Ford Bronco Service Bulletins (2021)
324 manufacturer communications on file.
- September 20, 2022•Document ID: 10222195Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:ANTILOCK
- Mfr Comm. #:
- TSB 22-2360
- Date Added:
- September 30, 2022
- Manufacturer:
- FORD
SummaryThis article supersedes TSB 22-2210 to update the expected release date of the revised ABS module software. Customers who neutral (4-wheel flat) tow 2021-2022 Broncos equipped with an electronic brake booster (EBB) may report an inconsistent brake assist when a supplemental braking system has been installed. This may result from supplemental brake system set-up that does not account for the Broncos EBB system entering sleep mode (via the ABS module) after a pre-determined period of time following vehicle shut-down. This functionality is necessary to prevent battery drain. Enhanced software is under development to address this condition when the vehicle enters Neutral Tow mode. The new software is expected to be available in December 2022. Monitor OASIS for updates. Until the software becomes available, customers who meet this criteria may perform the procedures below to address this condition when neutral (4-wheel flat) towing their vehicle.
Associated Products (2)Associated Documents - September 19, 2022•Document ID: 10222458Service Bulletin/Repair InstructionsSTRUCTURE:BODY:ROOF AND PILLARS
- Mfr Comm. #:
- 21B49 S2
- Date Added:
- October 5, 2022
- Manufacturer:
- FORD
SummaryCertain 2021 Model Year Bronco Vehicles Equipped with a Hard Top Roof Panel Delamination Program Terms - Updated to extend the program 1 additional year providing the vehicle is still within base warranty mileage limits. Owner Notifications - Revised owner letters
Associated Products (1)Associated Documents - September 16, 2022•Document ID: 10222469Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 22H05
- Date Added:
- October 5, 2022
- Manufacturer:
- FORD
SummaryHarvest/Inspection Program Certain 2021 Model Year 5 Door Bronco Vehicles Side Impact Sensor Retaining Stud and Nut Inspection This program is a proactive investigation by Ford Motor Company to inspect for the correct installation of a side impact crash sensor. Specifically, Ford is investigating whether the right hand and/or left hand side impact sensor could be missing the retaining stud and nut that secure the sensor to the b-pillar of the vehicle. Ford is voluntarily conducting this program because it received one report that a side impact sensor was not installed correctly, and it is inspecting other vehicles that were built around the same time. It is very important that the information and pictures from these inspections be provided to Ford for this study
Associated Products (1)Associated Documents - September 15, 2022•Document ID: 10220384Service Bulletin/Repair InstructionsELECTRONIC STABILITY CONTROL (ESC); SERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- TSB 22-2354
- Date Added:
- September 23, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an illuminated anti-lock brake system (ABS) indicator and stability-traction control indicator, and diagnostic trouble code (DTC) C1013:09 stored in the ABS module. This may be due to ABS module software. To correct the condition, follow the Service Procedure to update the ABS module software.
Associated Products (2)Associated Documents - September 15, 2022•Document ID: 10220383Service Bulletin/Repair InstructionsPARKING BRAKE
- Mfr Comm. #:
- TSB 22-2353
- Date Added:
- September 23, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit multiple error messages displayed in the IPC followed by automatic engagement of the parking brake immediately after starting the vehicle with the doors removed or after sitting in the vehicle for an extended period of time with the vehicle off. This may be due to the software within the anti-lock brake (ABS) module. To correct the condition, follow the Service Procedure to reprogram the ABS module.
Associated Products (2)Associated Documents - August 31, 2022•Document ID: 10218910Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE
- Mfr Comm. #:
- OTASU3 P1 Bronco
- Date Added:
- September 1, 2022
- Manufacturer:
- FORD
SummarySoftware Update 3 Part 1 for 2021-2022 Model Year Bronco vehicles is now available. Quality Improvements Include: Fix for low power mode rearview camera distortion when the vehicle is shut off and restarted quickly.
Associated Products (2)Associated Documents - August 15, 2022•Document ID: 10218629Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- TSB 22-2325
- Date Added:
- August 23, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with a stabilizer bar disconnect system may exhibit an illuminated red and/or amber stabilizer bar disconnect indicator and diagnostic trouble code (DTC) C103A:74 stored in the chassis control module (CHCM). This may be due to the software in the CHCM. To correct the condition, follow the Service Procedure to reprogram the CHCM.
