Genesis GV70 Service Bulletins (2024)
50 manufacturer communications on file.
- November 15, 2023•Document ID: 10245584Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 23-DS-003G
- Date Added:
- November 30, 2023
- Manufacturer:
- GENESIS
SummaryWhen servicing any of the specified vehicles below with the corresponding DTCs, follow the step-by-step procedures in this bulletin. ⢠Electronic-Limited Slip Differential (E-LSD) actuator DTC codes P188213, P188900, or P189600
Associated Products (7)Associated Documents - November 15, 2023•Document ID: 10245583Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 23-DS-002G
- Date Added:
- November 30, 2023
- Manufacturer:
- GENESIS
SummaryWhen servicing any of the specified vehicles below with the corresponding DTCs, follow the step-by-step procedures in this bulletin. ⢠Transfer case actuator DTC codes P196000, P195800, or P195513
Associated Products (4)Associated Documents - October 12, 2023•Document ID: 10244962Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR; POWER TRAIN
- Mfr Comm. #:
- 23-01-082G
- Date Added:
- November 6, 2023
- Manufacturer:
- GENESIS
SummaryThis Vehicle Control Unit (VCU) software package includes the following key VCU updates: ⢠Brake light logic update for regenerative braking. o Revised logic to enable brake light actuation during regenerative braking at certain deceleration speeds and during i-Pedal mode driving without the need to press the brake pedal ⢠i-Pedal mode operation logic update. ï§ Revised i-Pedal operation logic. ⢠12V battery saver logic update allows
Associated Products (4)Associated Documents - October 9, 2023•Document ID: 10244957Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 23-DS-004G-1
- Date Added:
- November 6, 2023
- Manufacturer:
- GENESIS
SummaryCertain GV70 (JK1 and JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a noise condition from the rear differential at certain speeds while accelerating or decelerating. This bulletin describes the procedure to inspect the vehicle for noise and if necessary to tighten the lock nut or if necessary replace the differential.
Associated Products (11)Associated Documents - October 9, 2023•Document ID: 10244956Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 23-FL-006G
- Date Added:
- November 6, 2023
- Manufacturer:
- GENESIS
SummaryNeutral Coasting Mode may not activate under certain conditions when the battery State of Charge (SOC) is less than 75%. This update revises the software logic to be activated regardless of battery SOC.
Associated Products (7)Associated Documents - September 21, 2023•Document ID: 10243370Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 23-01-069G-1
- Date Added:
- October 2, 2023
- Manufacturer:
- GENESIS
SummaryCertain 2023MY G80 Electrified (RG3 EV), 2023-24MY GV60 (JW1 EV), and 2023-24MY GV70 Electrified (JK1a EV) vehicles may have a condition where low 12V auxiliary battery charging occurs due to an ICCU (Integrated Charge Control Unit) fault and may set the following DTC P1A9096 â âDC/DC Converter Input Voltage Sensor Faultâ. When a fault occurs, the vehicle may enter a reduced power mode while various warning lights, an audible chime will sound, and large messaging in the vehicleâs instrument cluster will appear, instructing the driver to stop the vehicle. The vehicle will be inspected for a DTC P1A9096 and may require either an ICCU software update or ICCU replacement and fuse replacement.
Associated Products (4)Associated Documents - September 12, 2023•Document ID: 10243320Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 23-ST-004G-1
- Date Added:
- October 2, 2023
- Manufacturer:
- GENESIS
SummaryThis bulletin describes the procedure to inspect the steering universal joint dust cover for noise, and if necessary, apply grease on certain Genesis vehicles.
Associated Products (13)Associated Documents - August 17, 2021•Document ID: 10253048Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 21-AT-015G
- Date Added:
- April 11, 2024
- Manufacturer:
- GENESIS
SummaryThis TSB provides a procedure to diagnose and repair a transmission for the following Incorrect Ratio DTC (transmission clutch slipping more than 200 rpm in gear).
Associated Products (20)2025 Genesis GV702024 Genesis G702024 Genesis G802024 Genesis G902024 Genesis GV702024 Genesis GV802023 Genesis G702023 Genesis G802023 Genesis G902023 Genesis GV702023 Genesis GV802022 Genesis G702022 Genesis G802022 Genesis G902022 Genesis GV702022 Genesis GV802021 Genesis G702021 Genesis G802021 Genesis G902021 Genesis GV80Associated Documents - February 3, 2021•Document ID: 10253049Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- 21-BD-001G
- Date Added:
- April 11, 2024
- Manufacturer:
- GENESIS
SummaryGenesis applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
Associated Products (22)2025 Genesis GV702024 Genesis G702024 Genesis G802024 Genesis G902024 Genesis GV602024 Genesis GV702024 Genesis GV802023 Genesis G702023 Genesis G802023 Genesis G902023 Genesis GV602023 Genesis GV702023 Genesis GV802022 Genesis G702022 Genesis G802022 Genesis G902022 Genesis GV702022 Genesis GV802021 Genesis G702021 Genesis G80+ 2 moreAssociated Documents - July 27, 2020•Document ID: 10253038Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN
- Mfr Comm. #:
- 21-AT-012G
- Date Added:
- April 11, 2024
- Manufacturer:
- GENESIS
SummaryThis bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. ï· Before replacing an automatic transmission (Pages 2~3): Input the data from the new transmission into the TCU using the GDS. ï· Before replacing a TCU (Pages 4~6): Back up the oil pressure data from the old TCU into the GDS and then transfer the data to the new TCM.
Associated Products (16)Associated Documents