MINI Clubman Service Bulletins (2017)
139 manufacturer communications on file.
- November 1, 2016•Document ID: 10146979Service Bulletin/Repair InstructionsEQUIPMENT; STEERING
- Mfr Comm. #:
- M320116
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
Summary"EPS INTERMITTENT ASSIST FAILURE, FC 4823FA. The steering assistance fails after several, consecutive parking maneuvers or sustained hold at the end stop. EPS assistance starts functioning again after a few minutes. And, Fault code 4823FA (""EPS control unit internally overload, reduction in steering assistance"") is stored in the EPS control module. EPS software error (overloading protection function over sensitivity)."
Associated Products (4)Associated Documents - November 1, 2016•Document ID: 10146977Service Bulletin/Repair InstructionsSUSPENSION:FRONT; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- M310315
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryCRACKING NOISE IN THE AREA OF THE FRONT AXLE SUPPORT/WISHBONE This Service Information bulletin supersedes SI 31 03 15 dated February 2016. Cracking noise coming from the area of the front axle when driving over rough road surfaces, railroad crossings and speed bumps. CAUSE Wishbone rubber mount.
Associated Products (6)Associated Documents - November 1, 2016•Document ID: 10146976Service Bulletin/Repair InstructionsSUSPENSION:FRONT
- Mfr Comm. #:
- M310115
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryGroaning/squeaking noise from the front of the vehicle. A groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle.
Associated Products (6)Associated Documents - November 1, 2016•Document ID: 10146975Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- M270116
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryF54 ALL4: FAULT CODE 440317 STORED IN THE LMV. The following Check Control Message (CCM) is displayed in the instrument cluster: CCM 350: Driving stabilization. Drive at a moderate speed. The following entry is present in the fault memory of the LMV: 440317 - Pump motor: General multiple fault. Further fault memory entries can occur in combination: DSC: 48068C - Transfer box - clutch closed down temporarily, possible overheating. 48078A - All-wheel drive clutch - clutch position open, only front-wheel drive. LMV: 440304 - Pump motor: Current too low Unfavorable software of the longitudinal torque distribution module (LMV).
Associated Products (4)Associated Documents - October 1, 2016•Document ID: 10146927Service Bulletin/Repair InstructionsSUSPENSION; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- M511016
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
Summary"SERVICE ACTION: CHECKING AND REWORKING PVC SEAM ON STRUT TOWER. A PVC seam of the front strut spring tower may not be providing the necessary corrosion protection. Improper application of seam sealer. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Associated Products (4)Associated Documents - October 1, 2016•Document ID: 10146925Service Bulletin/Repair InstructionsSTEERING; STEERING:ELECTRIC POWER ASSIST SYSTEM
- Mfr Comm. #:
- M320114
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryThe power assisted steering is unavailable at start up. No communication with the Electric Power Steering (EPS). Multiple possible fault codes. Cause: Electric Power Steering (EPS). Perform a vehicle test with ISTA to identify fault code entrie
Associated Products (6)Associated Documents - October 1, 2016•Document ID: 10146924Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- M120615
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
Summary"ENGINE POWER REDUCTION WITH "CLUTCH DAMAGED"" FAULTS STORED This Service Information bulletin supersedes SI M12 06 15 dated July 2015. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. F54, F55, F56, F57Target Integration level: F056-16-11-501 or higherThe vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."
Associated Products (14)Associated Documents - September 1, 2016•Document ID: 10146875Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- M640214
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryFoul Odor when Switching On A/C. The customer reports a foul smell (musty, rotten, and vinegary) when the A/C is first turned on that lasts about five minutes. Micro-filter position too low in the IHKA housing.
Associated Products (6)Associated Documents - September 1, 2016•Document ID: 10146874Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- M640116
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummaryWater Ingress In Footwell Area From A/C Condensate Drain This Service Information bulletin supersedes SI M64 01 16 dated March 2016.. Damp front foot-well carpet after long period of air conditioning use. Musty odor in the vehicle (moldy, old socks, laundry room). The A/C condensate drain hose is blocked by the heatshield. The A/C condensate drain hose is not attached properly to the housing. The A/C condensate drain hose was damaged during installation or previous repair.
Associated Products (6)Associated Documents - September 1, 2016•Document ID: 10146871Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- M511216
- Date Added:
- November 5, 2018
- Manufacturer:
- MINI
SummarySERVICE ACTION: RUBBER STRIP ON REAR SIDE WINDOW TRIM IS CRACKED. The rubber strip on the rear side window trim may crack. In some cases a gap may be evident on the rubber trim strip. Results are cosmetic- no water leakage or sound intrusion. Combination of unfavorable materials.
