BMW M6 Service Bulletins (2015)
266 manufacturer communications on file.
- July 1, 2014•Document ID: 10148134Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRear View Camera Does Not Display Image on CID. After engaging the reverse gear, the reversing camera does not display a picture in the CID (Central Information Display). CAUSE The drive mechanism for the roundel actuation in the boot lid is faulty.
Associated Products (12)Associated Documents - July 1, 2014•Document ID: 10148132Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE
- Mfr Comm. #:
- 660414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
Associated Products (94)Associated Documents - July 1, 2014•Document ID: 10148130Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEATS
- Mfr Comm. #:
- 652113
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryWhen Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
Associated Products (78)Associated Documents - July 1, 2014•Document ID: 10148129Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 651614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCentral Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
Associated Products (70)Associated Documents - July 1, 2014•Document ID: 10148128Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
Associated Products (81)Associated Documents - July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - July 1, 2014•Document ID: 10148118Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 511514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Center Console Lock Cylinder. The center console lock cylinder is loose. Manufacturing tolerances of the center console lock cover cap may cause it to become loose or missing. AFFECTED VEHICLES This Service Action involves F01, F02, F06, F07, F12 and F13 vehicles produced from March 7, 2014 to April 23, 2014. First check if a Service Action label with a code number 688 is already attached to the B-pillar. If a code number 688 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
Associated Products (24)Associated Documents - June 1, 2014•Document ID: 10148101Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Associated Products (215)Associated Documents - May 1, 2014•Document ID: 10148333Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
Associated Products (79)Associated Documents - May 1, 2014•Document ID: 10148312Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE; SUSPENSION:FRONT:WHEEL BEARING
- Mfr Comm. #:
- 310112
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (70)Associated Documents - May 1, 2014•Document ID: 10148308Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (82)Associated Documents - April 1, 2014•Document ID: 10148276Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 650514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTraffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
Associated Products (209)Associated Documents - April 1, 2014•Document ID: 10148273Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (242)Associated Documents - April 1, 2014•Document ID: 10148258Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (80)Associated Documents - March 1, 2014•Document ID: 10148010Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Associated Products (211)Associated Documents - March 1, 2014•Document ID: 10147921Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- 360114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFitting Winter Tires Properly to Vehicles with Ceramic Brakes. Wheel studs may loosen after wheels for the rear axle are incorrectly fitted to the front axle on vehicles equipped with option 2NK (ceramic brakes). Incorrect installation of rear axle winter tires (wheel style 409M) onto the front axle in conjunction with ceramic brakes
Associated Products (33)Associated Documents - March 1, 2014•Document ID: 10147918Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION There is an error in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. The vehicle may also exhibit rough running at idle and while driving. F07 and F10: P/N 13 64 7 639 994 is for all vehicles produced from 7/2014 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2014 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 F06, F12 and F13: P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 Until further notice, it is good practice to verify that the injector part number being removed from the engine matches the new injector part number. Always review the vehicle history to identify if the injectors have already been replaced. When the ETK data is corrected, a notification will be distributed. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16028.3.B130413... 4/24/2014
Associated Products (35)Associated Documents - February 1, 2014•Document ID: 10147985Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMy BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
Associated Products (66)Associated Documents - February 1, 2014•Document ID: 10147984Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 840613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
Associated Products (94)Associated Documents - February 1, 2014•Document ID: 10147982Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 652313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
Associated Products (98)Associated Documents