Associated Products (2)Associated Documents - August 11, 2022•Document ID: 10217841Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- SSM 51014
- Date Added:
- August 15, 2022
- Manufacturer:
- FORD
SummaryThe electronic parts catalog for the 2021-2022 Bronco equipped with a 2.7L GTDI engine had the incorrect engine oil dipstick assigned. This problem only existed for a few months and has since been corrected. The incorrect dipstick that showed in the catalog was SPN: MB3Z-6750-B/F (EPN: MB3E-6750-BB/BC). The 'MB3Z' dipstick (EPN: 'MB3E') is ONLY designed for use on the 2022 Bronco Raptor which is equipped with a 3.0L GTDI engine. The correct engine oil dipstick for the 2021-2022 Bronco 2.7L GTDI engine is SPN: FT4Z-6750-B/C (EPN: FT4E-6750-BF/BG).
Associated Products (2)Associated Documents - August 1, 2022•Document ID: 10217830Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- SSM 50982
- Date Added:
- August 15, 2022
- Manufacturer:
- FORD
SummarySome 2018-2022 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit one of the following if the customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.
Associated Products (41)2021 Ford Bronco2021 Ford Bronco Sport2021 Ford Edge2021 Ford Escape2021 Ford Expedition2021 Ford Explorer2021 Ford F-1502021 Ford F-2502021 Ford F-3502021 Ford F-4502021 Ford F-5502021 Ford Mustang Mach-E2021 Ford Transit Connect2021 Lincoln Aviator2021 Lincoln Corsair2021 Lincoln Nautilus2021 Lincoln Navigator2020 Ford Edge2020 Ford Escape2020 Ford Expedition+ 21 moreAssociated Documents - July 29, 2022•Document ID: 10217028Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 50975
- Date Added:
- August 2, 2022
- Manufacturer:
- LINCOLN
SummarySome 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
Associated Products (119)2022 Ford Bronco2022 Ford Bronco Sport2022 Ford Edge2022 Ford Expedition2022 Ford Explorer2022 Ford F-1502022 Ford F-2502022 Ford F-3502022 Ford F-4502022 Ford GT2022 Ford Maverick2022 Ford Mustang2022 Ford Mustang Mach-E2022 Ford Ranger2022 Lincoln Aviator2022 Lincoln Corsair2022 Lincoln Nautilus2022 Lincoln Navigator2021 Ford Bronco2021 Ford Bronco Sport+ 99 moreAssociated Documents - July 22, 2022•Document ID: 10216465Service Bulletin/Repair InstructionsVISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- TSB 22-2297
- Date Added:
- July 28, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with base exterior mirrors (does not have integrated puddle lamps and/or turn signal lamps) may have a whistle noise that originates from the left exterior mirror. This may be due to the design of the exterior mirror cover. To correct this condition, follow the Service Procedure to replace both the left and right exterior mirror covers.
Associated Products (2)Associated Documents - July 22, 2022•Document ID: 10216464Service Bulletin/Repair InstructionsSTRUCTURE:BODY:ROOF AND PILLARS
- Mfr Comm. #:
- TSB 22-2296
- Date Added:
- July 28, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with a factory soft top roof may experience excessive wind noise while driving, loose soft top cover, and/or difficulty latching. This may be due incorrect soft top assembly installation, latch striker positioning and/or a failed soft top component. To correct the conditions, follow the Service Procedure to inspect the vehicle and adjust the soft top components as necessary.
Associated Products (2)Associated Documents - July 21, 2022•Document ID: 10216460Service Bulletin/Repair InstructionsSTRUCTURE:BODY:ROOF AND PILLARS
- Mfr Comm. #:
- TSB 22-2288
- Date Added:
- July 28, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with a hard top roof may exhibit symptoms from the front roof panels that sit at an uneven height which may result in a poor appearance, excessive wind noise, water leaks and/or difficulty latching. This may be due to incorrect vertical adjustment of the front roof panel latch strikers. To correct this condition, follow the Service Procedure to adjust the front panel latch strikers.
Associated Products (2)Associated Documents - July 20, 2022•Document ID: 10216539Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- SSM 50951
- Date Added:
- July 29, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with an EBB may exhibit multiple error messages displayed in the IPC followed by automatic engagement of the parking brake immediately after starting the vehicle with the doors removed or after sitting in the vehicle for an extended period of time with the vehicle off. The issue will resolve itself once the brake pedal is no longer depressed or the parking brake is manually disengaged. This may be due to the software within the anti-lock brake (ABS) module. This issue can be avoided by placing the vehicle in accessory mode for a few seconds before starting the engine. Engineering is working on improved software to correct this condition that will be available in November 2022. No repairs should be made in attempt to correct this condition. Monitor OASIS for updates.
