Gulf States Toyota, Inc. (GST) is recalling certain Toyota 2023 GR Supra, 2024 4 Runner, Corolla, Grand Highlander, Grand Highlander Hybrid, Land Cruiser Hybrid, Tacoma, Tacoma Hybrid, 2023-2024 BZ4X, Corolla Cross Hybrid, GR Corolla, GR86, Highlander, Highlander Hybrid, Prius, Prius Prime, Sequoia Hybrid, Tundra, Tundra Hybrid, Venza Hybrid, 2023-2025 Crown, and 2025 Camry Hybrid vehicles equipped with GST accessories. The load carrying capacity modification label may display inaccurate added weight values. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Had my engine spin a bearing in 2023 and was told to report what had happened. The car was used in track days prior to this but while driving down the highway afterwards it lost oil pressure and spun a nearing. Had it towed Twin City Toyota, a dealer and had them give me the run around with it. Saying it had hit the limiter 60 miles before the issue accrued and that it “over revved 13 rpms” and that since it had hit the limiter and being a stick shut it voided my warranty. Told me I would have to pay 26K for a new motor and if not to get my car out of there. They also refused to give me any documentation for it and what they claimed was on the cars data stream. Toyota corporate also got involved and said they changed the warranty terms after I bought the car and wouldn’t warranty it because of what the dealer was claiming.
No injuries · No fire · No crash
Vehicle experienced catastrophic engine failure while driving at 45mph. Inspection results from Toyota said the issue was a rod failure due to a spun bearing no cause ever determined by Toyota. Engine failure like this while in operation could lead to serious injury or death under the right circumstances. No engine lights to indicate prior problem and vehicle was serviced less than a month before incident occurred. Vehicle was under warranty but Toyota refused to honor the warranty. Oil starvation is the number one cause of spun bearing leading to engine failure Toyota didn't even consider this as a potential cause because of the implication. There are countless stories from GR86 and BRZ owners that have experienced the same engine failure. The RTV sealant Toyota is using to seal the oil pans is being over applied at production and leaking into the pan getting sucked into the oil pickup and causing the oil starvation that is destroying the engines. There needs to be a recall on all GR86 models that had RTV used to seal the pans and have them fitted with a proper gasket to eliminate this issue.
No injuries · No fire · No crash
My engine started smoking and eventually completely stopped on side of road. There were no warning lights or errors until issues started.it found have exploded or I could have been seriously injured as I was on expressway.
No injuries · No fire · No crash
While driving on the highway at approximately 80–90 mph, the vehicle experienced an unexpected RPM increase as I came off the accelerator, an engine-misfire warning, sudden loss of power, and engine shutdown. I immediately pulled over. Smoke came from the engine compartment, engine oil had been expelled throughout the engine bay, and oil was leaking underneath the vehicle. The vehicle became completely inoperable, creating a serious safety risk at highway speed. An independent Toyota Master Technician later documented catastrophic internal failure involving Cylinder No. 2. The piston and connecting-rod assembly were destroyed, the connecting rod contacted the engine block, a hole was present through the short block, extensive metal debris was found in the oil pan, piston material was crushed into the oil pan, an internal valvetrain component was also found there, and the engine was seized, limiting any teardown. The technician also observed material consistent with factory-applied FIPG/RTV sealant in the oil-pickup area and separate sealant-like material protruding into a head-gasket passage where it should not have been present. He stated that the location was consistent with excess sealant being applied during assembly and squeezed inward, supporting the possibility of a manufacturing-related defect. He stated that proper evaluation should have included measuring the amount of sealant and any obstruction, inspecting the oil pump, filter, bearings, oil-pan debris, and evaluating for restricted oil flow. Those measurements and results were not provided by the dealership or Toyota. Instead, I had to call law enforcement to receive a minimal repair order and my car at no cost from the dealership 8 months later. I am reporting this because excess factory sealant intruding into an oil-related or head-gasket passage could potentially restrict lubrication and create a serious safety concern if similar conditions exist in other vehicles, which have also been documented.
No injuries · No fire · No crash
Engine blew around May, what caused this issue would be unknown even though the dealership said it was excessive RTV on the oil pan, there was no RTV on the oil pan (i have a picture). I was driving on the highway and slowing down to take my exit, it happened around 25mph, car got stuck on 3rd gear if im not mistaken (its an automatic transmission by the way). Ended up with 3 holes in the engine block, a missing valve, oil all over the engine bay which caused the car to release white smoke through exhaust and hood.
No injuries · No fire · No crash