BMW 650i Service Bulletins (2012)
363 manufacturer communications on file.
- February 1, 2015•Document ID: 10147085Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 613014
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"SI B61 30 14February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated January 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
Associated Products (43)Associated Documents - February 1, 2015•Document ID: 10147084Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 610314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
Associated Products (115)Associated Documents - February 1, 2015•Document ID: 10147077Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 270213
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySI B27 02 13February 2015 Intermediate and Special Transmission Technical Service This Service Information bulletin supersedes SI B27 02 13 dated June 2013. designates changes to this revision SUBJECT Knocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
Associated Products (54)Associated Documents - February 1, 2015•Document ID: 10147068Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 111614
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (59)Associated Documents - January 1, 2015•Document ID: 10147628Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- 840115
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "
Associated Products (88)Associated Documents - January 1, 2015•Document ID: 10147626Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 652413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
Associated Products (118)Associated Documents - January 1, 2015•Document ID: 10147625Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 651312
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
Associated Products (132)Associated Documents - January 1, 2015•Document ID: 10147624Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 651009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (222)Associated Documents - January 1, 2015•Document ID: 10147623Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 650509
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
Associated Products (216)Associated Documents - January 1, 2015•Document ID: 10147618Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"This Service Information bulletin supersedes SI B61 03 13 dated August 2013. designates changes to this revision SUBJECT High Battery Discharge Warning: Battery Needs Replacement. After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: z Unfavorable driving profile - excessive short trips z Excessive terminal 30B after run - normal coolant pump or electric fan operation z Extremely cold temperatures z Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups."
Associated Products (22)2014 BMW 550i2013 BMW 550i2013 BMW 650i2013 BMW 750i2013 BMW 750Li2013 BMW F 800 R2013 BMW R 1200 GS2012 BMW 550i2012 BMW 650i2012 BMW 750i2012 BMW 750Li2012 BMW ActiveHybrid 72011 BMW 550i2011 BMW 750i2011 BMW 750Li2011 BMW ActiveHybrid 72011 BMW R 1200 GS2010 BMW 550i2010 BMW 750i2010 BMW 750Li+ 2 moreAssociated Documents - January 1, 2015•Document ID: 10147599Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:ACCELERATOR PEDAL; VEHICLE SPEED CONTROL
- Mfr Comm. #:
- 120915
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the ""fuel consumption, current"" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold."
Associated Products (90)Associated Documents - January 1, 2015•Document ID: 10147595Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- 120415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
Associated Products (191)Associated Documents - January 1, 2015•Document ID: 10147593Service Bulletin/Repair InstructionsENGINE; EQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 110614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: z Hot-Film Air Mass Sensors z PIEZO High Pressure Fuel Injectors z Engine Vacuum Pump z Fuel System Low Pressure Sensor/Feed Line z Fresh Air Intake Turbo Seals z Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Information"" section below)."
Associated Products (61)Associated Documents - January 1, 2015•Document ID: 10147591Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
- Mfr Comm. #:
- 110215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)
Associated Products (79)Associated Documents - December 1, 2014•Document ID: 10148195Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.
Associated Products (116)Associated Documents - December 1, 2014•Document ID: 10148194Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840412
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
Associated Products (204)Associated Documents - December 1, 2014•Document ID: 10148192Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 652214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryAutomated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.
Associated Products (120)Associated Documents - December 1, 2014•Document ID: 10148184Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- 613014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBMW Maintenance Program: 12-Volt Battery Replacement Measure.
Associated Products (73)Associated Documents - December 1, 2014•Document ID: 10148181Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER; SERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, AIR:DISC:CALIPER
- Mfr Comm. #:
- 340614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryM5 and M6 Front Axle Brake Squeak with Compound Brake System. A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a squeaking noise.
Associated Products (33)Associated Documents - December 1, 2014•Document ID: 10148180Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM
- Mfr Comm. #:
- 340514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDynamic Stability Control Unit (DSC) Aborted when Programming Vehicle. If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software
Associated Products (72)Associated Documents