Associated Products (2)Associated Documents - June 29, 2022•Document ID: 10214880Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE; SERVICE BRAKES
- Mfr Comm. #:
- TSB 22-2255
- Date Added:
- July 1, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles built on or before 14-Mar-2022 and equipped with a 2.7L engine may exhibit the inability to disable the traction control system using the traction control on/off switch located on the instrument panel. This may be due to the software within the anti-lock brake system (ABS) module. To correct the condition, follow the Service Procedure and update the ABS software.
Associated Products (2)Associated Documents - June 21, 2022•Document ID: 10214865Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE
- Mfr Comm. #:
- 22B08-S1
- Date Added:
- July 1, 2022
- Manufacturer:
- LINCOLN
SummaryCertain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles Electronic Control Module Recovery: In some of the affected vehicles, an internal error in the Accessory Protocol Interface Module (APIM) or Telematics Control Unit (TCU) module software will prevent the receipt of software updates or enhancements for these modules Ford Power-Up or Lincoln Way. The module will operate as intended otherwise.
Associated Products (5)Associated Documents - June 21, 2022•Document ID: 10214828Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 50871
- Date Added:
- June 30, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles may exhibit a Cross Traffic System/Blind Spot System Fault in instrument panel cluster (IPC). If these symptoms are encountered, inspect the wiring under the rear bumper for chaffing of the 13A409 harness close to connector C4369. If this is determined to be the cause of the issue, refer to Wiring Diagram Cell 005 for wiring repair. If no wiring issues are found, continue with normal diagnostics in Workshop Manual (WSM), Section 419-04.
Associated Products (2)Associated Documents - June 8, 2022•Document ID: 10214159Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- SSM 50842
- Date Added:
- June 17, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles may exhibit a condition of intermittent headlamp operation while the vehicle is OFF and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. Switch and/or module replacement will not resolve this condition. Headlamp operation is not affected while the vehicle is ON. A new headlamp switch is currently under development to correct this condition. Let the customer know they can continue to drive the vehicle and schedule a follow-up appointment in October 2022, when parts are expected to become available. Follow up with the customer to confirm the appointment once OASIS is updated with the repair information.
Associated Products (2)Associated Documents - June 6, 2022•Document ID: 10213708Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- SSM 50829
- Date Added:
- June 17, 2022
- Manufacturer:
- FORD
Summary2021-2022 various Ford and Lincoln vehicles may exhibit an erroneous diagnostic trouble code (DTC) U1A01:93 stored in the telematics control unit (TCU). This may be due to various software parameters within the TCU. If this DTC is identified during normal diagnostics, but the vehicle does not exhibit any customer concerns around the TCU operation, clear this DTC and no further repairs are recommended. If the DTC returns after being cleared or if the vehicle exhibits connectivity concerns with the TCU, continue with normal Workshop Manual (WSM) diagnostics. If set erroneously, this DTC does not cause any observable concerns or warning messages and does not affect vehicle performance or durability. Ford is developing a software update which will be delivered to the vehicle via an over-the-air (OTA) TCU update in July 2022 to prevent this DTC from setting erroneously.
Associated Products (18)2022 Ford Bronco2022 Ford Edge2022 Ford Expedition2022 Ford F-1502022 Ford F-2502022 Ford F-3502022 Ford F-4502022 Ford F-5502022 Ford Mustang Mach-E2022 Ford Transit2022 Lincoln Nautilus2022 Lincoln Navigator2021 Ford Bronco2021 Ford Edge2021 Ford F-1502021 Ford Mustang Mach-E2021 Lincoln Nautilus2007 Lincoln MKXAssociated Documents - June 1, 2022•Document ID: 10214121Service Bulletin/Repair InstructionsVISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- TSB 22-2215
- Date Added:
- June 13, 2022
- Manufacturer:
- FORD
SummarySome 2021-2022 Bronco vehicles equipped with base exterior mirrors (does not have integrated puddle lamps and/or turn signal lamps) may have a whistle noise that originates from the left exterior mirror. This may be due to the design of the exterior mirror cover. To correct this condition, follow the Service Procedure to replace both the left and right exterior mirror covers.
Associated Products (2)Associated Documents