666 miles at the time of loss. I purchased the vehicle on May 13, 2021. The fire occurred on July 10, 2025. I was driving on the freeway, and my vehicle lost power and dashboard warning lights illuminated. When I pulled over, the engine was on fire. The fire department came and doused the flames but my entire engine was destroyed. After the fire, I retained legal counsel and initiated an independent investigation through Fire Cause Analysis in Berkeley, California. Their findings identified the origin of the fire as being linked to the power steering pump electrical connector. I later discovered that NHTSA has an open investigation identified as PE24024 concerning Jeep Gladiator engine fires which notes that the fires reported to NHTSA for this vehicle originated at the power steering pump electrical connector - coinciding with the finding of Fire Cause Analysis. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
Yes
Injuries:
0
Deaths:
0

← Back to Jeep Gladiator