BMW M760Li Service Bulletins (2017)
96 manufacturer communications on file.
- February 1, 2017•Document ID: 10146532Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; ENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B122716
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"? DIAGNOSING NON FUNCTIONING ""eDRIVE"" This Service Information bulletin supersedes SI B12 27 16 dated November 2016. The customer complains that the vehicle will not go into ""eDrive"", and in some cases ""eDrive"" is greyed-out in the control display (CID) and is not selectable. Also, there are no pertinent electric drivetrain fault codes that assist with diagnosis. Possible 12 volt battery failure, Intelligent Battery Sensor (IBS) failure or MSA deactivation."
Associated Products (6)Associated Documents - February 1, 2017•Document ID: 10146531Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B120217
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary?ALPINA B7: DME FAULT 102001 - AIR MASS: TOO HIGH IS STORED . Fault is stored in the DME. 102001 - Air mass: too high The Service Engine Soon (MIL) light may be illuminated, however in most cases only the fault is stored. This fault may be difficult to reproduce, but is more likely to occur if driving with a light load followed by extended (off throttle) coasting. DME software diagnostic sensitivity.
Associated Products (2)Associated Documents - November 1, 2016•Document ID: 10146970Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:CRUISE CONTROL
- Mfr Comm. #:
- B662516
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySERVICE ACTION: REPLACE THE ACTIVE CRUISE CONTROL (ACC) SENSOR. Faulty ACC sensor
Associated Products (2)Associated Documents - November 1, 2016•Document ID: 10146969Service Bulletin/Repair InstructionsLANE DEPARTURE: LANE KEEP: STEERING ASSIST
- Mfr Comm. #:
- B662316
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDRIVER ASSISTANCE SYSTEMS FAILURE. Driver Assistance systems failure indicated by CC Message concerning: Camera-based assistance failure Cruise control failure Lack of calibration software for touch control device
Associated Products (2)Associated Documents - November 1, 2016•Document ID: 10146961Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- B621516
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryIMPLAUSIBLE RANGE DISPLAY: INSTRUMENT CLUSTER. Range displayed in the Instrument Cluster is implausible (high or low) and is therefore also displayed incorrectly on the Central Information Display (CID) and the display key. Incorrect instrument cluster software.
Associated Products (2)Associated Documents - November 1, 2016•Document ID: 10146959Service Bulletin/Repair InstructionsSEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- B521015
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryTHE FRONT SEAT VENTILATION FAN MAKES A GRINDING NOISE This Service Information bulletin supersedes SI B52 10 15 dated February 2016.. A grinding noise can be heard from the front ventilation seat, often when going around corners. The fan scrapes against the grille cover Pad foam particles are collected inside the fan causing a noise The Velcro fastener under the seat cover is displaced and hits the fan
Associated Products (2)Associated Documents - November 1, 2016•Document ID: 10146958Service Bulletin/Repair InstructionsSEATS:FRONT ASSEMBLY:POWER ADJUST; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- B520816
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryFRONT SEAT ADJUSTMENT, WRONG DISPLAY/ERROR RECOGNITION (FAULTY DETECTION) IN CID. The seat adjustment is erroneously displayed in the Central Information Display (CID) even though no adjustment was made at the seat switch. Front seat adjustment switch
Associated Products (2)Associated Documents - October 1, 2016•Document ID: 10146905Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B660616
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"? Error Patterns with BMW Display Key This Service Information bulletin supersedes SI B66 06 16 dated April 2016. One or more of the following error patterns occurred while using the BMW display key; these error patterns only occur with the BMW display key: Comfort Access does not work while opening and closing. The BMW display key cannot be charged (USB cable or wirelessly). The BMW display key screen is locked and cannot display vehicle information. The BMW display key displays the Remote Control Parking (RCP) function even though the vehicle is not equipped with option SA 05DV ""Remote Control Parking"" Sporadically, the engine will not start with BMW display key and one of the following CCM ""Check Control messages"" is displayed: · Remote control, remote control not present or faulty. · Not possible to start engine. · Hold the remote near the steering column and then press the START-STOP button. see ""Owner's Handbook"". NOTE: The BMW display key continues to be able to lock/unlock the vehicle with the buttons, and/or the engine started, by emergency detection procedure (placing the BMW display key on the marked area of the steering column). Data lost during the communication between the BMW display key and FBD receiver"
