Mazda CX-30 Service Bulletins (2021)
606 manufacturer communications on file.
- November 15, 2022•Document ID: 10226889Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEATS
- Mfr Comm. #:
- 09-044-22
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs "B1030:13" and/or "B1032:13" are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. - B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) - B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)
Associated Products (4)Associated Documents - November 14, 2022•Document ID: 10226924Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-075-22
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummaryIf you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple CarplayâÃÂâ/ Android AutoâÃÂâ will not connect) 6. Over-sized wheels/tires (incorrect GPS location)
Associated Products (19)Associated Documents - November 14, 2022•Document ID: 10226923Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM
- Mfr Comm. #:
- SA-074-22
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.
Associated Products (12)Associated Documents - November 9, 2022•Document ID: 10226826Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 09-001-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may experience white-streak stains appearing on the front door that look like they seeped out from under the outer mirror base. This is caused by water intruding from gaps of the outer mirror body and/or the hinge of the outer mirror, and corrosion occurring on the aluminum die-cast inner base in the outer mirror. Water, including white-salty corrosion, may drip out from gaps under the outer mirror base resulting in white stains on the front door. To eliminate this concern, the front outer mirror inner base has been modified.
Associated Products (2)Associated Documents - November 7, 2022•Document ID: 10226816Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 01-011-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may have a "LOW ENGINE OIL LEVEL" warning message and a CHECK ENGINE light illuminated in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. - DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the design of these valve seals has been modified.
Associated Products (7)Associated Documents - November 4, 2022•Document ID: 10226898Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 16-004-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.
Associated Products (8)Associated Documents - November 2, 2022•Document ID: 10226916Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-064-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may comlpain about an intermittent Beep sound (popping sound) every 1 ~ 2 minutes while driving. This may be cause by a software error in the navigation SD card.
Associated Products (9)Associated Documents - November 1, 2022•Document ID: 10226918Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-070-22
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain about intermittent audio no sound from the MAZDA CONNECT infotainment system and/or static noise from the speakers. The concern may be reproduced by tapping on the dash pad near the MAZDA CONNECT center display and the following DTC's may be stored. * U0186:08 Communication error with audio amplifier * U2145:08 Communication error with remote tuner (RT) * U2145:02 Communication error with remote tuner (RT) This may be caused by PIN 6F backing out at the CMU connector 0920-101F.
Associated Products (6)Associated Documents - November 1, 2022•Document ID: 10226896Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 16-001-22d
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA01_12004 or later). Ver. 7000C0A-NA01_12004 fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * The center display may turn black when the gear is shifted from reverse position to parking position. * Screen freezes and goes to white screen, then the system reboots. * Steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms. - No sound comes out from the speakers. - Audio source selection is unavailable. * When using the navigation with head-up mode, the vehicle icon rotates. * Beep sounds every after couple of minutes. * Language setting may not be accepted correctly. * The audio track may not pause when pressing the mute button. * The system reboots. * The screen may turn black when trying to play a video file in the USB connected device.
Associated Products (4)Associated Documents - October 28, 2022•Document ID: 10225784Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- 09-042-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit windshield glass distortion or a double-image from the active driving display. These may be due to a) distortion in the windshield glass not properly removed during the manufacturing process or b) glass with incorrect specifications used in the manufacturing process. To eliminate these concerns, the windshield glass manufacturing process has been modified.
Associated Products (2)Associated Documents - October 19, 2022•Document ID: 10225779Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 09-016-22a
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain that the rear console lid does not slide smoothly. This may be caused by improperly positioned felt pads attached to the rear console lid lock, which may have moved out of position after repetitive use. The exposed adhesive residue may stick to the rail and disrupt smooth sliding operation. To eliminate this concern, the felt pad positions have been changed.
Associated Products (4)Associated Documents - October 19, 2022•Document ID: 10225776Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 01-013-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome customers may experience the CHECK ENGINE light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: * The engine takes longer to warm up * The engine temperature gauge fluctuates * The low coolant temperature indicator (blue) light stays on longer or comes on while driving * Poor heater performance, especially at idle NOTE: * Vehicles with SKYACTIV-G 2.5T are not applicable. * If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies, this information is not applicable. Diagnose according to the instructions in MGSS. Due to production variety of the failsafe thermostat integrated in the coolant control valve, engine coolant may enter into a dry hollow in the failsafe thermostat, resulting in unintended opening of the failsafe thermostat at lower temperatures (104-176 ðF (40-80 ðC)). To eliminate this concern, the production process of the coolant control valve has been modified.
Associated Products (5)Associated Documents - October 17, 2022•Document ID: 10225785Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 16-005-22a
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Ver. 7000C0A-NA06_12012 or later).
Associated Products (4)Associated Documents - October 17, 2022•Document ID: 10225767Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SA-068-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummaryThe new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
Associated Products (16)Associated Documents - October 17, 2022•Document ID: 10225724Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- SA-008-22a
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
Associated Products (19)Associated Documents - October 12, 2022•Document ID: 10225763Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-067-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).
Associated Products (15)Associated Documents - October 12, 2022•Document ID: 10225761Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-066-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.
Associated Products (18)Associated Documents - October 10, 2022•Document ID: 10225778Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 07-004-22a
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain the A/C blows warm. This may be caused by one of two things. Cause 1: After accelerating in hot weather, the A/C blows warm air for a longer time than other models. This is caused by improper control software of the PCM not allowing the A/C compressor to resume properly after acceleration. During a hard acceleration above a certain throttle level opening, the PCM stops the A/C compressor operation for better acceleration. It then resumes the compressor operation after the acceleration. To eliminate this concern, the control software of the PCM has been modified. Cause 2: Insufficient cooling performance at ambient temperature of around 68 ðF (20 ðC) in daytime. This is caused when both the ambient temperature and the cabin temperature are at around 20 ðC (68 ðF), auto A/C set at around 20 ðC (68 ðF) may not cool down the cabin temperature properly. To eliminate this concern, control software of the dash-electrical supply unit (Dash-ESU) has been modified.
Associated Products (4)Associated Documents - October 10, 2022•Document ID: 10225751Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- SA-065-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles equipped with a coolant control valve may exhibit difficulties when refilling the coolant because the control valve is closed and air in the engine cannot escape during ignition ON. Therefore, turn the ignition OFF when refilling engine coolant using the radiator filler neck.
Associated Products (11)Associated Documents - October 10, 2022•Document ID: 10225730Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SA-019-22b
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummaryMazda Connected Services Frequently Asked Questions (FAQs)
Associated Products (13)Associated Documents