BMW 650i Service Bulletins (2012)
363 manufacturer communications on file.
- February 1, 2016•Document ID: 10151071Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"This Service Information bulletin and attachment supersedes SI B11 16 14 dated May 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (57)Associated Documents - January 1, 2016•Document ID: 10151023Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B650709
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryWhistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
Associated Products (289)Associated Documents - January 1, 2016•Document ID: 10151015Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B613014
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySI B61 30 14. January 2016. General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 30 14 dated December 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure . INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.
Associated Products (44)Associated Documents - January 1, 2016•Document ID: 10151009Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B510116
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"Heated rear window control module requires a software update. The electrical load of the heated rear window may cause the fuse to overheat and fail. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Associated Products (14)Associated Documents - January 1, 2016•Document ID: 10150905Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; EQUIPMENT
- Mfr Comm. #:
- B161514
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySI B16 15 14 January 2016 Fuel Supply Systems Technical Service.This Service Information bulletin supersedes SI B16 15 14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.
Associated Products (103)Associated Documents - December 1, 2015•Document ID: 10147884Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- B621215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryInstrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
Associated Products (126)Associated Documents - December 1, 2015•Document ID: 10147882Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B613014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"?SI B61 30 14December 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated July 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months. "
Associated Products (69)Associated Documents - December 1, 2015•Document ID: 10147871Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- B340614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?SI B34 06 14December 2015 BrakesTechnical Service This Service Information bulletin supersedes SI 34 06 14 December 2014. designates changes to this revision SUBJECT M5 and M6 Front Axle Brake Squeak with Compound Brake System. A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a squeaking noise.
Associated Products (41)Associated Documents - December 1, 2015•Document ID: 10147868Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B160915
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySI B16 09 15 Fuel Supply Systems. December 2015 Technical Service. This Service Information bulletin supersedes SI 26 01 15 dated November 2015. The wrong temperature sensor for the Natural Vacuum Leak Detection (NVLD) may have been installed.
Associated Products (42)Associated Documents - November 1, 2015•Document ID: 10147833Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B650915
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
Associated Products (132)Associated Documents - November 1, 2015•Document ID: 10147831Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- B621015
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software."
Associated Products (92)Associated Documents - November 1, 2015•Document ID: 10147830Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B620715
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles ""arriving"" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed ""prior"" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2. "
Associated Products (88)Associated Documents - November 1, 2015•Document ID: 10147827Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B612215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRear Window Defroster is Inoperative. The rear window defroster no longer works. Fuse 203 (30A) in the rear power distribution box is blown and the power distribution box may show signs of overheating. Excessive power consumption of the rear window defroster overloads the circuit.
Associated Products (14)Associated Documents - November 1, 2015•Document ID: 10147808Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Associated Products (56)Associated Documents - October 1, 2015•Document ID: 10147779Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- B620715
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryInstrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.
Associated Products (94)Associated Documents - October 1, 2015•Document ID: 10147762Service Bulletin/Repair InstructionsPOWER TRAIN:DRIVELINE
- Mfr Comm. #:
- B123715
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 - Drivetrain Malfunction Warning with Quantity Control Valve Faults. The Drivetrain Malfunction message is displayed and any of the following faults for the quantity control valves are stored in the DME. 11C302 - Fuel- supply control valve 2, activation: short circuit to ground or open circuit 11C401 - Quantity control valve, activation: short circuit to ground 1F4C04 - Relay, quantity control valve: open circuit The most likely cause is the high fuel pressure quantity control valve relay (K6342) loose connection at the electrical connector.
Associated Products (29)Associated Documents - October 1, 2015•Document ID: 10147759Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.
Associated Products (56)Associated Documents - September 1, 2015•Document ID: 10147241Service Bulletin/Repair InstructionsWHEELS; POWER TRAIN:DRIVELINE
- Mfr Comm. #:
- B270415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryShudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Associated Products (176)Associated Documents - August 1, 2015•Document ID: 10151404Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B270315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryVibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
Associated Products (142)Associated Documents - August 1, 2015•Document ID: 10151400Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- B111715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N63 and S63 Engine: Upper Oil Pan Removal and Installation Procedures. INFORMATION When removing and/or installing the N63 or S63 engine ""upper"" oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the upper oil pan bolts as per Repair Instruction 11 13 010 ""Removing and installing /replacing upper oil sump (N63),"" the steps outlined in the attachment of this bulletin must be followed. Refer to attached document and the instruction section that applies to the procedure being carried out. The ISTA/D repair instructions are currently being revised."
Associated Products (58)Associated Documents