Associated Products (8)Associated Documents - August 1, 2016•Document ID: 10147034Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B641116
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryTemperature of air from vents is opposite of the selection.. Temperature of air (heat vs. cool) from air conditioning system is opposite of the selection. Air temperature matches selection after sleep mode or vehicle restart. All fault codes below will be present in IHKA control unit: 801120 - Motor air distribution rear right: initialization error 801122 - Motor air mix left or air mix: internal error 801126 - Motor air mix right: initialization error 801129 - Motor air mix rear left or air mix rear: initialization error 80112C - Motor air mix rear right: initialization error 801138 - Motor indirect ventilation: initialization error 80110E - Motor ventilation right: initialization error 801105 - Motor circulation: initialization error 801117 - Motor footwell left: initialization error 801114 - Motor layering right: initialization error 801102 - Motor fresh air or fresh air/circulation: initialization error 80110A - Motor ventilation left or ventilation/footwell: internal error 80111A - Motor footwell right: initialization error 801111 - Motor layering left or layering: initialization error 801108 - Motor defrost: initialization error 80111D - Motor air distribution rear left or air distribution rear: initialization error Improper positioning of air distribution flaps in HVAC system.
Associated Products (2)Associated Documents - August 1, 2016•Document ID: 10147032Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B620916
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryINSTRUMENT CLUSTER CLOCK LOSES TIME This Service Information bulletin supersedes SI B62 09 16 dated May 2016.. The time displayed in the KOMBI (instrument cluster) may lose a few minutes each week Internal KOMBI calculation error.
Associated Products (2)Associated Documents - August 1, 2016•Document ID: 10147030Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY:SUN/MOON ROOF ASSEMBLY
- Mfr Comm. #:
- B611616
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryFZD MODULE PROGRAMMING ERROR. During vehicle programming (vehicles with integration level 16-03-502 or below), the Roof Function Center module (FZD) programming aborts. Software error in the FZD.
Associated Products (2)Associated Documents - August 1, 2016•Document ID: 10147020Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; VISIBILITY:SUN/MOON ROOF ASSEMBLY
- Mfr Comm. #:
- B512216
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySUNROOF REOPENS WHEN CLOSING FROM TILT POSITION. Sunroof reopens when initiating automatic close from tilt position (momentary push) even though track is free of obstruction. Sunroof can be closed by initiating closing without anti-trap protection (push and hold after anti-trap reversal). Anti-trap threshold value too sensitive in FZD (Roof Functions Center) software.
Associated Products (2)Associated Documents - August 1, 2016•Document ID: 10147016Service Bulletin/Repair InstructionsTIRES; WHEELS
- Mfr Comm. #:
- B360116
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryROBUSTNESS MEASURE: LOW PROFILE TIRES. Low profile tires have a higher likelihood of failure from road surface and debris impacts. Distance from wheel to tire is shorter than standard profile tires.
Associated Products (2)Associated Documents - August 1, 2016•Document ID: 10147015Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING
- Mfr Comm. #:
- B340616
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"DSC ""WHEEL SPEED SENSOR"" FAULT CODES AND MALFUNCTION INDICATOR LAMP- DIAGNOSTIC. 1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faulty and 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving."
Associated Products (51)Associated Documents - August 1, 2016•Document ID: 10147012Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- B320816
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySTEERING WHEEL HEATER OUTPUT TOO LOW. Steering wheel heater does not get warm in vehicles with Driving Assistant Plus. Ineffective steering wheel electronics control module.
Associated Products (2)Associated Documents - August 1, 2016•Document ID: 10147007Service Bulletin/Repair InstructionsPOWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- B270116
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySERVICE ACTION: REPLACE THE DUST BOOT ON THE TRANSFER CASE. The dust boot (gaiter) for the front drive shaft at the transfer case may allow debris to enter the joint for the front driveshaft at the transfer case. The material of the dust boot may tear.
Associated Products (2)Associated Documents