BMW Z4 Service Bulletins (2014)
116 manufacturer communications on file.
- July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - June 1, 2014•Document ID: 10148101Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Associated Products (215)Associated Documents - June 1, 2014•Document ID: 10056099Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; COMMUNICATION
- Mfr Comm. #:
- SIB-84-03-14
- Date Added:
- September 3, 2014
- Manufacturer:
- BMW
SummaryBMW: WHEN USING IPHONE, VARIOUS CONNECTIVITY FAILURES OCCUR, SUCH AS DISCONNECTION OF CALL, LIST OF CONTACTS INCOMPLETE, DUE TO THE VARIANTS AND SOFTWARE USED. MODEL 2008-2014.
Associated Products (30)Associated Documents - May 1, 2014•Document ID: 10148327Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 540414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Wiring Harness Sensor Rear Module. The wiring harness for the convertible top rear module sensor may be positioned incorrectly, which can cause damage to the wiring harness. Incorrect positioning of the convertible top rear module sensor connector AFFECTED VEHICLES This Service Action involves E89 (Z4) vehicles produced from March 26, 2014 to April 1, 2014. First check if a Service Action label with a code number 686 is already attached to the B-pillar. If a code number 686 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
Associated Products (7)Associated Documents - April 1, 2014•Document ID: 10148276Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 650514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTraffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
Associated Products (209)Associated Documents - April 1, 2014•Document ID: 10148273Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (242)Associated Documents - April 1, 2014•Document ID: 10148271Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 540414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelivery Stop: Wiring Harness Sensor Rear Module. A Delivery Stop has been issued on certain 2014 model year E89 vehicles produced from March 26, 2014 through April 01, 2014. These vehicles may be faulty with the routing of the micro switch connector for the retractable hard top. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be repaired prior to dealer delivery. This bulletin will be updated with instructions and warranty information when parts become available. Please contact your field representatives if you have any questions.
Associated Products (7)Associated Documents - March 1, 2014•Document ID: 10148010Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Associated Products (211)Associated Documents - March 1, 2014•Document ID: 10148008Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT
- Mfr Comm. #:
- 650314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRAD2+ Radio: Background Noise with Audio Turned Off. Background noise (buzzing, crackling, static) can be heard: * At low audio volume * When the radio is turned off * When the ignition is turned off NOTE: Background noise stops when the radio enters sleep mode. IMPORTANT: Background noise is more noticeable on vehicles produced before 09/2009 in case a RAD2+ replacement radio was installed previously. RAD2+ radio concept, manufactured from July 2009 to February 2014
Associated Products (58)Associated Documents - March 1, 2014•Document ID: 10147917Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 122413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"?SI B12 24 13 March 2014 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 24 13 dated January 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure Recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a Recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) Recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a Recall Campaign is announced by BMW NA, centers must ensure that all Recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open Recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open Recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Voluntary Emissions Recall Campaign 13E-A03: Program Control Units (OBD). Due to an error in the DME (Digital Motor Electronics) software, the required oxygen sensor onboard diagnostics (OBD) is not functioning. As a result, the ""Readiness bit"" confirmin
Associated Products (11)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents - January 1, 2014•Document ID: 10147951Service Bulletin/Repair InstructionsVISIBILITY; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Program IHKA Control Unit. The control panel for the air conditioning (IHKA) may fail intermittently. CAUSE IHKA software error
Associated Products (2)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents - January 1, 2014•Document ID: 10147928Service Bulletin/Repair InstructionsFUEL SYSTEM, OTHER:DELIVERY; ENGINE
- Mfr Comm. #:
- 160313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN52K, N54 and N20 Engine - Noise from Fuel Tank. The customer complains of a noise from the underside rear portion of the vehicle. When diagnosed the noise is coming from the fuel tank. CAUSE A manufacturing defect inside the electric fuel delivery unit (in-tank fuel pump) pressure limiting valve will result in a noise while driving. This defect will not lead to fuel pump failure or loss of power.
Associated Products (6)Associated Documents - January 1, 2014•Document ID: 10147706Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
Associated Products (54)Associated Documents - January 1, 2014•Document ID: 10053485Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE
- Mfr Comm. #:
- SIB-12-15-13
- Date Added:
- November 1, 2013
- Manufacturer:
- BMW
SummaryBMW: SERVICE ENGINE AND ENGINE MALFUNCTION LIGHT ILLUMINATES. VEHICLE MAY HAVE REDUCED POWER OUTPUT. FAULT CODE MAY NOT CLEAR FROM DME FAULT MEMORY. *KB UPDATED ON 11/8/2013. *KB UPDATED 2/21/2014 *JS UPDATED 3/11/14. *PE
Associated Products (6)Associated Documents - November 1, 2013•Document ID: 10150200Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- BMWNOV1313
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryA Delivery Stop has been issued on certain 2014 model year E89 vehicles produced from March to June 2013. The fuel pump pressure regulator could cause a noise that is audible to the driver. The fuel pump still functions properly in this case. Affected vehicles in center inventory must not be delivered until the in-tank fuel delivery unit has been replaced. Do not order parts at this time.
Associated Products (6)Associated Documents - November 1, 2013•Document ID: 10150199Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- BMWNOV1213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe Delivery Stop issued on November 22 for certain 2014 model year E89 vehicles produced from March to June 2013, remains in effect. The fuel pump pressure regulator could cause a noise that is audible to the driver. The fuel pump still functions properly in this case. Affected vehicles in center inventory must not be delivered until the in-tank fuel delivery unit has been replaced. Do not order parts at this time. The Service Information bulletin with parts and warranty information is in preparation. A follow-up DCS message will be published by Monday, December 2 with additional information.
Associated Products (6)Associated Documents - November 1, 2013•Document ID: 10150173Service Bulletin/Repair InstructionsSTRUCTURE; ELECTRICAL SYSTEM; VISIBILITY
- Mfr Comm. #:
- 513608
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
Associated Products (77)Associated Documents