Associated Products (4)Associated Documents - August 1, 2016•Document ID: 10147586Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- M620216
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
SummaryPERCEIVED SCRATCH IN INSTRUMENT CLUSTER. INFORMATION Replacing the instrument cluster for this issue will NOT be covered or reimbursed under MINI limited warranties. [ Copyright (c)2016 BMW of North America, Inc. ] Page 1 of 3 Page 2 of 2 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016 Page 1 of 3 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016
Associated Products (6)Associated Documents - August 1, 2016•Document ID: 10147585Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD WIPER/WASHER; VISIBILITY:WINDSHIELD
- Mfr Comm. #:
- M610116
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
SummarySI M61 01 16 General Electrical Systems August 2016 Technical Service Front Windshield Wiper Noises This Service Information bulletin supersedes SI M61 01 16 dated April 2016.. Customer complains wipers are noisy or chattering during wiper operation. CAUSE Wiper arms out of adjustment and/or windshield cowl misaligned.
Associated Products (6)Associated Documents - August 1, 2016•Document ID: 10147581Service Bulletin/Repair InstructionsVISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- M510616
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
SummarySQUEAKING NOISE FROM POWER FOLDING EXTERIOR REARVIEW MIRRORS. A squeaking noise can be heard when folding the exterior rear view mirrors in or out. Tolerances in the exterior rear view mirrors
Associated Products (6)Associated Documents - August 1, 2016•Document ID: 10147580Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING
- Mfr Comm. #:
- M340216
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
SummaryDRIVING STABILIZATION CONTROL FAILURE: ABS/DSC INSTRUMENT LAMPS LIT- DIAGNOSIS. 1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faultyand 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving.
Associated Products (6)Associated Documents - August 1, 2016•Document ID: 10147579Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING
- Mfr Comm. #:
- M340116
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
SummaryDRIVING STABILIZATION CONTROL FAILURE: ABS/DSC INSTRUMENT LAMPS LIT. ABS/DSC lamps lit in instrument cluster. Fault codes may be saved in the DSC control unit: 480AAD - wheel speed sensor - rear left - smoke monitoring 480AAC - wheel speed sensor - rear left - unexpected jump in the signal 4809B9 - wheel speed sensor - rear left - driving off recognition faulty 480716 - wheel speed sensor - rear left - plausibility: direction of rotation 4809B7 - wheel speed sensor - rear left - missing tooth 480719 - wheel speed sensor - rear right - plausibility: direction of rotation 480686 - wheel speed sensor - rear right - driving off recognition faulty 480AB3 - wheel speed sensor - rear right - unexpected jump in the signal 480AB4 - wheel speed sensor - rear right - smoke monitoring 4809C2 - wheel speed sensor - rear right - missing tooth Rear wheel pulse generator (wheel speed sensor) retaining screw is loose, missing or broken.
Associated Products (6)Associated Documents - August 1, 2016•Document ID: 10147578Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE
- Mfr Comm. #:
- M310115
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
SummaryA groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle.
Associated Products (6)Associated Documents - August 1, 2016•Document ID: 10147576Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- M111016
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
Summary"THERMOSTAT FAULTS (B-ENGINES). The Service Engine Soon light is on. A Check Control message for ""Engine overheated"" and or ""Exercise caution!"" may also display. The following fault codes may be stored in the DME: 1D2401 - Characteristic map thermostat, actuation: Short circuit to B+ 1D2402 - Characteristic map thermostat, actuation: Short circuit to ground 1D2404 - Characteristic map thermostat, actuation: Line disconnection During diagnosis the coolant may be found to be discolored. Insulation on the wiring for the map activation thermostat (heating element) may be damaged. Exposed wiring may allow coolant to enter the harness. This may cause damage to the heating element."
Associated Products (6)Associated Documents - June 1, 2016•Document ID: 10151390Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT
- Mfr Comm. #:
- M640216
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryAir Conditioning Refrigerant R1234yf Introduction. INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipment may be an indication of refrigerant/equipment incompatibility with the vehicle's system. Always carefully ascertain the type of refrigerant used in the vehicle's system before performing service. Labels on underside of hood, will detail which refrigerant is used in the air conditioning system. Service the vehicle with compatible recycling equipment ONLY. Attempts to adapt and use incompatible service tools will destroy both the vehicle's air conditioning system and the service tool. Never use any R-12/R134a service tools on R1234yf systems. Tools, such as manifold gauge sets, retain small amounts of refrigerant and lubricant. Attempting to use the same equipment on both R-12/R134a and R1234yf vehicles will contaminate the air conditioning systems. Obtain and use the correct type of refrigerant recovery/recycling machine. Follow the directions included in the machine's instruction manual. WARR
Associated Products (8)Associated Documents - June 1, 2016•Document ID: 10151389Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- M620515
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryThe Clock in the Instrument Cluster Loses time This Service Information Bulletin supersedes SI M62 05 15 dated June 2016. The time displayed in the instrument cluster (KOMBI) may lose a few minutes each week and the clock needs to be adjusted periodically.
Associated Products (8)Associated Documents - June 1, 2016•Document ID: 10151386Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- M110916
- Date Added:
- December 10, 2018
- Manufacturer:
- MINI
SummaryVANOS AND VANOS CENTRAL BOLT IDENTIFICATION. INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.
Associated Products (8)Associated Documents